Manual

ManualsBrandsPace-Edwards ManualsCarJR Series Ford Flareside

JACKRABBIT SERIES

RETRACTABLE HARD TRUCK BED COVERS

TABLE OF CONTENTS

FORD FLARESIDE

INSTALLATION INSTRUCTIONS

Tools Required for Assembly .................................... 2

Before You Start ........................................................ 2

Drain Hole Locations .................................................. 2

STEP 1: Remove Plywood Packaging ...................... 2

Packaging Contents ................................................... 2

STEP 2: Positioning Canister ................................... 3

STEP 3: Installing Rails ............................................ 3

STEP 4: Repositioning Canister................................ 3

STEP 5: Installing Tailgate End of PullStrap.............. 4

STEP 6: Installing Clamps......................................... 4

STEP 7: Lubricating & Placing Sweep Seals ........... 5

STEP 8: Installing Drain Tubes.................................. 5

STEP 9: Install Top Cover & Velcro .......................... 5

Operating Instructions ................................................ 6

Helpful Maintenance Hints ........................................ 6

Warranty Statement.................................................... 7

Part #: JR-FLARESIDE INSTALL 0611

CANISTER PART # TR2019 & TR2031

(800) 338-3697

www.paceedwards.com

Pace Edwards Company

2400 Commercial Blvd.

Centralia WA 98531

(SP1)

Summary of content (8 pages)

PAGE 1
JACKRABBIT SERIES RETRACTABLE HARD TRUCK BED COVERS FORD FLARESIDE INSTALLATION INSTRUCTIONS TABLE OF CONTENTS (800) 338-3697 www.paceedwards.com Pace Edwards Company 2400 Commercial Blvd. Centralia WA 98531 (SP1) Tools Required for Assembly .................................... 2 Before You Start ........................................................ 2 Drain Hole Locations .................................................. 2 STEP 1: Remove Plywood Packaging ......................
PAGE 2
TOOLS REQUIRED FOR ASSEMBLY: 7/16” wrench or socket 7/8” socket, ratchet #2 Phillips screwdriver Wire Cutters 5/16” wrench or socket Tape measure 3/8” wrench or socket Note: There should be no drilling into the truck body needed on most standard or full-size trucks . BEFORE YOU START: Read the instructions carefully before you start. These instructions are written for one-person installation. We have noted where briefly having an extra person’s assistance can make installation easier.
PAGE 3
IF YOU HAVE ANOTHER PERSON TO HELP STEADY THE CANISTER, IT MAY BE EASIER TO INSTALL THE RAILS (DESCRIBED IN STEP 3) BEFORE POSITIONING THE CANISTER IN THE TRUCK BED. STEP 2: POSITIONING CANISTER Remove the top cover from the canister box and set it aside for later installation. Perform a quick inventory to insure all parts are there. Be sure to check inside the small cardboard box for parts. You will need one or two support pieces (We suggest using the top of the box the Jackrabbit was shipped in.
PAGE 4
STEP 5: INSTALL TAILGATE END OF PULL STRAP HARDWARE USED: Install the tailgate end of the pull strap to the underside of the drivers side rail using the #8-32 x 3/4 machine screw located at the tailgate end on the underside of the rail. PULL STRAP x 1 (TAILGATE END) STEP 6: INSTALLING CLAMPS HARDWARE USED: PLASTIC SHIMS x 4 Before shimming and installing the rail clamps make sure the canister is centered between the truck bed rails and resting forward against the truck bed sill.
PAGE 5
STEP 7: LUBRICATING & PLACING THE SWEEP SEALS Locate the sweep seals (rubber weather strips) on the rails. Apply Pace Edwards’ UV Protectant (or 303 brand protectant) to a rag and wipe the underside of the sweep seal and the top of the wear strip. RAIL Extend the cover to the tailgate. Use an Allen wrench if needed to carefully draw out the sweep seal (seal should be angled outwards toward the cover – not rolled in toward the bed rail). (Fig.
PAGE 6
OPERATING INSTRUCTIONS 1. To open the cover, turn the actuator knob clockwise 90o until it clicks in the open position. This retracts the latches into the handle and the cover is free to roll open into the canister. A tug on the pull strap will release the latch and allow the cover to lock into the rails. 2. To latch the cover in one of the mid-range positions, pull it back just beyond the position desired and allow the cover to retract until it latches into place.
PAGE 7
C O N G R AT U L AT I O N S ! On your purchase of a Pace Edwards Retractable Truck Bed Cover. We are confident that you will get many years of trouble free service from this accessory to your truck. Please take a moment to fill out the warranty registration form to activate warranty coverage of your truck bed cover. PACE EDWARDS PRODUCT WARRANTY PACE EDWARDS (hereinafter referred to as the MFG.
PAGE 8
2400 Commercial Blvd, Centralia, WA 98531 USA (360) 736-9991 (main) (360) 736-9992 (fax) (800) 338-3697 (toll-free) www.paceedwards.