51-3849, 5/26/06 1 QC Series AH, CH, RLH , RLCH & Loader Hydraulic Windrow Sweepers Sweepster Serial Number__________________ Manual Number: 51-3849 Release Date: May 26,2006 800-456-7100 www.paladinbrands.com Sweepster 2800 N. Zeeb Rd.
51-3849, 5/26/06
51-3849, 5/26/06 3 Table of Contents Section 1 ... Installation .................................................... 5-19 Section 2 ... Operation and Maintenance ...................... 21-30 Section 3 ... Service ........................................................ 31-35 Section 4 ... Parts ............................................................ 37-68 Section 5 ... Options ....................................................... 69-78 Section 6 ... Appendix ........................................
51-3849, 5/26/06
1-3849, 5/26/06 Installation Manual QC Series Angle Brooms Table of Contents Introduction ............................................................... 6 Safety Information ............................................... 7-12 General Safety Information ..................................... 7-8 Safety Signs & Labels ........................................ 10-11 Product Information Section .................................... 12 AH/CH .................................................................
51-3849, 5/26/06 SAFETY SECTION INTRODUCTION Introduction Contacting SWEEPSTER Importance of this Manual If you have any questions about information in this manual or need to order parts, please call, write, fax or e-mail SWEEPSTER. Read this manual before attempting to operate the equipment. This operator’s manual should be regarded as part of the sweeper. Suppliers of both new and secondhand sweepers are advised to keep documentation indicating that this manual was provided with the sweeper.
51-3849, 5/26/06 Safety Information Read this manual Read all safety information in this manual. All operators must read and understand the entire contents of this manual before sweeping. General safety practices are listed on Safety Information pages and specific safety information is located throughout this manual. Hazard Definitions Four hazard classifications are used in this manual.
51-3849, 5/26/06 SAFETY SECTION GENERAL SAFETY INFORMATION Service & Repair - General CAUTION - Do not modify the sweeper in any way. Personal injury could result. If you have questions, contact your dealer or SWEEPSTER. Repair or adjust the sweeper in a safe area, away from traffic and other hazards. Before adjusting or servicing - lower the sweeper to the ground, set parking brake, shut down the prime mover and remove the key from the ignition.
51-3849, 5/26/06 9 Notes
51-3849, 5/26/06 SAFETY SECTION SAFETY SIGNS & LABELS Safety Signs and Labels There are several specific safety signs on this sweeper. The exact location of the hazards and the description of the hazards are reviewed in this section. Placement or Replacement of Safety Signs Instructions 1. Clean the area of application with nonflammable solvent, • • 2. 3. 4. and then wash the same area with soap and water. Allow the surface to fully dry.
51-3849, 5/26/06 11 SAFETY SECTION SAFETY SIGNS AND LABELS Safety Signs and Labels 2. 50-0634 4. 50-0721 6. 3. 50-0643 5. 50-0722 50-0725 7.
51-3849, 5/26/06 OPERATION SECTION PRODUCT SPECIFICATIONS Product Information Section Specifications and Model Views QC Brush Head Approximate Weight Single Motor (Brush Head Only) Width at 0° Articulation 1237 22 Length at 0° Articulation 123456 Maximum Length at 0° Articulation Maximum Width at 0° Articulation Maximum Length at Full Articulation Maximum Width at Full Articulation Sweeping Width at 0° Articulation Sweeping Width at Full Articulation Width at Full Articulation Dual Motor 38
51-3849, 5/26/06 13 INSTALLATION SECTION AH/CH Mounting, Pump & Tank Assemblies NOTE - The following give general instructions. Refer to instructions included with the mounting assembly for information specific to a particular prime mover make and model. Rear Pump Units 1. Install the mounting assembly on the tractor. 2. Attach the pump to the rear PTO shaft and secure it with the chain provided. This prevents the pump from spinning on the shaft. Front Pump Units 1.
