OPERATOR’S & PARTS MANUAL ROTO-TILLER SERIAL NUMBER: ___________________ MODEL NUMBER: ___________________ 800-747-2132 I www.paladinbrands.
TABLE OF CONTENTS Introduction, General Information, Serial Number ……………………………………………….. 1 Owner and Operator Safety Information …………………………………………………………… 2-5 Definitions of Safety Terms and Symbols, Accident Prevention ……………………… 2 Safety Instructions ...............................……..…………………………………………… 3-4 Safety Signs ...............................…................................……………………………….
DEFINITION OF SAFETY TERMS AND SYMBOLS Throughout this manual, the terms DANGER, WARNING, and CAUTION are used to indicate the degree of hazard to personnel if proper safety procedures are not followed. These words will be used in conjunction with the Safety Alert Symbol: a dark triangle containing a white exclamation mark.
SAFETY INSTRUCTIONS WORK SAFELY - A CAREFUL OPERATOR IS THE BEST INSURANCE AGAINST ACCIDENTS !! SECTION 1 WARNING SECTION x x WARNING Obey all the safety instructions listed in this section and throughout this manual. Failure to obey instructions in this section could result in death or serious injury. x Use the right tool for the job at hand. Make sure that your tools are in good condition for performing the desired function.
SAFETY INSTRUCTIONS WORK SAFELY - A CAREFUL OPERATOR IS THE BEST INSURANCE AGAINST ACCIDENTS !! WHEN MOUNTING THIS PRODUCT TO YOUR POWER UNIT: x Refer to the operator’s manuals of your power unit, your loader, and your quick-attach for special or detailed mounting instructions. x This product should fit onto the quick-attach or loader arms of your power unit the same as the original products that were designed by your loader / quick-attach manufacturer.
SAFETY SIGN LOCATIONS ITEM 1 2 3 4 QTY. 1 1 2 1 PART # 50-0723 50-0724 RDL3100 RDL3178 DESCRIPTION READ MANUAL HYDRAULIC STAND CLEAR NOT A STEP INSTRUCTIONS x x x x PLACEMENT OR REPLACEMENT OF SAFETY SIGNS Keep all safety signs clean and legible. Replace all missing, illegible, or damaged safety signs. Replacement parts for parts with safety signs attached must also have safety signs attached. Safety signs are available, free of charge, from your dealer or from FFC Attachments. ITEM 1 1.
POWER UNIT SPECIFICATIONS IMPORTANT Exceeding any of the maximum recommended power unit specifications CAN result in damage to this product and WILL void all FFC Attachments warranties. DESCRIPTION Weight of Power Unit without Planer Operating Capacity of Power Unit’s loader Lift Capacity of Power Unit’s loader Hydraulic Pressure Output Rear Ballast SPECIFICATIONS 11,000 lbs. maximum 3,750 lbs. maximum 7,500 lbs. maximum 3,500 psi. maximum As required to maintain full power unit stability.
ROTO-TILLER OPERATION SAFETY FIRST!! READ AND UNDERSTAND THE SAFETY INSTRUCTIONS (pages 2-5 of this manual) BEFORE BEGINNING ANY ROTO-TILLER OPERATION WARNING Failure to obey the following procedures could result in death or serious injury. x Never lift the lowest portion of this product higher than 1’-0” above the ground while operating. x Do not lock the auxiliary hydraulics of your power unit in the “ON” position. x Keep everyone at least nine feet away from the unit when operating.
ROTO-TILLER SERVICE SAFETY FIRST!! READ AND UNDERSTAND THE SAFETY INSTRUCTIONS (pages 2-5 of this manual) BEFORE BEGINNING ANY ROTO-TILLER SERVICE Removing Wire, Twine, Weeds, etc. that are Wrapped Around the Roller 1. Park your power unit on a level surface with this product properly attached. 2. Place your power unit’s transmission in “Park” and engage the parking brake. 3.
PARTS ILLUSTRATION 9
ROTO-TILLER: PARTS LIST ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 QTY.
Model Number LAF3438 LAF3452 LAF3468 Overall Width 53” 67-13/16” 78-1/4” ROTO TILLER SPECIFICATIONS Overall Overall Offset to Height Depth Right 27” 27” varies 27” 33-1/2” 12-1/2” 27” 33-1/2” 4-3/4” Torque @ 2,500 psi 469 ft. lbs. 939 ft. lbs. 939 ft. lbs. Shipping Weight 450 lbs. 600 lbs. 695 lbs. All replacement hydraulic hoses must have a minimum rated working pressure of 4,000 psi. TORQUE SPECIFICATIONS FOR STANDARD MACHINE HARDWARE (FOR REFERENCE ONLY) Bolt Size 0.31 - 18 0.50 - 13 0.
PLEASE TRI-FOLD AND AFFIX TAPE HERE Warranty Registration Form and Delivery Inspection Report IMPORTANT! Warranty Void if card is not returned with 10 days. All Applicable sections must be filled in. This section to be filled out and signed by Dealer at time of delivery.
FFC LIMITED 12 MONTH WARRANTY Thank you for purchasing a FFC product. Warranty protection is valid only when this Warranty Registration is completed and signed by the customer and dealer, and mailed to FFC. I hereby acknowledge that I have received a copy of the owners Limited Warranty and I accept the terms therein.
