Wall Mount / Flush Mount Electric Fireplace Member of HPBA With Mounting Bracket Kit for Adjustable Installation Owner’s Manual *Patented Flame Technology & Front Venting Design (No. 7236693) Model Number LND36 LND42 LND50 LND60 LND72 Item Number SELF36BTFV SELF42BTFV SELF50BTFV SELF60BTFV SELF72BTFV READ & SAVE THESE INSTRUCTIONS Carefully read and review before assembling, installing, operating, or maintaining this product. Observe all safety instructions and information.
Introduction WARNING THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED. Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before servicing. To disconnect power to the appliance, turn controls to off, then remove plug from outlet. Do not install damaged, incomplete or substitute components.
Dimensions FRONT VIEW A SIDE VIEW C G B D F TOP VIEW E Listing Approvals electric room appliances in the United States and Canada. If you need assistance during installation, please contact your local dealer. NOTE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition in the United States or the Canadian Electric Code, CSA C22.1 in Canada.
General Instructions WARNING READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION. FAILURE TO FOLLOW THEM COULD CAUSE AN APPLIANCE MALFUNCTION RESULTING IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. ALL ELECTRIC APPLIANCES HAVE HOT AND ARCING OR SPARKING PARTS INSIDE. DO NOT USE IT IN AREAS WHERE GASOLINE, PAINT OR FLAMMABLE LIQUIDS ARE PRESENT. THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE OPTIONAL ACCESSORIES LISTED IN THESE INSTRUCTIONS.
Hardware Parts List A- Fireplace LND36 LND42 LND50 LND60 LND72 x1 x1 x1 x1 x1 B- Side Brackets LND36 LND42 LND50 LND60 LND72 x4 x4 x4 x4 x4 D- Mounting Bracket LND36 x1 LND42 x1 LND50 x1 LND60 x1 LND72 x1 E- Wood Screws LND36 x9 LND42 x9 LND50 x13 LND60 x13 LND72 x16 H- Remote Control LND36 x1 LND42 x1 LND50 x1 LND60 x1 LND72 x1 I- Crystals LND36 x1 LND42 x1 LND50 x1 LND60 x1 LND72 x1 OPTIONAL OPTIONAL J- Cord Corner LND36 x2 LND42 x2 LND50 x2 LND60 x2 LND72 x2 12.15.
Locating Appliance WARNING DUE TO HIGH TEMPERATURES, THIS ELECTRIC APPLIANCE SHOULD BE LOCATED OUT OF TRAFFIC. KEEP COMBUSTIBLE MATERIALS SUCH AS FURNITURE, PILLOWS, BEDDING, PAPERS, CLOTHES AND CURTAINS AT LEAST 36” (914mm) FROM THE FRONT OF THE APPLIANCE. NEVER LOCATE THIS ELECTRIC APPLIANCE WHERE IT MAY FALL INTO A BATHTUB OR OTHER WATER CONTAINER. WEAR SAFETY GLOVES AND SAFETY GLASSES FOR PROTECTION DURING INSTALLATION AND MAINTENANCE.
Installation WARNING RISK OF FIRE! THE POWER CORD MUST NOT BE PINCHED AGAINST A SHARP EDGE. SECURE CORD TO AVOID TRIPPING OR SNAGGING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY. DO NOT RUN CORD UNDER CARPETING. DO NOT COVER CORD WITH THROW RUGS, RUNNERS OR THE LIKE. ARRANGE CORD AWAY FROM TRAFFIC AREAS AND WHERE IT WILL NOT BE TRIPPED OVER. RISK OF FIRE! TO PREVENT A POSSIBLE FIRE, DO NOT BLOCK AIR INTAKE OR EXHAUST IN ANY MANNER.
Adjustable Mounting Brackets and Installation Options avoid exposed insulation or vapour barriers coming in contact with the appliance. This will ensure clearance to combustibles is maintained. FIG. 1 FIG. 2 FIG.
Option 1: Hanging the Appliance on the Wall Due to the many different materials used on different walls, it is highly recommended that you consult your local builder before you install this appliance on the wall. 1. Select a location that is not prone to moisture and is located at least 36” (914mm) away from combustible materials such as curtain drapes, furniture, bedding, paper, etc. 2. Have two people hold the appliance against the wall to determine the BODY FRONT GLASS SIDE VIEW 3.
Positioning of Adjustable Brackets for Recessed Installation B: Side brackets C1: Top bracket (Tall) Use for more security & surface area C2: Top bracket (Short) Will stay hidden behind glass. B LND36, LND42, LND50 Builder’s bracket positions shown in grey for each model C2 B LND60 C2 B LND72 Page 10 12.15.
Option 2 & 3: Recessing the Appliance Flush into the Wall builder before you install this appliance in the wall. Select a location that is not prone to moisture and is located at least 36” (914mm) away from combustible materials such as curtain drapes, furniture, bedding, paper etc. 1. Measure the appliance and create a rough in with electrical. C1 or C2 2. Remove the front glass (refer to Page 15 for instructions). B 3. Remove the LED back lights (refer to Page 16 for instructions). 4. framing. 5.
