Product Manual

ManualsBrandsPacer Pumps ManualsCentrifugal PumpsElectric Drive Centrifugal Pump — 4,800 GPH, 1 1/2in. Ports, 1/2 HP, Single Phase

OPERATION AND

SERVICE GUIDE

PO-1700

2013

‘S’ Pumps

OPERATOR’S MANUAL & PARTS LIST

for Self-priming Centrifugal Pumps

Before reading or using this manual be certain of the material of

construction of your pump. Check the model number label as follows:

POLYESTER pumps have model numbers beginning with SE

POLYPROPYLENE pumps have model numbers beginning with SP

RYTON

pumps have model numbers beginning with SY

SAFETY WARNING

Verify the chemical compatibility of the materials of your pump with the liquid you want to pump. If you are

uncertain regarding the chemical compatability contact your dealer for applications assistance and request a

copy of our corrosion resistance charts. Do not use a pump that is not chemically compatible with the liquid you

intend to pump or serious bodily injury, death, re, explosion or environmental damage could result.

ALSO, PLEASE READ SECTIONS I, II AND III BEFORE OPERATING PUMP.

I. Safety precautions ................................................................................................ 2

II. Preparing the pump for operation ........................................................................ 3

III, Pump Operating Instructions .............................................................................. 4

page no.

Electric drive Close Coupled

Gasoline Engine Drive with

Optional Roll Cage

Electric Drive long-coupled

Gasoline Engine Drive with

PROTEK System

Pedestal Mount

Hydraulic Drive

Close Coupled

Gasoline Engine Drive

Close Coupled

Summary of content (8 pages)

PAGE 1
‘S’ Pumps OPERATION AND SERVICE GUIDE PO-1700 2013 OPERATOR’S MANUAL & PARTS LIST for Self-priming Centrifugal Pumps Before reading or using this manual be certain of the material of construction of your pump.
PAGE 2
SAFETY WARNING A. Never use these pumps for pumping flammable liquids such as gasoline. AN EXPLOSION AND SERIOUS INJURY MAY RE SULT IF THIS WARNING IS IGNORED. B. In pumping corrosive materials, extreme caution should be exercised. Provide safety guards, ventilation and drains to protect people and property in case of a leak in the pump. Handling instructions from the manufacturer(s) of the liquids being pumped should be closely followed. See Page 8. C.
PAGE 3
NOTE: For liquids having specific gravities greater than 1.0, increase the rated horsepower (from catalog) by a factor equal to the specific gravity of the liquid being pumped. (Ex. Catalog HP x Specific gravity = Actual HP required) Power requirements: Consult the separate instruction sheet supplied with each hydraulic or pneumatic motor powered unit. D. Power unit preparation - Hydraulic and Pneumatic motors: NOTE: PUMP CAN LIFT WATER FROM A DEPTH OF 25 FEET.
PAGE 4
. Use a thread locking compound such as Loctite #242 on the bracket screws (Item #9 in fig. 7), and on the impeller screw (Item #16 in fig. 7). 5. The clearance between the impeller vanes and the volute face should be about .015” to .025” for good performance. This front clearance can be attained by shimming. The impeller can be shimmed from the bracket face by: a. Adding one or more washer type shims (Item #30 fig. 7) under the impeller hub. The impeller can be shimmed closer to the bracket by: a.
PAGE 5
SELF-PRIMING CENTRIFUGAL PUMP - “S” SERIES 58 45 NOTE 1: You will note a multiple choice of impellers, volutes, and top volute screws. Once you have identified the impeller (from the pump model no., or by comparing your impeller to the descriptions given the various impellers) you can make your choice of impeller, volute, or volute screws by following the same letter grouping. For example: if your impeller is black, open type, 5 vane, .535” wide, then it is part no.
PAGE 6
PP-9900-J “S” SERIES PUMP PARTS LIST ITEM # PART # GROUP PART DESCRIPTION QTY./PUMP ITEM # PART # PART DESCRIPTION QTY./PUMP 15 58-0704 30 A IMPELLER, 3 Vane, .535” wide 5.5” dia., 30 58-1837 11 SHIM, .006”, S.S. (8hp only) as required Polyester, black 1 58-1837 12 SHIM, .015”, S.S. (8hp only) as required 58-0704 40 A IMPELLER, 3 Vane, .535”wide 5.5” dia., 58-1837 13 SHIM, .030”. S.S. (8hp only) as required Polypropylene, grey 1 58-0704 60 A IMPELLER, 3 Vane, .535” wide 5.5” dia.
PAGE 7
All 3” pumps All 2” pumps All 1½” pumps All 3” pumps All 2” pumps All 1½” pumps All 3” pumps All 2” pumps All 1½” pumps All 3” pumps All 2” pumps Models starting with SE2RL, SE3SL, SE3LL and SE2JL All 1½” pumps Polyester/EPDM pumps Models starting with SEB2PL , SE2PL, SE11/2 AL and SE2FL Models starting with SEB2UL, SE2UL, SE2CL SE2IL and SE3NL Models starting with SEB2YL and SE2YL All 3” pumps All 2” pumps All 1½” pumps All 3” pumps All 2” pumps P-58-1445 P-58-1446 P-58-1447 T
PAGE 8
An Ounce of Prevention . . . Flammable solvents are often purchased in bulk and transferred manually or with motor driven pumps. Care must be taken to neutralize static electricity which may rest as a potential in the storage tank, as well as that which may rest in the receiving tank. The potential of such would, of course be greatly increased if the liquid were allowed to splash around during movement of the container.