51-3849, 5/26/06 INSTALLATION SECTION AH/CH Swing Assembly Figure 1 shows the swing assembly attached to the mounting assembly. 1. Position the swing assembly in front of the mounting assembly. Remove the pin(s) from the swing assembly. 2. Align holes in the swing assembly with ears on the mounting assembly. Slide pin(s) through the holes and secure with cotter pin(s). 3. Go to Brush Head Assembly. Brush Head Assembly 1. Position the brush head assembly in front of the swing assembly. 2.
51-3849, 5/26/06 15 INSTALLATION SECTION AH/CH Swing Cylinder Figure 4 shows the cylinder fully installed. 1. Connect a hose to each fitting on the cylinder. 2. Attach adapter fittings to hose ends. 3. Connect adapter fittings to remote valves (manual valves) or the Up port (electric valves). Lift Cylinder Figure 5 shows the lift cylinder fully installed. 1. Slide the rod end of the cylinder through the plate on the swing plate upright. Install flat washer and secure with a nut.
51-3849, 5/26/06 INSTALLATION SECTION AH/CH Adjusting Scissor Swing CAUTION - Support yokes must fit tightly to the brush frame, or damage to the swing cylinder will occur. 1. Loosen hardware holding support yokes. 2. Swing the brush head completely to the right. 3. Slide the right-hand support yoke toward the brush head until it is snug on the brush frame tube, tighten nuts. 4. Swing the brush head completely to the left. 5.
51-3849, 5/26/06 17 INSTALLATION SECTION LOADER Sweeper Installation (Broom to Prime Mover) WARNING - Improper attachment of sweeper could result in injury or death. Do not operate this machine until you have positive indication that the attachment is securely mounted. 1. Position the broom on a level surface. Removing the Sweeper WARNING - Serious injury or death may result from disengaging the sweeper when the sweeper is in an unstable position or carrying a load.
51-3849, 5/26/06 INSTALLATION SECTION RLH/RLCH Swing Assembly 1. Slide the pump onto the rear PTO. Secure with a chain. Attach the barb to the pump inlet and the elbow and relief fittings on the pump outlet (figure 7.) 2. Attach bottom plates to the swing assembly using hitch pins supplied. Plates go inside the frame with bends to the center. 3. Connect 39-link chains to bottom plates with shackles. 4. Fasten keyhole plates to the tractor toplink using pins from the tractor (figure 8). 5.
51-3849, 5/26/06 19 INSTALLATION SECTION RLH/RLCH Brush Head Assembly 1. Position the brush head assembly behind the swing assembly. 2. Align holes in the brush frame and swing assembly. Install 3 carriage bolts, flat washers, lock washers and nuts. Do not tighten the hardware; it must remain loose to level the brush head assembly. 3. Assemble the spring-chain assembly/assemblies. Attach the spring end(s) to the brush head upright. Then place the chains in the slots on the swing assembly upright. 4.
51-3849, 5/26/06 INSTALLATION SECTION RLH/RLCH Hydraulic Angle Kit NOTE - For hydraulic swing with electric valves, refer to Option - Hydraulic Swing/Electric Valve at the back of this manual. 1. Attach fittings to the cylinder with the elbow fitting on the rod end and the orifice fitting on the barrel end (figure 13). 2. Install the cylinder with the barrel end on the swing assembly and the rod end on the swing plate. Secure with cotter pins (figure 14). 3. Connect a hose to each fitting. 4.
51-3849, 5/26/06 Operation and Maintenance Manual QC Series Angle Brooms Table of Contents Operation ........................................................... 22-25 Operation ................................................................... 22-23 Storage ............................................................................ 23 Leveling Sweeper ...................................................... 24-25 Maintenance. .....................................................
51-3849, 5/26/06 OPERATION SECTION SWEEPING/OPERATING TIPS Before Each Use Engaging Functions - Tractor Mounts Perform daily maintenance as indicated in Maintenance Schedule. Methods for engaging run, swing and lift functions differ according to how the unit is equipped. Run the prime mover and sweeper at a slow idle. Check for hydraulic leaks or other problems and make corrections, if necessary, before using the sweeper. See “Hydraulic inspection guideline”.
