Quick Guide User Manual
AeGISNPB9000P Page1
Technical Dept. M-F 7:30am-3:30pm PST 1-888-672-7224
Missing Parts, contact Pach and Company 1-888-678-7224
Defective system under manufacturer warranty,
call 1-888-678-7224 for advance replacement
24 Months warranty
for complete system
6 Months warranty
for Printed Circuit Board (8PCB250)
MANAGEMENT SOFTWARE FOR REMOTE
PROGRAMMING IS AVILABLE ON LINE FOR FREE
DOWNLOAD AT www.
p
ach-co.com
What is Master Code: 4- digit code to log-on to programming mode
(0000 is default)
What is Dir (directory code): 2, 3, or 4 digit number see function
code 09. The number can be associated to apartment no., first three
digit of phone no., last four digit of phone no. , or any random no.
assigned to each tenants. Every tenant must have different directory
code no..
What is Access Code: 4-digit code (keyless entry code) for tenant
to open door or gate.
Exit program, clear field,
reset keystroke
20
Add New Tenant
Directory
Save program 21 Modify Tenant Directory
00
Change master code (0000
is default)
22 Delete Tenant Directory
01 Change Talk Time 23
Clear All Tenant
Directory
02 Open Interval Relay 1 & 2 24
Card and Code (see
manual)
03 Lock-out Count 25 Card Facility Code
04 Tone or Pulse Dialing 26 Card Facility Code
05 Single or Multi System 27
Enable/Disable Modem
or RS-232
06 System ID (N/A) 28 Change Directory Digit
07 Remote enable/disable 29
Alarm Delay (see
manual)
08 Relay 2 Mode (see manual) 30
Add access code and
card
09
Alarm Telephone Number
(see manual)
31 Modify card
10
Manual Unlock/Lock with
Door Timer.
32 Delete code and card
11 Edit Welcome Screen 33
Clear All codes and
Cards
12 Set Time and Date 40 Master Code Mask
13 Time Zones (see manual) 41 Open Door Beep
14
Holiday Schedules (see
manual)
42 Enable/Disable PBX
15
Automatic Unlock Schedules
(see manual)
43
Select remote access
number door 1 and door
2
16
Clear All Time Zones
Schedules
46
Display System
Information
17
Clear All Automatic Unlock
Schedules
50 Clear memory
18 Clear All Holiday Schedules 51-60 Card Facility Code
19 Clear All Holiday Schedules 71
Enable No Phone Bill
Must set to 1
78 View Directory by Name
Log on to programming: Press
simultaneously then release, welcome
message will stop scrolling (repeat if screen
still scrolls) enter 4-digit “MASTER CODE”
(0000 is default), the screen will show:
Select the “Function Code” from the table
Two ways call from the system
1. Press to scroll name from A-Z or to scroll name from Z-A
then press to call name selected.
2. Press wait for dial tone then press the directory no.
Opening the door remotely
press to release relay 1 (door 1) or
to release relay 2 (door 2) (default setting, can be changed, see
function code 43)
Opening the door using the access code
press (wait for screen
stops scrolling) then press a valid 4-digit access code.
Extending talk time
tenant must press from the phone after the
time out warning beep.
Call waiting feature
:
1. Press 0 to transfer between two calls or to answer the second call
2. Press 0 again to return to the original call
Doorman phone
:
1. Press 0 to transfer between two calls or to answer the second call
2. Press 0 again to return to the original call
Make an outside call from Doorman phone
:
1. Press 0, wait for dial tone, then dial the phone number
1. Press after selecting a character.
2. You have 30 seconds to enter each letter or character.
3. Letter QZ, numeric 0-9 and punctuations press
4. Press space and for backspace
PACH AND CO 1-888-678-7224 Quick Guide
WARNING: DO NOT USE ON BOARD
12VDC and GND TO POWER A DOOR STRIKE
OR MAGNETIC LOCK
SEPARATE POWER MUST BE USED TO
POWER A DOOR STRIKE OR MAGNETIC
LOCK.