Instructions / Assembly

ManualsBrandsPacific Entries ManualsBarn Doors72 in. x 84 in. 4-Lite Clear Coat Driftwood Mist Lite Interior Barn Door with Bronze Sliding Door Hardware Kit

Oil Rubbed Bronze Hanging Hardware

Bi-Pass Barn Door

Installation Instructions

READ ALL INSTRUCTIONS PRIOR TO STARTING!

rev. 3-10-17

page 1 of 5 - continued -

TOOLS REQUIRED

3/16” Drill Bit

Step Ladder

Pencil

Crescent Wrench

Tape

Measure

Level

Power

Drill

Phillips Head

Screwdriver

BEFORE GETTING STARTED: PRECAUTIONS

1. Please wear safety gear appropriate to tools being used. Eye protection should be used at all times. Failure to use

protective eye gear can result in serious injury. ALWAYS wear proper safety gear when operating power tools.

2. Always ensure you have ample space to operate power tools with complete control of the power tool.

3. Barn Door installation requires the install of anti-jump discs as well as end stops to ensure the door cannot come off

the track. Failure to properly install these safety items could cause serious injury or even death. These items are

required for safe operation of this Barn Door hardware.

4. The Door(s) are heavy and should be lifted by 2 people at all times. Mishandling of heavy objects (i.e., doors) may

cause a loss of balance resulting in injury. Always take precaution in assuring proper balance before moving the

door(s). Safety shoes should also be worn to prevent any foot injuries.

5. The doors roll on the track which can create pinch points (hair, fingers, clothing, etc.). Take precaution when moving

the door on the track.

6. Take care in not catching fingers in door opening when sliding the door closed.

Taking Pride in Providing You the Perfect Door

Summary of content (5 pages)

PAGE 1
Bi-Pass Barn Door Installation Instructions Taking Pride in Providing You the Perfect Door Oil Rubbed Bronze Hanging Hardware READ ALL INSTRUCTIONS PRIOR TO STARTING! TOOLS REQUIRED Pencil Level Tape Measure 3/16” Drill Bit Power Drill Crescent Wrench Phillips Head Screwdriver Step Ladder BEFORE GETTING STARTED: PRECAUTIONS 1. Please wear safety gear appropriate to tools being used. Eye protection should be used at all times. Failure to use protective eye gear can result in serious injury.
PAGE 2
PRIOR TO INSTALLING HARDWARE 1. Ensure door clearances (figure 1). 2. Install flat, no profile, head casing (not included with barn door hardware kit) securely mounted into the wall studs prior to installing the Barn Door hardware. The head casing should be a minimum of 6-1/4” tall x 3/4” thick x 160” long (figure 2). This piece should be made of hardwood that can withstand 150lbs. of weight. IT IS CRITICAL this piece be secured in the studs and level for proper travel of the barn door. 3.
PAGE 3
TRACK INSTALLATION 1. Install track by first measuring/marking hole location on the head casing (figure 3 & 4). 2. Drill 3/16” pilot holes (figure 4). MAKE SURE hole marks are level before drilling.
PAGE 4
J-HOOK/HANGER INSTALLATION 1. Install J-hook hangers (part #4) with hex bolts, washer and nuts (part #2) in factory predrilled stile holes as shown (figure 7). 2. Carefully place the doors on the track (figure 8). J-Hook Hanger (part #4) Hex Bolts, Washers & Nuts (part #2) Figure 7 Track (part #10) Figure 8 page 4 of 5 rev.
PAGE 5
J-HOOK/HANGER INSTALLATION (continued) 3. On both ends of track, install end stops (part #5) approximately 2” in from the end of the track to prevent door from rolling off (figure 9). 4. Prior to installing the anti-jump discs (part #6), operate the door back and forth carefully to check all clearances. 5. Once clearances and proper door operation are established, install anti-jump discs as shown 6” to 8” from edge of door (figure 10). 6. Install T-guide (part #3) on floor.