User's Guide

6
using your clarisonic
Prior to the first use, we recommend that you charge the
CLARISONIC brush handle overnight. For best results,
charge your
CLARISONIC for 24 hours before using it
for the first time by plugging the charger cradle into an
electrical outlet and placing the
CLARISONIC in the
charger cradle. Once your
CLARISONIC is fully charged,
it’s time to begin your
CLARISONIC experience. For your
convenience, your
CLARISONIC handle is waterproof
and may be used in the shower or bathtub. Refer to
Important Safeguards regarding the charger cradle.
The
CLARISONIC is packaged with the Sensitive brush
head (white plastic base) installed. The Normal brush
head (gray plastic base) is also included. Please select
the appropriate brush head to match your skin type and
sensitivity. Remove all makeup and wet your skin with
warm water prior to use. Liberally apply cleanser to your
skin and wet the brush head with warm water. Then
gently apply the brush to your skin, push the power
button to turn your
CLARISONIC on and gently move
the brush using a small circular motion. Pressing too
hard will slow the motion of the brush and reduce the
effectiveness.
CLARISONIC also effectively clarifies the
neck, back, décolleté (upper chest), shoulders, arms,
and the back of the hands. It is recommended that you
do not share a brush head with another individual.
Power Level
The
CLARISONIC Skin Care Brush offers a choice of
2 power levels for your cleansing needs and comfort:
normal and low power. The
CLARISONIC provides both
audible and visible indication of the power level. When
the
CLARISONIC is turned on at the normal power level,
there are 3 ascending beeps and the yellow light is
illuminated. At the low power level, 3 descending beeps
are heard and the yellow light is turned off.
Power level Audible indication Visible indication
Normal 3 ascending beeps yellow light on
Low 3 descending beeps yellow light off
To toggle between the settings, hold the power button
down for 3 seconds continuously when turning on the
CLARISONIC . The CLARISONIC will remember the
previous power setting and will indicate it audibly and
visibly as power is turned on.
7
Cleansing Timer
For even and thorough cleansing of your face, the
CLARISONIC features a proprietary one-minute T-timer™
that beeps and pauses momentarily to indicate it is time
to move to another part of your face. We recommend
that you spend the first 20 seconds of brush time on
your forehead, 20 seconds on your nose/mouth region,
and 10 seconds on each cheek. The
CLARISONIC will
shut off automatically after one minute. If you wish to
pause the cleaning cycle for up to 30 seconds, simply
press the power button. The yellow light will flash
(indicating sleep mode) and the
CLARISONIC will
remember the time remaining on the T-timer. Press the
power button to resume cleaning. When finished, rinse
your skin with warm water and rinse the brush head of
the
CLARISONIC with warm water.
To change the cleansing cycle time, turn your
CLARISONIC on and hold the power button for more
than 10 seconds. At around 3 seconds, you will hear
three tones (related to the Power Level) and then you will
hear beep tones relating to the optional cleansing times
and interval beeps. The cleansing time selections are
indicated by three different audible sequences:
Audible indication Cleansing cycle time Interval beeps
1 long beep & 2 minutes at 40, 80, and 100
2 short beeps seconds
1 long beep only 2 minutes none
1 long beep & 1 minute (this is factory at 20, 40, and 50
1 short beep selected default) seconds
Please note that you have now changed your power
setting as well as the cycle time. You may now reselect
your desired power level.
Cleanse your face
using our T-Timer
™
recommended
times and zones as
shown above.
forehead
20
seconds
Gently move the
brush using a small
circular motion.
nose/
mouth
20
seconds
each
cheek
10
seconds
page
7
page
6
0152PBLuserguide.final6 3/17/05 6:53 PM Page 6