Minimum Clearance to Combustibles Measurements are taken from the glass front Sides, back and top 0” Framing for Recessed in Wall Installation Options Finishing Material A A B B BEARING) Item No. A B LND36 19.3” (49cm) 32.60” (82.8cm) LND42 19.3” (49cm) 38.60” (98cm) LND50 19.3” (49cm) 46.60” (118.4cm) LND60 19.3” (49cm) 56.60” (143.8cm) LND72 21.27” (52.8cm) 68.60” (174.
Hard Wiring Installation WARNING TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE. HARD WIRING CONNECTION wire the appliance directly to the house hold wiring. This appliance must be electrically connected and grounded in accordance with local codes, if hard wired. In the absence of local codes, use the current CSA C22.
Wall Thermostat Installation WARNING TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE. WALL THERMOSTAT 5V INSIDE OUTSIDE BLACK BLACK BLACK BLACK THERMOSTAT WALL THERMOSTAT WIRING (24VAC) 1. Turn off circuit breaker. 2. Remove cover palte located on the left side of the appliance. 3. Pull the wire out and cut the inside thermostat. Connect the wires to the wall thermostat as shown below.
Finishing WARNING POWER SUPPLY SERVICE MUST BE COMPLETED PRIOR TO FINISHING TO AVOID RECONSTRUCTION. HEAT VENTS AND AIR OPENINGS CANNOT BE COVERED IN ANY CIRCUMSTANCES. Front Glass Removal / Installation WARNING BEFORE THE FRONT GLASS IS INSTALLED OR REMOVED, UNPLUG THE APPLIANCE AND WAIT UNTIL APPLIANCE IS COOL TO THE TOUCH. GLASS CAN BE HEAVY AND FRAGILE SO HANDLE WITH CARE. 1. Remove the 4 screws from the sides of the appliance in Figure 1. 2.
Crystal Embers Installation embers are installed. 1. Carefully place crystal embers into the bottom media tray on the front of the appliance as illustrated. Apply an even layer from side to side. your unit the most exquisite and stylish look. To order our Diamond Embers, contact our toll-free customer service number at 1-888-268-7106 LED Back Light Removal (Optional) embers are installed. 1. Unscrew the two screws in Figure A. 2. Lift off the LED cover and remove. 3.
Operating Instructions WARNING WHILE THE APPLIANCE IS OPERATING DO NOT REMOVE THE GLASS PANEL. THIS WILL CAUSE THE REMOTE CONTROL AND TOUCH PANEL TO DISFUNCTION. Once the appliance has been plugged into a grounded electrical outlet, it is ready to operate. NOTE: Ensure the house circuit breakers for the power supply are turned on. In the event of a power failure, the appliance will lose its memory function and will reset to factory mode when the power returns. Main Power Switch To turn unit power on: 1.
Multi-functional Operating with Remote Control Turning ON/OFF the appliance: 1. 2. 3. 4. Verify the lights are shut off. 5. Turn off the main power swtich. 6. Unplug the power cord. Note: The LEDs are at the brightest when the heating element is shut off. The power swtich on the appliance must be turned on for the remote control to operate. Changing the temperature: 1. 2. Press the “ ” button to turn on the heat element to HIGH temperature at 1500W. 3.
1. MCU Chips: SN8P2722 Chip 2. 3. Remote: 10 key remote 4. Item No.: LND36, LND42, LND50, LND60, LND72 NOTE: Make sure your “AA” batteries (x2) are fully charged and installed correctly in your remote control before operating. The remote control must remain within 5 meters or 17 feet of the appliance to be effective, this range may be reduced when battery power is depleted.
Wiring Diagram WARNING TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE. EMBER LED FLAME LED Page 20 12.15.
Replacement Parts WARNING FAILURE TO POSITION THE PARTS IN ACCORDANCE WITH THIS MANUAL OR FAILURE TO USE ONLY PARTS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. To order parts, contact electricfireplacescustomer@gmail.com FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE REQUIRED TO HONOUR THE CLAIM.
Replacement Parts Diagram WARNING FAILURE TO POSITION THE PARTS IN ACCORDANCE WITH THIS MANUAL OR FAILURE TO USE ONLY PARTS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. 4 10 14 11 3 13 2 8 1 7 6 5 9 12 17 15 18 19 16 20 NOTE: Care must be taken when removing and disposing of any broken glass or damaged components. Be sure to vacuum up any broken glass from inside the appliance before operation. Page 22 12.15.
Troubleshooting WARNING TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.
Limited Parts Warranty This product is inspected, tested and carefully packaged to minimize the chance of damage during shipment. If a part (excluding light bulbs and fuses*) within one year from the date of purchase proves to be defective in material or fabrication under normal use, the part will be repaired or replaced. The Company’s obligation under the warranty is to replace or repair defective parts at our discretion.