OWNER'S MANUAL PURE FLAT HI-VISION STEREO TELEVISION 80CM CORDLESS REMOTE COLOUR TELEVISION MODEL: 8040PFST Type Tested Electrical Safety AS/NZS 3250 Lic 4166 Standards Australia APP No: N15900 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www.palsonic.com.
Main features . . . . . . . . . . PAL/NTSC/SECAM Multi-System Hyperband Hyperband English/Chinese on-screen menu display Surround sound and wide - field dynamic sound system NICAM Digital Stereo/bilingual broadcasts receivable German Stereo (IGR)/bilingual broadcasts receivable Three groups of S-VIDEO/VIDEO/AUDIO input terminals and one group of MONITOR output terminals Auto/manual search OFF timer and ON timer, Auto-Power-Off & blue background display Advanced 6D picture improvement circuit 1.
Congratulations on your purchase of this colour PURE FLAT Hi-Vision Palsonic television receiver. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this receiver. Retain is manual in an easily accessible location for future reference. Contents Main features ................................................................................................ 1 Notes for operation ................................................................
NOTES FOR OPERATION * Do not let the TV set be in standby condition for a long period of time. When it is not in use, please turn off the power supply and remove the power plug. When it is to be left for a prolonged period of time, it is recommended to disconnect the connection to the outdoor aerial, to avoid thunder strike. * Please follow cautions for safety in the TV set instructions, and all warnings and descriptions denoted on the TV set.
Installation and appearance Antenna connection To ensure a bright-coloured and clear picture, you should use an outdoor aerial or CATV cable. If the signals are strong enough, you may use an indoor aerial. Note: In case of using the Twin-lead aerial feeder (300 ) for UHF/VHF aerial, use a 30075 ohm adaptor (not supplied) When using the coaxial cable (not supplied) (75 ) for UHF/VHF aerial, connect the plug into the 75 ohm aerial socket directly.
Appearance Front view POWER SWITCH VOLUME DOWN VOLUME UP CHANNEL DOWN CHANNEL UP MENU TV/AV SYSTEM SELECT (3) Video 3 input terminals {S-VIDEO, VIDEO, AUDIO L/MONO, R} Note: Functions of MENU, TV/AV, SYSTEM, VOL to the remote controller.
The Remote Controller 5
Operation Switching on/off 1. Push the main power switch on, if the set is in Standby mode, the power indicator is red; If there are pictures appearing on the screen, the indicator is yellow. 2. If no picture appears on the screen, push the power button on the remote controller to turn the set on, the indicator turns to yellow. Without using the remote controller, you can push any of the VOL , CH or VIDEO button to turn on the TV.
Presetting the channels There are two ways to preset channels: to preset channels automatically and to preset channels manually. Below we will describe how to preset the channels by making use of the menu. 1. To enter into menu 1.1 Press the MENU button to enter into the main menu. 1.2 Press menu item select button SEARCH. 1.3 Press the SEARCH.
Press the or button to select MANUAL SEARCH 3. MANUAL SEARCH If AUTO-SEARCH cannot preset the desired channels, or you want to preset the desired channels one by one with the preferred channel numbers - please make use of MANUAL SEARCH. SEARCH MANUAL SEARCH AUTO SEARCH 3.1 Press the menu item select button or to select MANUAL SEARCH (the caption on the screen are red). Press the or button to display the menu of MANUAL SEARCH 3.2 Press the or button to enter into the sub-menu of MANUAL SEARCH.
3.5 When you want to store and memorise another channel with another position, repeat steps 3.3, 3,4. MANUAL SEARCH POSITION 14 4. Skip unwanted program numbers After presetting the channels, you can skip unwanted program numbers to select your desired channels. 4.1 Repeat steps 3.1 to 3.3 to select the unwanted program position of the unwanted channels . 4.2 Press the or button to select SKIP. Press the or button to select SKIP ON.
Press the SYS button 6. The setting of colour and sound system 6.1 Press the SYS button, the screen will display colour and sound system. 6.2 If the displaying colour is abnormal, press the or button to select COLOR, then press the or button to select the right colour system. Every time you press or button, the colour system will change in the sequence on the right. AUTO PAL SECAM SYSTEM COLOR AUTO NTSC 4.43 NTSC 3.58 6.
Sound mode selection If the broadcasting TV station is transmitting high quality two-channel digital sound (NICAM) to be added to the already existing FM sound, or transmitting a second FM sound with an identification signal to be added to the already existing first FM sound (IGR), in the upper right corner of the screen will display an indication for several seconds which is listed in the following table. You can press the " " button repeatedly to select sound source.
