Quick Guide Instruction Manual
HOW TO ENTER A CHARACTER
1. Press the associated button to enter a character then
2. Press
3. You have 30 seconds to enter each letter or character.
4. Letter QZ, numeric 0-9 and punctuations press
5. Press
space and for backspace
Missing Parts, contact Pach and Company 1-888-678-7224
Defective system under manufacturer warranty,
call 1-888-678-7224 for advance replacement
24 Months warranty
for complete system
6 Months warranty
for Printed Circuit Board (8PCB250)
Black Button go to programming without Master Code
What is Master Code: 4- digit code to log-on to programming mode
(0000 is default)
What is Dir (directory code): 2, 3, or 4 digit number see function
code 09. The number can be associated to apartment no., first three
digit of phone no., last four digit of phone no. , or any random no.
assigned to each tenants. Every tenant must have different directory
code number.
What is Access Code: 4-digit code for tenant to open the door or
gate.
Exit program, clear field,
reset keystroke.
19
Initialize event recording
buffer
Save program 20
Remote unlock relay 1
(1-9, 9 is default)
00
Change master code
(0000 is default)
21
Remote unlock relay 2
(1-9, 8 is default)
01 Add new tenant
40
Master code mask.
Warning: Master code
cannot be recovered if
masked. Board must be
replaced.
02 Edit existing tenant
03 Delete existing tenant 46
Display system’s
information
04 Clear all tenants 50
Clear memory to factory
default
05
Manual unlock/lock relay 1
with timer (01-98 hours, 99
hours unlock hold, 00
hours to lock)
51
Enable No Phone Bill
Must be set to 0
06 Manual unlock/lock relay 2 70
Select Modem Protocol
V22 or B212
07
Single or multi system
(single is default)
71 Enable Disable Modem
08 System ID number (n/a) 72
Invalid code lock-out
count (1-9). 3 is default
09
Directory digit (2, 3 or 4
digit, 3 digit is default)
73
Tone/pulse dialing.
Tone is default
10 Edit scrolling message 74
Enable/disable auto
answer. Enable is
default
11
Relay 1 unlock interval
(04-99 seconds, 12
seconds is default)
75
Enable/disable keypad
press beep. Enable is
default
12 Relay 2 unlock interval 76
Enable/disable speaker
beep. Enable is default
14 Set system clock 77
Enable/disable PBX.
Disable is default
15 Day light saving 78
View name and
directory
16 Display current time 79
Talk time (10-180
seconds). 60 second is
default
17 Set system date 91
Total number of tenant.
Tenant with no name
will not be included
Log on to programming: Press
simultaneously then release, welcome
message will stop scrolling (repeat if screen
still scrolls) enter 4-digit “MASTER CODE”
(0000 is default), the screen will show:
Select the “Function Code” from the table
Two ways call from the system
1. Press
to scroll name from A-Z or to scroll name from
Z-A then press
to call name selected.
2. Press
wait for dial tone then press the directory no.
Opening the door remotely
press to release relay 1
(door 1) or
to release relay 2 (door 2). Or see function
code 20 and 21
Opening the door using the access code press (display
screen will stop scrolling) then press a valid 4-digit access
code.
Extending talk time
tenant must press from the phone
after the time out warning beep.
Calling into the system
: incase you are not available when
your visitor call you. Follow steps below to use this feature
1. The system modem must be disabled and function 74 (auto
answer must be enabled).
2. Call the system’s phone no., you will hear “TWO BEEP”, then
press to talk to your visitor. Press or to release
the doo
r
PACH AND CO 1-888-678-7224 Quick Guide
TECHNICAL SUPPORT IS AVAILABLE MON-FRI
7:30AM
-
3:30PM PST AT 1
-
888
-
678
-
7224
WARNING: DO NOT USE ON BOARD
12VDC and GND TO POWER A DOOR STRIKE
OR MAGNETIC LOCK
SEPARATE POWER MUST BE USED TO
POWER A DOOR STRIKE OR MAGNETIC
LOCK.