OWNER'S MANUAL 34CM CORDLESS REMOTE COLOUR TELEVISION MODEL: 3499M Type Tested Electrical Safety AS/NZS 3250 Lic 4163 Standards Australia APP No: N15957 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.
Congratulations on your purchase of this Palsonic colour television receiver. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this receiver. Retain is manual in an easily accessible location for future reference. Contents Main features ............................................................................................................. Notes for operation .........................................................................
Main features . . . . . . . . . . . Hyperband. Auto/manual search. Voltage synthesised system 100 preset channels. TV system: PAL-B/G, NTSC-4.43/3.58 (AV). Full function remote control & English on screen menu display No-signal blue background display and AUTO-POWER-OFF function. Four picture mode settings. Sound mute function. Sleep timer. AV IN/OUT terminals.
NOTES FOR OPERATION * Do not let the TV set be in standby condition for a long period of time. When it is not in use, please turn off the power supply and remove the power plug. When it is to be left for a prolonged period of time, it is recommended to disconnect the connection to the outdoor aerial, to avoid thunder strike. * Please follow cautions for safety in the TV set instructions, and all warnings and descriptions denoted on the TV set.
Installation and appearance Antenna connection To ensure a bright - coloured and clear picture, you should use an outdoor aerial or CATV cable. If the signals are strong enough, you may use an indoor aerial. Note: In case of using the Twin-lead aerial feeder (300 ) for UHF/VHF aerial, use a 300-75 ohm adaptor (not supplied) When using the coaxial cable (not supplied) (75 ) for UHF/VHF aerial, connect the plug into the 75 ohm aerial socket directly.
Appearance Front view INDICATOR REMOTE SENSOR POWER SWITCH STANDBY CH CH VOL MENU TV/AV VOL Back view ANTENNA INPUT VIDEO IN/OUT AUDIO IN/OUT 5
The remote controller Standby Sound mute TV/AV select Previous channel On screen recall Channel direct select Colour system select Picture control Sleep timer Picture mode selection Volume control *Sound system select Channel select * NOTE: this TV model's RF sound system is BG only. Therefore the SYS1/2 button on the remote controller is ineffective in sound system selection. Similarly in the Preset and Function menus the SYS item (sound system selection item) is ineffective.
Operation Turning the power on/off 1. Connect the power, push the main power switch, the red indicator is on, the set is in standby mode. 2. Push the button on the remote controller to turn on the set when the set is in standby, this time, the green indicator is on, on the upper right corner of the screen will display channel number, colour and sound system. Or you can push the CH button to turn on the set when in standby. 3.
Press the VOL button to enter into the sub-menu. To exit the menu press the MENU button. Note: the menu displayed on the screen will disappear automatically in 10 seconds if not in operation. 1. PICTURE menu Making use of the PICTURE menu can adjust the picture effect according to your personal preference and it will be stored as picture memory mode automatically. Press the CH button to select the item (the selected item is highlighted in red). Press the VOL button to adjust it. The range is 0-63.
Making use of the PRESET menu can fulfil the function of auto-search, search. manual search , channel and band selection. AFT and skip on/off. Press CH button to select the item. (the selected item is highlighted in red). Press the MENU button to exit to the main menu. 1) PROG (program) Select the current program number while "PROG" is highlighted. Press VOL increase or decrease the program number progressively. 0 PROG 1 2 button to 99 2) SKIP-ON/OFF Press CH button to highlight SKIP ON/OFF.
sequence of VL VH U with the green bar moving rightward. When a station is located, the set will store the signals with a channel number from 0. When all the signals are searched and stored, the TV returns to 0 channel automatically, auto-search is finished. * After auto-search, all programs colour system is set to AUTO and in AFT-ON mode. * During the process of auto-search, if MENU or CH button is pressed, the searching is interrupted. Press VOL button the searching begins again.
