Instructions

INSTALLATION
WARNUNG: Vor Montage- und Installationsarbeiten Spannung
freischalten!
Nachfolgende Schritte zur Installation ausführen:
1 - Spannung freischalten und prüfen.
2 - Installieren des Dimmaktors gemaß der dargestellten Anschlussbilder:
· Abb. 1: Vier (4) separate Kanale.
· Abb. 2: Ein (1) RGBW Kanal.
· Abb. 3: Ein (1) RGB Kanal + ein (1) separater Kanal.
3 - Korrekte Installation und Verkabelung überprüfen.
4 - Spannungsversorgung einschalten.
5 - KNX-Busspannung einschalten.
INBETRIEBNAHME
1 - Programmiertaste (B) drücken. Die LED leuchtet grün.
2 - Physikalische Adresse und Konfiguration mittels ETS in das Gerat
übertragen. Der Download der Produktdatenbank kann über den Link
www.hugo-mueller.de/downloads/knx-produktdatenbank/ erfolgen.
3 - Nach erfolgtem Download geht die grüne LED aus. Die Applikation /
Konfiguration wurde erfolgreich übertragen und das Gerat ist
betriebsbereit.
PROGRAMMIERTASTE UND STATUS LED (B)
Die integrierte Status-LED (in der Programmiertaste) zeigt zusätzlich
mögliche Blockierungen des Dimmers an. In diesem Fall blinkt die LED
abwechselnd rot und grün. Dieser Fehler wird in der Regel durch eine
fehlerhafte Konfiguration in der ETS hervorgerufen.
Der Fehler kann wie folgt behoben werden:
- KNX-Bus Stecker (C) abklemmen.
- Nach ein paar Sekunden die Programmiertaste drücken und gedrückt
halten.
- Bei gedrückter Programmiertaste den KNX-Bus Stecker (C) wieder
anschließen.
- Anschließend Konfiguration in der ETS korrigieren und erneut in das
Gerat übertragen.
WARNUNGEN UND EINSCHRÄNKUNGEN
• Die Spannungsversorgung muss gemaß den Vorschriften abgesichert
sein.
• Das Gerät muss während der Installation spannungsfrei geschaltet sein
und darf nur von qualifiziertem Fachpersonal installiert werden.
• Keine Spannungsversorgung am Dimmer anlegen, wenn keine
Lampenlast ängeschlossen ist.
• Vor Arbeiten an den Lasten (z.B. auswechseln, entfernen oder hinzufügen
von Leuchten) immer Spannungsversorgung freischalten.
• Die maximale Last (gemäß Angaben) nicht überschreiten.
• Dimmer nicht direkt neben anderen Geräten platzieren. Es sollte
mindestens eine Modulbreite (1 TE) Abstand zu benachbarten Geräten
eingehalten werden.
• Im Zuge der Schaltschrankplanung sollten mögliche Wärmeentwicklungen
der Dimmer berücksichtigt werden. Je nach Anwendung können auch
Zwangsbelüftungen notwendig sein.
• Das Gerät kann bei Überlast, Kurzschluss oder auch Überhitzung
blockieren. In diesem Fall Spannungsversorgung vom Gerät trennen, den
Fehler lokalisieren, beheben und anschließend die Spannungsversorgung
wieder anschließen.
R G B W
AUTO
MANUAL
V-V+/LED+V+/LED+ V-
Panic
L
N
230V~ 50Hz
-
+
Bus KNX
NETZTEIL
POWER SUPPLY
V+
V-
12-48VDC
-
+
-
+
-
+
-
+
Abb. 1 / Fig. 1
R G B W
AUTO
MANUAL
V-V+/LED+V+/LED+ V-
R
Panic
L
N
230V~ 50Hz
-
+
Bus KNX
V+
V-
-
+
R
-
G
-
B
-
W
R G B W
AUTO
MANUAL
V-V+/LED+V+/LED+ V-
R
Panic
L
N
230V~ 50Hz
-
+
Bus KNX
V+
V-
-
+
R
-
G
-
B
W
-
+
INSTALLATION
WARNING: Disconnect the main supply before the installation!
Follow these steps for installation:
1 - Disconnect the main supply voltage.
2 - Install the device according to the schematics / wiring diagrams:
· Fig. 1: Four (4) independent channels.
· Fig. 2: One (1) RGBW channel.
· Fig. 3: One (1) RGB channel + one (1) independent channel (W).
3 - Verify proper installation and wiring.
4 - Switch-on mains supply voltage.
5 - Switch-on KNX bus supply voltage.
COMMISSIONING
1 - Press the programming key (B). The programming LED lights up
green.
2 - Transmit the physical address and configuration into the dimmer via
ETS4 or higher. To download the product application go to
www.hugo-mueller.de/downloads/knx-product-database/
3 - After transmission, the green LED turns off. The application has been
loaded successfully and the dimmer is ready for use.
PROGRAMMING KEY AND STATUS LED (B)
The integrated status LED (inside the programming key) also displays a
possible blocking of the dimmer. If a blocking occurs, the LED flashes
alternating red and green. This error is usually caused by incorrect
programming via ETS.
In order to reset the error:
- Remove KNX-Bus terminal connector (C).
- After a few seconds, press and hold the programming key (B).
- While keeping the programming key pressed, reconnect the KNX-Bus
terminal connector (C).
- Correct the configuration in ETS and re-transmitt to the device
CAUTIONS AND LIMITATIONS
• The mains supply must be protected (fused) according to existing rules.
• The device must be installed while mains power supply is disconnected
and only by qualified personnel.
• Do not apply power (mains) if the dimmer is without load.
• Disconnect the mains before handling the load, e.g. replacing burned-out
lightbulbs, or when removing or adding new ones.
• Do not exceed the maximum (rated) load of the device.
• Do not install dimmers close / next to each other. Leave at least one
module width space between them or any other sources of heat.
• Design the installation / switching cabinet properly to avoid heat problems.
In some cases additional, forced ventilation might be necessary.
• The device may block if the overload, short-circuit or thermal protection
are activated. Disconnect the supply voltage (mains), correct the fault and
reconnect the supply voltage (mains) afterwards.
NETZTEIL
POWER SUPPLY
12-48VDC
NETZTEIL
POWER SUPPLY
12-48VDC
WARNUNG! Gefährliche Spannung! Es besteht Lebensgefahr
durch elektrischen Schlag oder Brandgefahr!!!
Einbau, Anschluss und Montage dürfen ausschließlich von einer
entsprechend geschulten Elektrofachkraft durchgeführt werden!
Nur an die auf dem Gerät angegebene Spannung / Frequenz
anschließen! Vor Montage / Demontage und Installationsarbeiten muss
das Gerät spannungsfrei geschaltet werden und die Spannungsfreiheit
geprüft werden!
Beschädigte Geräte dürfen nicht in Betrieb bzw. müssen umgehend
außer Betrieb genommen werden!
WARNING: Hazardous voltage! Risk of death, fire and electric
shock!!!
Installation and assembly of electrical equipment must be carried out only
by professional and trained electricians!
Connect only proper supply voltage and frequency as stated on the
product!
Disconnect device from power supply prior to wiring and installation!
Check power supply is disconnected!
Defective devices have to be put out of service immediately!
en
de
Abb. 2 / Fig. 2
Abb. 3 / Fig. 3