51-3849, 5/26/06 23 OPERATION SECTION SWEEPING/OPERATING TIPS Sweeping Operating Tips To sweep: CAUTION - Avoid sweeper damage. Do not ram into piles. Use an appropriate attachment for this type of job. 1. Manual angle kit only - Swing the brush head assembly the direction that you want to direct debris. 2. Start the prime mover at idle and raise the brush. Brush, Engine & Travel Speeds 3. Rear pump units only - Engage the PTO. Vary brush, engine and travel speeds to match sweeping conditions. 4.
51-3849, 5/26/06 MAINTENANCE SECTION LEVELING THE SWEEPER Leveling B Level the sweeper for even brush wear and effective use. CAUTION - Avoid injury. Before adjusting the sweeper, always turn off the sweeper and the prime mover engine and remove the key. A 1. Move the sweeper to a flat, paved surface. 2. Lower the brush head assembly so the brush is 2 inches (51 mm) above the ground. FIGURE 15 3. Engage the parking brake and shut down the prime mover.
51-3849, 5/26/06 25 MAINTENANCE SECTION LEVELING THE SWEEPER High High Low Low Low figure 18 High High Low figure 20 Low Low High High High figure 19 Low Low High figure 21 Loader - To correct leveling problems shown in: 7. Measure to see if the brush head assembly is level when angled. First, angle the brush head to the right. Measure as in step 4. Then, angle the brush head to the left. Measure again. If measurements are equal, the sweeper is level. If not, proceed with this step.
51-3849, 5/26/06 MAINTENANCE SECTION MAINTENANCE SCHEDULE Maintenance Schedule Procedure Brush head assembly - Level Brush pattern - Check (See Pattern Adj. Section) Cylinders - Retract rods - Grease threaded and ball ends to prevent rust Drive shaft, pump - Check (AH/CH; Power Pack) Filter, air, prime mover - Clean Filter, hydraulic - Replace (AH/CH) Fittings/hoses, hydraulic - Check for leaks/tighten Check for damage Fittings, zerk - Grease.
51-3849, 5/26/06 27 MAINTENANCE SECTION MAINTENANCE RECORDS Maintenance Record Use this log to record maintenance performed on the sweeper.
51-3849, 5/26/06 MAINTENANCE SECTION BRUSH PATTERN/SPRING CHAIN/TRANSPORT CHAIN Setting Brush Pattern A properly adjusted brush offers the best sweeper performance. To check the brush pattern: 1. Move the sweeper to a dusty, flat surface. 2. Set the prime mover’s parking brake and leave the engine running. 3. Start the sweeper at a slow speed: lower it so the bristle tips touch the ground. Run the sweeper in a stationary position for 10 seconds. Swept Area 4.
51-3849, 5/26/06 29 MAINTENANCE SECTION REPLACING BRUSH SECTIONS Replacing Brush Sections 1 1. Remove motor mount screws. Retain hardware for reinstallation. Remove motor mount. 2. Remove bearing mounting plate screws from side. Retain hardware for reinstallation. 3. Lift sweeper body leaving core on ground. 4. Remove core from brush head assembly. 5. Remove old sections. 12345678952 6. Install new sections by doing the following: a. Number the tubes on the core as 1, 2 and 3 (figure 23). b.
51-3849, 5/26/06 OPERATION SECTION LUBRICATION POINTS Lubricating Zerk Fittings The following grease fittings should be greased before each use. See figure for locations. 1. Core bearing (1 fitting) 2.
51-3849, 5/26/06 31 Service Manual QC Series Angle Brooms Table of Contents Troubleshooting ................................................. 32-35 General ........................................................................... 32 Spring-Chain ................................................................... 33 Lift & Swing ..................................................................... 33 Hydraulic System ............................................................