2) SYS (sound system) selection. In this TV model this item is ineffective. (Refer to the NOTE on page 6) 3) BLUE ON/OFF selection. Select and highlight BLUE ON/OFF. Press VOL button to select ON or OFF. When "BLUE ON" is selected, blue background will appear on the screen automatically when no input signals, and the sound is mute. After 5 minutes the set will cut off automatically. Channel selection 1. Using direct select buttons 1) Single digital method ( 0~9 ).
Picture and volume adjustment 1. Picture adjustment Press PIC button repeatedly, on-screen display will change in the sequence below PAL NTSC Press VOL BRIGHTNESS CONTRAST BRIGHTNESS CONTRAST COLOUR COLOUR SHARPNESS TINT SHARPNESS button to adjust the level. For example, to adjust brightness: Press " Press "PIC" BRIGHTNESS " 30 llll....... Press " After 4 seconds BRIGHTNESS 63 lllllllllll " BRIGHTNESS 0 l..........
Picture mode selection You can select the picture quality instantly among three presets modes and one user-set mode. Press the button to select the desired picture quality. DYNAMIC, STANDARD, MILD and MEMORY (user-set) can be selected cyclically. MEMORY DYNAMIC MILD STANDARD Item Output Brightness Colour Contrast Tint Sharpness DYNAMIC 31 31 47 31 31 STANDARD 31 31 31 31 31 MILD 31 31 21 31 31 Mode MEMORY The picture quality you set Other functions 1.
COLOUR SYSTEM Colour Sub-Carrier Vertical Frequency PAL (RF/VIDEO) 4.43MHz 50Hz NTSC 3.58 (VIDEO) 3.58MHz 60Hz PAL (RF/VIDEO) 4.43MHz 50Hz PAL 60 (VIDEO) 4.43MHz 60Hz N358 NTSC 3.58 (VIDEO) 3.58MHz 60Hz N443 NTSC 4.43 (VIDEO) 4.43MHz 60Hz AUTO PAL 3. SLEEP timer Using the SLEEP button allows you to have the appliance automatically turned off after a preset time (the time range will be as long as 120 minutes) , and set the appliance to standby mode.
AV PAL 12 PAL Press AV After 4 seconds Press AV Note: 1) When receiving broadcasting TV program (the TV signals are input through aerial terminal), press the AV button to switch the set to TV mode. 2) When receiving programs played back by Video DISC., VCR, Satellite receiver, VCD (the signals are input through AV terminals), please set the receiver to AV mode.
External equipment connection This set is incorporated with Audio & Video input and output sockets which allow direct connection to external equipment (such as VCR, Video DISC, VCD, Satellite Receiver etc.) for playing back and recording the programs. 1. VIDEO PLAYBACK The figure below shows how to connect the TV set to the video equipment. NOTE: The VIDEO equipment may be VCR, Video DISC, VCD or Satellite Receiver.
3. DUBBING The picture below shows how to connect TWO VCRs to the TV for dubbing one from the other. Press AV button on the remote control unit to select AV mode before dubbing, "AV" will be displayed on the screen. The TV set will act as a monitor to help you edit while dubbing. NOTE: The set MUST remain in Video mode and MUST NOT be switched off during the session.
TROUBLE SHOOTING If any problem arises in the operation of your set, first check through this list of symptoms and correction. Should the problem be unsettled, unplug the set and contact your dealer. Symptoms . . . . . No picture, no sound. Poor sound, picture OK. Poor picture, sound OK. Snowy picture Lines in picture Distorted picture Weak picture. Multiple images (Ghost) Poor colour or no colour Check these things . Be sure power cord is plugged in. . May be station trouble. .
SPECIFICATIONS Power Supply Receiver Channel Cable Channel TV System Dimension (mm) Weight CRT Power Consumption Antenna Impedance : AC 240V, 50Hz : VHFL 0~5, 5A; VHFH 6~11; UHF E21-E69 : S1-S41 (Hyperband) : PAL-B/G, NTSC 3.58 /4.43 : 366 (W) x 333 (H) x 373 (D) : 12 kg : 34cm : 60W : 75 ohm Remote Control Unit Power Supply Accessories : DC 3V (2 x UM-3) : one remote controller Note : Design and specifications are subject to change without notice.
PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.