Installation Guide

ManualsBrandsPacific Entries ManualsBarn Doors48 in. x 80 in. Bypass Unfinished 1-Panel Solid Core Primed Pine Wood barn Door with Bronze Sliding Door Hardware Kit

Oil Rubbed Bronze Hanging Hardware

Barn Door Bypass

Installation Instructions

READ ALL INSTRUCTIONS PRIOR TO STARTING!

rev. 2-27-17

page 1 of 5 - continued -

TOOLS REQUIRED

3/16” Drill Bit

1/16” Drill Bit

Step Ladder

Pencil

Crescent Wrench

Tape

Measure

Level

Power

Drill

Phillips Head

Screwdriver

BEFORE GETTING STARTED: PRECAUTIONS

1. Please wear safety gear appropriate to tools being used. Eye

protection should be used at all times. Failure to use

protective eye gear can result in serious injury. ALWAYS

wear proper safety gear when operating power tools.

2. Always ensure you have ample space to operate power tools

with complete control of the power tool.

3. Barn Door installation requires the install of anti-jump discs

as well as end stops to ensure the door cannot come off the

track. Failure to properly install these safety items could

cause serious injury or even death. These items are required

for safe operation of Barn Doors.

4. Some Barn Door components are heavy and should lifted

with care. Mishandling may cause a loss of balance resulting

in injury. Always take precaution in assuring proper balance

before handling any heavy objects. Safety shoes should also

be worn to prevent any foot injuries.

5. The doors roll on the track which can create pinch points

(hair, fingers, clothing, etc.). Take precaution when moving

the door on the track.

6. Take care in not catching fingers in door opening when

sliding the door closed.

Taking Pride in Providing You the Perfect Door

Oil Rubbed Bronze48” Bypass Hardware

Summary of content (5 pages)

PAGE 1
Barn Door Bypass Installation Instructions Taking Pride in Providing You the Perfect Door Oil Rubbed Bronze Hanging Hardware 48” Bypass Hardware Oil Rubbed Bronze READ ALL INSTRUCTIONS PRIOR TO STARTING! BEFORE GETTING STARTED: PRECAUTIONS TOOLS REQUIRED 1. Pencil 2. Crescent Wrench 3. Phillips Head Screwdriver 3/16” Drill Bit 1/16” Drill Bit Step Ladder 4. Tape Measure 5. Power Drill 6. Level page 1 of 5 - continued - Please wear safety gear appropriate to tools being used.
PAGE 2
PARTS LIST 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Wall Bracket Standoff Hex Head Lag Bolt, 3-1/2”, Washer Hex Head Lag Bolt, 2-1/2”, Washer Hex Bolt, Washer & Open Nut Hex Bolt, Washer & Capped Nut J-Hook / Hanger 48” Track End Stop Anti-jump Disc, Screw T-Guide, Screws 3 6 3 6 3 8 4 2 4 4 2 1 5 2 7 6 3 4 9 10 11 8 PRIOR TO INSTALLING HARDWARE 1. Ensure door clearances (figure 1). 2.
PAGE 3
TRACK INSTALLATION head casing 1. First measure/mark bottom row hole location on the head casing (figure 3 & 4). 2. Then, using bottom hole location as a guide, measure/mark hole location of top two rows on the head casing (figure 3A & 4). 3. Drill 3/16” pilot holes (figure 4). MAKE SURE hole marks are level and vertically aligned before drilling.
PAGE 4
TRACK INSTALLATION (continued) 5. Use 2-1/2” Hex Bolts (part #4) to install Wall Brackets (part #1) to casing (figure 6). 6. Use Hex Bolts with Open Nuts (part #5) and Standoffs (part #2) to mount outside Track (parts #8) to Wall Brackets (figure 6). Make sure to place washers as shown.
PAGE 5
J-HOOK/HANGER & DOOR INSTALLATION (continued) 4. Prior to installing the Anti-Jump Discs (part #10), operate doors back and forth carefully to check all clearances. 5. Once clearances and proper door operation are established, install anti-jump discs as shown 6” to 8” from edge of both doors (figure 9). 6. Measure and mark floor at center point of door opening (figure 10).