51-3849, 5/26/06 SERVICE SECTION TROUBLESHOOTING Brush Head Problem Brush rotates wrong direction Possible Cause Possible Solution Hoses installed incorrectly Switch hoses at brush head tubes Brush slows or stops when sweeping Brush pattern too wide Travel speed too fast Adjust brush pattern to 2-3 inches (5176mm) wide: see Maintenance: Adjusting Brush Pattern Travel no more than 5 mph (8 kph) while sweeping (2-3 mph recommended) Trying to sweep too much Make several passes with sweeper materia
51-3849, 5/26/06 33 SERVICE SECTION TROUBLESHOOTING Spring-Chain Assemblies Problem Springs on spring-chain assmblies stretching Possible Cause Transport chain too loose when traveling between job sites. Travel speeds too fast when sweeping. Possible Solution Adjust according to Adjustment: Transport Chain. Do not travel at speeds over 5 mph (8 kph).
51-3849, 5/26/06 SERVICE SECTION TROUBLESHOOTING Hydraulic System Problem Hydraulic system overheats Possible Cause Possible Solution Hydraulic oil level too low Add hydraulic oil to tank until it comes to 2 inches (51 mm) from top Restriction in hoses Remove bends in hoses; remove obstructions inside hoses Host pump flow rate exceeds 18-22 gpm Contact host manufacturer for proper flow control method Hydraulic quick couplers leak Quick coupler poppet is unseated Reseat poppet; replace quic
51-3849, 5/26/06 35 SERVICE SECTION MOTOR PORTS Motor Port Identification 6789 12344523 6789 12344523 12344523 6789 6789 12344523 6789 12344523
51-3849, 5/26/06 Notes
51-3849, 5/26/06 37 Parts Manual QC Series Angle Brooms Table of Contents Parts Lists ................................................................... 38-70 Brush Head .................................................................. 38-45 Brush Head Frames ....................................................... 38 Core Assemblies ............................................................ 39 Shaft Assembly ............................................................... 40 Hydraulics-Dual Motor ....
51-3849, 5/26/06 PARTS SECTION BRUSH HEAD FRAME Brush Head Frames 12 11 13 4 16 5 1 2 Item Part Qty Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 1 18 1 27 4 6 8 2 1 1 1 1 1 1 1 1 1 1 1 Chain, 1/4 x 22 Screw, HFH, CL10.9, M6-11 x 20 Link, Quick, 5/16 Nut, Insert, M6 x 1 Ring, Snap Washer, Fender, CL8.
51-3849, 5/26/06 39 PARTS SECTION CORE ASSEMBLIES Core Assemblies 3 2 4 5 1 Item Part 1. 2. 3. 4. 5.
51-3849, 5/26/06 PARTS SECTION SHAFT ASSEMBLY Shaft Assembly 3 16 2 11 2 8 1 5 3 Item Part Qty Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 4 1 8 14 10 1 4 1 1 2 1 Screw, HHC, CL8.8, M10-1.5 x 35mm Washer, Lock, Split, Medium, M8 Washer, Flat, CL8.8, M10 Washer, Lock, Split, Medium, M10 Screw, HHC, CL10.9, M10-1.5 x 25mm Screw, HHC, CL10.9, M8-1.55 x 20mm Nut, Hex, CL10, M10-1.5 Bearing, 1 1/4, 4 Bolt Washer, .34 x 1.
51-3849, 5/26/06 41 PARTS SECTION HYDRAULIC ASSEMBLIES Hydraulic Assemblies - Dual Motor 6 9 11 8 12 3 5 7 1 2 1 4 Item Part Qty Description 1. 2. 3.
51-3849, 5/26/06 PARTS SECTION HYDRAULIC ASSEMBLIES Hydraulic Assemblies - Single Motor 11 9 18 6 4 5 13 12 7 1 2 3 Item Part Qty Description 1. 2. 3.
