OWNER'S MANUAL 34CM CORDLESS REMOTE COLOUR TELEVISION MODEL: 3410 Type Tested Electrical Safety AS/NZS 3250 Lic 4163 Standards Australia APP No: N15957 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.
Congratulations on your purchase of this Palsonic colour television receiver. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this receiver. Retain is manual in an easily accessible location for future reference. Contents Main features ............................................................................................................. Notes for operation .........................................................................
Main features . . . . . . . . . . . Hyperband. Auto/manual search. Voltage synthesised system 100 preset channels. TV system: PAL-B/G, NTSC-4.43/3.58 (AV). Full function remote control & English on screen menu display No-signal blue background display and AUTO-POWER-OFF function. Four picture mode settings. Sound mute function. Sleep timer. AV IN/OUT S-VHS operation function.
NOTES FOR OPERATION * Do not let the TV set be in standby condition for a long period of time. When it is not in use, please turn off the power supply and remove the power plug. When it is to be left for a prolonged period of time, it is recommended to disconnect the connection to the outdoor aerial, to avoid thunder strike. * Please follow cautions for safety in the TV set instructions, and all warnings and descriptions denoted on the TV set.
Installation and appearance Antenna connection To ensure a bright-coloured and clear picture, you should use an outdoor aerial or CATV cable. If the signals are strong enough, you may use an indoor aerial. Note: In case of using the Twin-lead aerial feeder (300 ) for UHF/VHF aerial, use a 300-75 ohm adaptor (not supplied) When using the coaxial cable (not supplied) (75 ) for UHF/VHF aerial, connect the plug into the 75 ohm aerial socket directly.
Appearance Front view POWER SWITCH REMOTE SENSOR INDICATOR MENU TV/AV VOL (down) VOL (up) Note: Functions of MENU, remote controller.
The remote controller Standby Sound mute TV/AV select Previous channel On screen recall Channel direct select Colour system select Picture control Sleep timer Picture mode selection Volume control *Sound system select Channel select * NOTE: this TV model's RF sound system is BG only. Therefore the SYS1/2 button on the remote controller is ineffective in sound system selection. Similarly in the Preset and Function menus the SYS item (sound system selection item) is ineffective.
Operation Turning the power on/off 1. Connect the power, push the main power switch, the red indicator is on, the set is in standby mode. 2. Push the button on the remote controller to turn on the set when the set is in standby, this time, the green indicator is on, on the upper right corner of the screen will display channel number, colour and sound system. Or you can push the CH button to turn on the set when in standby. 3.
Press the VOL button to enter into the sub-menu. To exit the menu press the MENU button. Note: the menu displayed on the screen will disappear automatically in 10 seconds if not in operation. 1. PICTURE menu Making use of the PICTURE menu can adjust the picture effect according to your personal preference and it will be stored as picture memory mode automatically. Press the CH button to select the item (the selected item is highlighted in red). Press the VOL button to adjust it. The range is 0-63.
2. PRESET menu PROG SKIP AFT BAND 28 OFF ON U SYS 1 AUTO SEARCH MANUAL Making use of the PRESET menu can fulfil the function of auto-search, search. manual search , channel and band selection. AFT and skip on/off. Press CH button to select the item. (the selected item is highlighted in red). Press the MENU button to exit to the main menu. 1) PROG (program) Select the current program number while "PROG" is highlighted. Press VOL increase or decrease the program number progressively.
5) SYS (sound system) This item is used to select sound system. Since this TV model’s RF sound system is B/G only, this item gets into ineffectiveness in sound system selection. 6) Auto - search (AUTO) Press CH button to highlight AUTO. Press VOL button the set will automatically search and store the active TV signals in your local area from lower band to higher band in the sequence of VL VH U with the green bar moving rightward.
3. FUNCTION menu STD AUTO SYS 1 BLUE ON Making use of the FUNCTION menu can select BLUE ON/OFF and current channel’s colour and sound system. Press CH button to select item (the selected item is highlighted). Press MENU button to exit to the main menu. 1) STD (colour system) selection. In this TV model the colour system is automatically identified. In normal circumstances, please set colour system to AUTO. 2) SYS (sound system) selection. In this TV model this item is ineffective.
-Press " 2 " Press "-/--" 25 AUTO SYS 1 2Press " 5 " Two digit mode 2. Using CH Press CH button button, the channel number will be increased or decreased progressively. 3. Making use of Press button button to swap the currently viewed channel with the previous channel. 1 AUTO SYS 1 20 AUTO SYS 1 Press Picture and volume adjustment 1.
2. Volume adjustment You can press the VOL button to adjust the volume, and the green bar will move rightward or leftward, the volume output range is 0-63. Press VOL VOLUME 15 VOLUME llllll...... 30 llllll...... Press VOL You can press the button to mute the sound. Press the The sound is restored to normal. SOUND MUTE MODE button again or VOL button. NORMAL SOUND MODE Press Press Press VOL VOLUME 15 llllll......
Other functions 1. Retain on-screen display Press the + button and the upper right corner will display the current channel number and TV system. After 4 seconds the display on the screen will disappear. Press + 2 AUTO SYS 1 After 4 seconds In VIDEO mode, it will only display VIDEO l (or VIDEO 2) and the colour system. 2.
When the SLEEP timer is functioning, if you press SLEEP button again, the TV will display the remaining time. If the power is switched off, the SLEEP timer will be cancelled. You must set it again if wanted. 4. TV/AV selection Press the TV/AV button on the set or AV button on the remote controller to select TV or AV mode.
External equipment connection This set is incorporated with Audio & Video input and output sockets which allow direct connection to external equipment (such as VCR, Video DISC, VCD, Satellite Receiver etc.) for playing back and recording the programs. 1. VIDEO PLAYBACK The figure below shows how to connect the TV set to the video equipment. NOTE: The VIDEO equipment may be VCR, Video DISC, VCD or Satellite Receiver.
3. DUBBING The picture below shows how to connect TWO VCRs to the TV for dubbing one from the other. Press AV button on the remote control unit to select AV mode before dubbing, "AV" will be displayed on the screen. The TV set will act as a monitor to help you edit while dubbing. NOTE: The set MUST remain in Video mode and MUST NOT be switched off during the session.
TROUBLE SHOOTING If any problem arises in the operation of your set, first check through this list of symptoms and correction. Should the problem be unsettled, unplug the set and contact your dealer. Symptoms . . . . . No picture, no sound. Poor sound, picture OK. Poor picture, sound OK. Snowy picture Lines in picture Distorted picture Weak picture. Multiple images (Ghost) Poor colour or no colour Check these things . Be sure power cord is plugged in. . May be station trouble. .
SPECIFICATIONS Power Supply Receiver Channel Cable Channel TV System Dimension (mm) Weight CRT Power Consumption Antenna Impedance : AC 240V, 50Hz : VHFL 0~5, 5A; VHFH 6~11; UHF E21-E69 : S1-S41 (Hyperband) : PAL-B/G, NTSC 3.58 /4.43 : 430 (W) x 339 (H) x 370 (D) : 12 kg : 34cm : 60W : 75 ohm Remote Control Unit Power Supply Accessories : DC 3V (2 x UM-3) : one remote controller Note : Design and specifications are subject to change without notice.
PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.