Picture and sound adjustment Press the | button, you can quickly select two modes of picture and sound quality standard: One is standard mode ( on the screen displays ("STANDARD"); The other is personal select mode (on the screen displays "MEMORY"). 1. Picture adjustment Complete the following steps and you will adjust the picture quality. 1.1 Press the MENU button, on the screen will display the main menu, press the or button to select PICTURE, then press or button to enter into the sub-menu of PICTURE. 1.
2. Sound adjustment Complete the following steps and you will adjust the sound quality. 2.1 Press the MENU button to display the main menu. Press the or button to select SOUND , then press the or button to enter into the sub-menu of SOUND. 2.2 Press the or button to select your required sound adjustment item (the caption on the screen is red), then press the or button to adjust the sound quality.
3. SURROUND SOUND SURROUND OFF Making use of surround sound, you can enjoy the dynamic sound effect that is like being in a music hall. To make use of surround sound, complete steps 2.1, 2.2 to select SURROUND ON, and press the button to select SURROUND then press the or button to adjust its effect. To turn off surround sound, select SURROUND OFF. Press the or button to to select SURROUND ON SURROUND ON Press button to select SURROUND 4. Adjusting the volume and muting the sound.
Other functions 1. ON Timer/OFF Timer With the timer, you can set the TV to turn on/off automatically at a preset time. In the menu of TIMER you can set: CLOCK, ON TIME, OFF TIME. 1.1 OFF TIME With the OFF timer, the TV will automatically switch to standby mode at a preset time. menu of TIMER TIMER OFF TIME OFF 0:00 1.1.1 Press the MENU button to enter into the main menu, press the or button to select TIMER, and press the or button to enter into the sub - menu of TIMER. 1.1.
1.2.3. Pressing the button set the TV into standby mode. At the preset time the TV will automatically turn on to preset channel. To cancel ON TIME, set ON TIME OFF. 1.3 CLOCK The built-in clock employs the 24-hour system. 1.3.1 Do step 1.1.1 to enter into the sub-menu of TIMER. 1.3.2 Press the or button to select CLOCK. Pressing the or button set the present hour and minute. TIMER CLOCK 10:30 Note:To make use of ON TIME and OFF TIME, set the clock firstly and check the correct time. 1.
External Equipment Connections The following describes how to use and connect the TV with other equipment. Refer to the owner's manual of the other equipment to be connected as well. 1. To Connect to AV input You can video equipments such as a VTR and video camera to this TV and enjoy the high quality picture and sound. If your video equipment has an S-VIDEO output terminal, connect it to the S-VIDEO input terminal (special S-VIDEO type) of the unit. If not, connect it to the VIDEO terminal (phono type).
To select the input press the AV button on the remote controller repeatedly until you see the corresponding input indication on the screen. To return to aerial input, press the AV button until it displays programme number, or press direct channel select button or the CH button. TV VIDEO 1 VIDEO 2 VIDEO 3 If the colour of video input is abnormal, the colour system setting may be incorrect.
Troubleshooting Symptoms No power, red indicator is not lit up Poor colour, poor tint Spots appear on the screen Stripes appear on the screen Double images or "ghosts" Snowy picture The remote controller does not work Check the following items . . . . . . . . . . . TV cabinet creaks Be sure the power cord is plugged in Contrast, colour, tint are not correctly adjusted Possible interferences of automobiles, motorcycle, trolley bus, neon lamps, etc.
Specifications Power supply: Power consumption: Dimension (mm): Weight: CRT: AC 240V, 50Hz 200W 926 (W) x 678.5 (H) x 582 (D) 73 kg 80 cm TV system & channel range System VHF PAL-D/K 1-12 PAL-B/G 2-12 PAL-I 2-12 NTSC-M US 2-13 SECAM-B/G 2-12 SECAM-D/K 1-12 Colour system: Sound system : CATV Z1 ~ Z37 X ~ Z + 2, S1 ~ S41 UHF 13-57 21-69 21-69 14-79 21-69 21-69 A-6~A-l,A~W,AA~FFF X ~ Z + 2, S1~S4 PAL/SECAM/4.43NTSC/3.58NTSC NICAM728: B/G 5.5/5.85 I 6.0/6.552 D/K 6.5/5.85 IGR(2 - Carrier) : B/G 5.5/5.
PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www.palsonic.com.