51-3849, 5/26/06 43 PARTS SECTION MOTOR BUCKET ASSEMBLIES Motor Bucket Assemblies 2 1 3 4 5 6 23 7 2 8 9 Item Part 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 03-4682 03-4634 03-4425 07-1044 07-3745 07-3747 07-3748 07-3749 07-4610 07-5816 07-6196 13-11890 13-12750 13-12946 Qty 1 1 1 1 4 10 4 6 2 2 1 1 1 1 Description Motor, Hydraulic, White, 17.9 Cu In, with Check Valve, Right Motor, Hydraulic, White, 17.9 Cu In, with Check Valve, Left Motor, Hydraulic, White, 24.
51-3849, 5/26/06 PARTS SECTION BRUSH HEAD STANDS Brush Head Stands 28-9737 1 4 3 2 Item Part 1. 2. 3. 4. 07-0260 07-0699 07-4748 13-13226 Qty 2 2 2 2 Description Pin, Clevis, Gr2, 3/8 x 2 3/4 Pin, Cotter, Gr2, 1/8 x 1 1/4 Pin, Lock, 3/8 x 2, Grip, Square, 2.
51-3849, 5/26/06 45 PARTS SECTION BRUSH FRAME LABELS Brush Head Labels 28-9706 Item Part Qty Description 1. 2. 3. 4. 5. 6. 7.
51-3849, 5/26/06 PARTS SECTION SWING ASSEMBLIES 11-0790 Scissor Swing Item Part Qty Description Item Part Qty Description 1. 03-1928 1 2. 03-1929 1 16. 17. 18. 07-3066 07-0223 07-0539 2 3 1 3. 4. 03-1932 03-2092 1 1 5. 03-2115 1 6. 03-2345 1 7. 8. 9. 10. 11. 12. 13. 14. 15.
51-3849, 5/26/06 47 PARTS SECTION SWING ASSEMBLIES 28-4612 Swing Plate for Tractors 4 2 1 1 9 11 12 6 5 14 18 15 17 21 8 23 7 16 2 19 3 22 13 Item Part Qty Description Item Part Qty Description 1. 03-1928 1 11. 12. 07-0206 07-0539 2 1 2. 3. 03-1932 03-2092 1 1 4. 03-2115 1 5. 03-2345 1 6. 03-4887 1 7. 8. 9. 10. 07-0079 07-0119 07-0159 07-0186 2 3 1 1 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23.
51-3849, 5/26/06 PARTS SECTION SWING ASSEMBLIES Quick Attach (SAE J2513) 9 22 4 7 1 5 6 8 6 5 2 Item Part Qty Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 3 4 1 4 1 3 1 1 1 1 1 Bolt, Carriage, Gr5, 5/8-11 x 1 3/4 Nut, Hex, Gr8, 5/8-11 Chain, 1/4, 18 Links Washer, Lock, Split, Medium, 5/8 Screw, HHC, Gr8, 5/8-11 x 2 1/2 Washer, Flat, Gr8, 5/8 Spring, Tension, 325#/IN Weld, Swing, Plate Bushing, 1 x 5/8 x .
51-3849, 5/26/06 49 PARTS SECTION SWING ASSEMBLIES 11-5031 RLCH, Cat I Hitch 11-4183 RLH, Cat I Hitch Item Part Qty Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 13. 14. 16. 17. 2 1 3 3 4 4 1 2 2 1 1 2 1 1 1 1 1 2 2 2 1 2 2 2 4 Fitting, Adapter, HP, 3/4MFS, 3/4MP Screw, HHC, Gr8, 5/8-11 x 2 1/2 Bolt, Carriage, 5/8 x 1 3/4 Washer, Flat, Gr8, 5/8 Washer, Lock, Split, Medium, 5/8 Nut, Hex, Gr8, 5/8-11 Spring, Tension, 1.87 x 10.
