User Manual

ManualsBrandsPace-Edwards ManualsCarJR Series Honda Ridgeline

Part #: JR-SERIES Honda Rdgln Install -0611

CANISTER PART # TR2060 & FM2060

JACKRABBIT SERIES

RETRACTABLE HARD TRUCK BED COVERS

Tools Required for Assembly .................................. 2

Before You Start ...................................................... 2

Packaging Contents ................................................. 2

STEP 1: Remove Plywood & Inventory parts.......... 2

STEP 2: Attach Rail Brackets & Rails to Canister ... 3

STEP 3: Install Cab End Rail Brackets.................... 4

STEP 4: Install Cover in Truck Bed ......................... 4

STEP 5: Install Tailgate End of Pull Strap ............... 5

STEP 6: Lubricating & Placing Sweep Seals .......... 5

STEP 7: Installing Drain Tubes................................ 5

STEP 8: Install Top Cover & Velcro......................... 6

Operating Instructions .............................................. 6

Helpful Maintenance Hints ...................................... 7

Warranty Statement.................................................. 8

TABLE OF CONTENTS

(800) 338-3697

www.paceedwards.com

Pace Edwards Company

2400 Commercial Blvd.

Centralia WA 98531

HONDA RIDGELINE

INSTALLATION INSTRUCTIONS

(SP13)

Summary of content (8 pages)

PAGE 1
JACKRABBIT SERIES RETRACTABLE HARD TRUCK BED COVERS HONDA RIDGELINE INSTALLATION INSTRUCTIONS TABLE OF CONTENTS (800) 338-3697 www.paceedwards.com Pace Edwards Company 2400 Commercial Blvd. Centralia WA 98531 (SP13) Tools Required for Assembly .................................. 2 Before You Start ...................................................... 2 Packaging Contents ................................................. 2 STEP 1: Remove Plywood & Inventory parts ..........
PAGE 2
TOOLS REQUIRED FOR ASSEMBLY: 3/8” wrench or socket Razor box Knife #2 Phillips screwdriver #40 Torx wrench Wire Cutters #50 Torx wrench Drill w/ 3/4” taper drill or step drill bit BEFORE YOU START: Read the instructions carefully before you start. Due to the custom fit of this truck bed cover the installation will require a second person to help in placing the canister in the truck bed. If you have questions regarding the installation please call our Technical Support Line at (800) 338-3697.
PAGE 3
STEP 2: ATTACH RAIL BRACKET & RAILS TO THE CANISTER HARDWARE USED: Open the rail box along the length of the box; lift rails out to avoid scratching the rail surface on the package staples. REMOVE PROTECTIVE PAPER ON UNDERSIDE OF RAILS. THIS IS FOR PACKAGING PURPOSES ONLY. REAR RAIL BRACKET x 2 #8-32 x1/2” SCREWS x 4 1/4-20 x 3/4” BOLT x 2 Find the two rear rail bracket’s and four of the #8–32 X ½” countersunk screws in the hardware kit and attach them to each of the rails at the tailgate end.
PAGE 4
STEP 3: INSTALL CAB END RAIL BRACKETS & PREPARE BED HARDWARE USED: Find the two front rail brackets with rail mounting block attached to them in the hardware kit. In the truck bed remove the two factory bolts holding the front upper tie down bracket in place with a #50 torx bit. FRONT RAIL BRACKET x 2 FRONT UPPER TIE DOWN BRACKET FIG.
PAGE 5
STEP 5: INSTALL TAILGATE END OF PULL STRAP HARDWARE USED: PULL STRAP x 1 (TAILGATE END) Install the tailgate end of the pull strap to the underside of the drivers side rail in the pre drilled hole using the #8-32 x 1/2 countersunk screw. UNDERSIDE OF RAIL REAR RAIL BRACKET TAILGATE END OF PULL STRAP #8-32 x1/2” SCREWS x 1 STEP 6: LUBRICATING & PLACING THE SWEEP SEALS Locate the sweep seals (rubber weather strips) on the rails.
PAGE 6
STEP 8: ATTACHING TOP COVER & VELCRO TO PULL STRAP HARDWARE USED: Place the Top Cover on the canister and install with the two black Top Cover screws into the top cover mounting blocks. (we recommend that you use a thread locking adhesive like Loctite® on the screws) 4’ VELCRO STRIP Retract the cover to the fully open position. Attach the 4” Velcro strip onto the Velcro strip already attached to the pull strap.
PAGE 7
OPERATING INSTRUCTIONS 1. To open the cover, turn the actuator knob clockwise 90o until it clicks in the open position. This retracts the latches into the handle and the cover is free to roll open into the canister. A tug on the pull strap will release the latch and allow the cover to lock into the rails. 2. To latch the cover in one of the mid-range positions, pull it back just beyond the position desired and allow the cover to retract until it latches into place.
PAGE 8
C O N G R AT U L AT I O N S ! On your purchase of a Pace Edwards Retractable Truck Bed Cover. We are confident that you will get many years of trouble free service from this accessory to your truck. Please take a moment to fill out the warranty registration form to activate warranty coverage of your truck bed cover. PACE EDWARDS PRODUCT WARRANTY PACE EDWARDS (hereinafter referred to as the MFG.