Use and Care Manual

3
NORSE Operating Manual & Parts List 9686006
GETTING STARTED
SAFETY / SPECIFICATIONS
ASSEMBLY / INSTALLATION
OPERATION
TROUBLESHOOTING
MAINTENANCE / REPAIR
GETTING STARTED
Description:
The NORSE Dust Collector is designed to remove and collect
wood dust and wood chips from woodworking machinery. Lower
polypro pylene bag collects dust and chips while upper cloth bag
filters fine dust. Lower bag design makes disposal of dust and chips
easy. Collector features 4” intake hose and casters on base for
mobility.
Do not use this dust collector in a
flammable or explosive atmosphere. Do
not use to collect aluminum or magnesium dust, nor any
other chemically reactive dusts. Consult National Fire
Protection Association (NFPA) standards before setting up a
dust collection system, especially NFPA 664.
Structural Requirements:
Make sure all supporting structures and load attaching
devices are strong enough to hold your intended loads. If
in doubt, consult a qualified structural engineer.
Electrical Requirements:
The power supply to the Dust Collector needs to be
120/240 volt, 12/6 amp, 60 Hz. The standard allowable
voltage variation is plus or minus 10%.
Tools Needed:
Standard mechanic’s hand tool set.
UNPACKING
Be careful not to touch overhead power
lines, piping, lighting, etc. if lifting equip -
ment is used. Dust Collector weighs approximately 101 lbs,
proper tools, equipment and qualified personnel should be
employed in all phases of unpacking and installation.
Carton should be handled with care to avoid damage from
dropping, bumping, etc. Store and unpack carton with correct side
up. After unpacking Dust Collector, inspect carefully for any
damage that may have occurred during transit. Check for loose,
missing or damaged parts. If any damage or loss has occurred,
claim must be filed with carrier immediately. Check for
completeness. Immediately report missing parts to dealer.
Contents:
• Main Base Plate Assembly (1)
• Collector Assembly (1)
• Main On-Board hose (1)
• Motor/Fan Assembly (1)
• Collector Support (3)
• Upper Bag Support (1)
• Double Inlet Adaptor (1)
• Caster (4)
• Motor Support Bracket (1)
• Main Fan Assembly Outlet (1)
• Main Fan Assembly Outlet Seal (1)
• Large Pipe Clips (2)
• Small Pipe Clips (2)
• Filter/Collection Bag Retaining Straps (2)
• Caster Fixing Kit (4 Sets)
• Main Assembly Fixing Kit (1 Set)
• Operating Instructions & Parts Manual (1)
Unpack:
Do not discard packing materials until after Dust Collector
has been inspected for damage and completeness.
Locate loose parts and set aside.
Inspect:
After unpacking the unit, carefully inspect for any damage
that may have occurred during transit. Check for loose,
missing or damaged parts. Shipping damage claims
must be filed with the carrier.
All tools should be visually inspected before use, in addition to
regular periodic maintenance inspections.
Be sure that the voltage labeled on the unit matches your power
supply.
See General Safety Instructions, Cautions and
Warnings as shown.
SAFETY RULES
For your own safety, read all of the
instructions and precautions before
operating tool.
PROPOSITION 65 WARNING: Some dust created by
using power tools contain chemicals known to the state
of California to cause cancer, birth defects or other
reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonry
products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
work in a well ventilated area and work with approved safety
equipment. Always wear OSHA/NIOSH approved, properly fitting
face mask or respirator when using such tools.
Always follow proper operating
procedures as defined in this manual even
if you are familiar with the use of this or similar tools.
Remember that being careless for even a fraction of a
second can result in severe personal injury.
9686006_oipm_En012_9643286.01 0318 03/07/18 Page 3