51-3849, 5/26/06 PARTS SECTION SWING ASSEMBLIES 11-4184 RLH, Category II Hitch Item Part Qty Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 13. 14. 16. 17. 18. 19. 20. 21. 25. 26. 27. 28. 29. 2 1 3 3 4 4 1 2 2 1 1 2 1 1 1 1 2 2 2 1 2 2 2 4 Fitting, Adapter, HP, 1 1/16MOR, 3/4MFS Screw, HHC, Gr8, 5/8-11 x 2 Bolt, Carriage, Gr5, 5/8 x 1 3/4 Washer, Flat, Gr8, 5/8 Washer, Lock, Split, Medium, 5/8 Nut, Hex, Gr8, 5/8-11 Spring, Tension, 1.87 x 10.
-3849, 5/26/06 51 Notes
51-3849, 5/26/06 PARTS SECTION SWING ASSEMBLIES 11-4200 (RLH) & 11-4202 (RLCH) Category I Hitch, with Power Pack Item Part Qty Description 1. 2. 3. 4. 5. 6.
51-3849, 5/26/06 53 PARTS SECTION SWING ASSEMBLIES 11-4200 (RLH) & 11-4202 (RLCH) Category I Hitch, with Power Pack
51-3849, 5/26/06 PARTS SECTION POWER PACK Power Pack for 3-Point Hitch for AH/CH/Loader Mounting 11-7690 (12 gpm [.76 lps]) or 11-7691 (20 gpm [1.01 lps]) Item Part Qty Description 1. 2. 03-1940 03-3142 1 1 3. 03-3779 1 4. 03-1971 1 6. 7. 03-0129 03-2473 1 1 9. 03-2443 1 10. 11. 03-0691 03-0597 03-0710 1 1 2 12. 13. 14. 03-1943 03-4709 03-0938 4 1 1 15. 03-3816 1 16. 17.
51-3849, 5/26/06 55 Notes
51-3849, 5/26/06 PARTS SECTION TANK ASSEMBLIES 11-5309 AH/CH with Manual Valve Item Part Qty Description 1. 2.
51-3849, 5/26/06 57 PARTS SECTION TANK ASSEMBLIES 11-5309 AH/CH with Manual Valve
51-3849, 5/26/06 PARTS SECTION TANK ASSEMBLIES 11-5363 AH/CH with Electric Valves Item Part Qty Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29.
51-3849, 5/26/06 59 PARTS SECTION TANK ASSEMBLIES 11-5363 AH/CH with Electric Valves 7 3 2 17 9 18 8 15 13 1 19 16 22 29 25 27 23 24 14 1 5 26 11 2 12 21 4 28 6
51-3849, 5/26/06 PARTS SECTION TANK ASSEMBLIES 11-5364 AH/CH with No Valves Item Part 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24.
51-3849, 5/26/06 61 PARTS SECTION TANK ASSEMBLIES 11-5364 AH/CH with No Valves 19 16 17 11 9 6 5 12 1 13 7 8 4 1 23 24 22 21 14 2 2 18 15 3
51-3849, 5/26/06 PARTS SECTION VALVE PACKAGES 11-4773 Manual Valves, AHH/CHH with Closed Center Hydraulic Systems Item Part 1. 2. Qty 3. 4. 03-0072 1 03-0605 1 03-0665 03-0666 03-1272 03-1022-7 1 03-1076 1 5. 03-1918 2 6. 7. 03-1943 03-1946 3 2 8.
51-3849, 5/26/06 63 PARTS SECTION VALVE PACKAGES 11-4772 Manual Valves AHH/CHH with Open Center Hydraulic Systems Item Part Qty Description 1. 03-0427 1 2. 03-0563 1 3. 03-0573 1 4. 03-0577 1 5. 03-0601 1 6. 03-0665 03-0666 03-1272 03-0602 7.
51-3849, 5/26/06 PARTS SECTION VALVE PACKAGES 13-4022 Electric Valves, Wiring Schematic
51-3849, 5/26/06 65 PARTS SECTION VALVE PACKAGES 03-2364 for 13-4022 Electric Valves - Manifold Item Part Qty Description 1.
51-3849, 5/26/06 PARTS SECTION VALVE PACKAGES 13-4022 Control Box Item Part Qty Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 07-0812 07-0815 07-0856 07-0857 07-0867 07-0917 07-0929 07-1714 07-2133 07-2264 07-2893 07-2894 07-2895 07-2896 3 2 1 1 1 13ft 1 4 16ft 5 1 1 1 1 15. 16. 17. 18. 20. 21.
51-3849, 5/26/06 67 PARTS SECTION MANUAL ANGLE 28-4626 Manual Angle Kit (CH Swing Only) Item Part 1. 2. 3. 6. 7. A. B.
51-3849, 5/26/06 PARTS SECTION HYDRAULIC ANGLE Swing Manifold Item Part Qty Description 2. 1 1 2 2 2 Manifold, 12 volt, Swing, with Screen Manifold, 24 volt, Swing, with Screen Coil, 12 volt, Delta, Manifold Block Coil, 24 volt, Delta, Manifold Block Valve Cartridge, Swing, Left/Right Kit, Seal, for 07-3080 Valve, Cartridge, Flow Divider Kit Seal, for 07-3082 4. 5. 6.
51-3849, 5/26/06 69 Options Section QC Series Angle Brooms Table of Contents Options ............................................................... 70-78 Caster Kits ............................................................. 70 Dirt Deflector ...................................................... 71-72 Hood Kits 180° ....................................................... 73 Hydraulic Angle ....................................................... 74 3PT Water Tank/Mounting ............................
51-3849, 5/26/06 OPTION SECTION CASTER KIT 13-1603 for RLH/RLCH/Loader 4 7 9 1 3 6 5 Item Part 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
51-3849, 5/26/06 71 OPTION SECTION DIRT DEFLECTOR RHFADD for RLH/RLCH Item Part Qty Description 1. 2. 3. 4. 5. 6.
51-3849, 5/26/06 OPTION SECTION DIRT DEFLECTOR Dirt Deflector Kits 28-9718 28-9719 28-9720 28-9721 5 Ft 6 Ft 7 Ft 8 Ft 4 2 4 9 2 23 8 8 7 22 5 6 Item Part 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 07-2952 07-3736 07-3736 07-3737 07-3737 07-3738 07-3738 07-3739 07-3739 07-4927 13-12833 13-12295 13-12807 13-12510 13-12834 13-12298 13-12806 13-12509 13-13303 13-13302 13-13272 13-13301 13-13415 13-13416 Qty 5 14 18 7 9 7 9 7 9 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Description Screw, HFH, CL10.
51-3849, 5/26/06 73 OPTION SECTION HOOD KITS 180° Hood Kits 28-9722 28-9723 28-9724 28-9725 5 Ft 6 Ft 7 Ft 8 Ft 5 2 4 6 3 2 Item Part 1. 2. 3. 5. 6. 07-2952 07-3617 07-4927 13-12699 13-12826 13-12397 13-13417 13-13418 Qty 19 10 3 1 1 1 1 1 Description Screw, HFH, CL10.9, M6-11 x 20 Nut, Insert, Hex, M6 x 1 Washer, Fender, CL8.
51-3849, 5/26/06 OPTION SECTION HYDRAULIC ANGLE Hydraulic Angle - Field Installed 11-4297 & 11-4298 Item Part Qty Description 1. 2. 3. 1 1 2 2 2 1 2 Cylinder, Hydraulic, 3-Bore, 7 1/2 Stroke Fitting, Elbow, HP, 90°, 9/16MOR, 3/8MFS Hose, 1/4 x 72, 1 Wire, 3/8FFS, 3/8FFS (11-4298) Hose, 1/4 x 144, 1 Wire, 3/8FFS, 3/8FFS (11-4297) Fitting, Adapter, HP, 3/8MFS, 1/4MP Fitting, Orifice, .078, Elbow, 90°, HP, 9/16MOR, 3/8MFS Pin, Cotter, 3/16 x 2 4. 5. 6.
51-3849, 5/26/06 75 OPTIONS SECTION 3PT WATER TANK 3PT Water Tank and Mounting 11-5734 Item Part 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18.
51-3849, 5/26/06 OPTIONS SECTION SPRINKLER SYSTEM Sprinkler System Item Part Qty 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 28. 29. 32. 33.
51-3849, 5/26/06 77 OPTION SECTION SPRINKLER SYSTEM Sprinkler System 12 Volt 11-4190 11-4045 11-4171 11-4062 (5 (6 (7 (8 Ft Ft Ft Ft [1.3m]) [1.5m]) [1.8m]) [2.
51-3849, 5/26/06 OPTIONS SECTION SIGHT INDICATOR KITS Sight Indicators Kit: 28-9965 Item 1. 2. 3. 4. 5. Part 07-3279 07-4036 07-6597 13-14857 13-9567 Qty Description 2 2 4 2 2 Washer, Flat, Gr8, 3/8 Nut, Hex, Nylock, 3/8-16 Screw, HFH, CL10.
51-3849, 5/26/06 79 Appendix QC Series Angle Brooms Table of Contents Bolt Torque Specifications ....................................... 80 Hydraulic Fittings Torque Specifications ............. 81-82 Glossary ............................................................ 83-84 Warranty Information ..........................................
51-3849, 5/26/06 APPENDIX TORQUE SPECS. Foot-pounds may be converted to Newton Meters by multiplying by 1.35582 Foot-pounds may be converted to Inch-pounds by multiplying by 12. If the nut and screw are not the same grade, the lower grade will always be used. NOTE - Nylock nuts are utilized when greater resistance to vibrating loose is required, and greater operating temperatures are not a factor.
51-3849, 5/26/06 81 APPENDIX TORQUE SPECS Hydraulic Torque Specifications Face Seal: Assembly, Tube to Fitting Note - Face seal fittings have the most reliable sealing method and therefore, should be used whenever possible. Installation 1. Make sure threads and sealing surfaces are free of burrs, nicks, scratches, or any foreign materials. 2. Install proper SAE o-ring to end of fitting if not already installed. Ensure o-ring is fully seated and retained properly. 3.
51-3849, 5/26/06 APPENDIX TORQUE SPECS. Hydraulic Torque Specifications Straight Thread O-ring Fitting: Assembly, Fitting to Port NOTE - Straight thread o-ring fittings are utilized to adapt hydraulic systems to motors, pumps, cylinders, and valves. Installation (Adjustable Fitting) 1. Make sure threads and sealing surfaces are free of burrs, nicks, scratches, or any foreign materials. 2. Install proper SAE o-ring on port end of fitting if not already installed.
51-3849, 5/26/06 83 APPENDIX GLOSSARY angle or angle assembly - portion of the sweeper that allows the brush head assembly to angle. manual angle kit - means of swinging the brush head assembly mechanically. BP - black pipe. mid pump unit - sweeper in which the pump is mounted on the mid PTO. brush head assembly - assembly that includes the core, hood, and brush frame.
APPENDIX GLOSSARY swing or swing assembly - portion of the sweeper that allows the brush head assembly to angle. swing cylinder - means of angling the brush head assembly hydraulically. tank assembly, hydraulic - assembly that includes the hydraulic reservoir, filter and fittings; may also incorporate valves. warning - indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. weld - weldment. windrow - pile of debris. zerk - grease fitting.
51-3849, 5/26/06 85 APPENDIX WARRANTY INFORMATION
51-3849, 5/26/06 APPENDIX WARRANTY INFORMATION SWEEPSTER ATTACHMENTS LLC Limited 12 Month Warranty Thank you for purchasing a Sweepster Attachments, LLC. product. Warranty protection is valid only when this Warranty Registration is completed and signed by the customer and dealer, and mailed to Sweepster Attachments,LLC. I hearby acknowledge that I have received a copy of the owners Limited Warranty and I accept the terms therein.
