KITCHEN DVD PLAYER TFTV100A USER'S MANUAL
Table of Contents Table of Contents ------------------------------------------------------------Important Safety Instruction -----------------------------------------------FCC Notice --------------------------------------------------------------------Characteristic Features -----------------------------------------------------Disc Information --------------------------------------------------------------Front Panel --------------------------------------------------------------------Rear Panel and Display Pa
Important Safety Information CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Important Safety Instructions Note: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13 14. 15. 16. 17. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use near water. Clean only with dry cloth. Do not block any ventilation openings. Maintain well ventilated conditions around the product. Do not put product on bed, sofa or anything that blocks ventilation. Install in accordance with the manufacturer’s instructions.
Important Safety Information IMPORTANT FOR LASER PRODUCTS 1. CAUTION: LASER RADITATION DO NOT VIEW DIRECTLY WITH OPTICAL INSTUMEMENTS CLASS 1M LASER PRODUCT 2. DANGER: Visible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam. 3. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit. Leave all servicing to qualified service personnel. Region code information: DVD players and discs are coded by region.
FCC Notice Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Characteristic Features Advanced Playing Functions This product incorporates a DVD player, LCD display, TV receiver and radio function in one system. It is designed for convenient use in the kitchen. Please refer to page 30 for the installation instructions. Compatibility Plays: DVD, DVD-RW, CD, CD-R/RW and Picture CD and JPEG discs etc. On-Screen Display Displays your choice of English, French, Spanish, German or Italian.
Disc Information Disc Formats Supported By This Player DISC LOGO DIAMETER PLAYBACK TIME/ PLAYABLE SIDES 133 min (SS-SL) 12cm 242 min (SS-DL) 266 min (DS-SL) 484 min (DS-DL) DVD 41 min (SS-SL) 8cm 75 min (SS-DL) 82 min (DS-SL) 150 min (DS-DL) 12cm 74 min 8cm 20 min CD JPEG 12cm The disc maker specifies the operation of some DVD discs. Please refer to the instruction manual with the disc. Care of Discs Cleaning of Discs Do not touch the playing surface of the disc.
Front Panel Front Panel Drawing 1. POWER Button Press to enter or exit the STANDBY mode. 2. Disc Tray Used to load disc. 3. PLAY/PAUSE Button Press to start or pause playback under DVD mode. 4. STOP Button Press to stop playback under DVD mode. 5. Button Under DVD mode, press once to go to beginning of the current track/chapter. Press twice to go to the previous track/chapter during DVD disc playback. 6. Button Press to go to the next track under DVD mode. 7.
Front Panel 9. Remote Sensor Receives the remote control signal for operation. 10. Display panel Displays the time, status, radio frequency and radio station number. When adjusting volume, the VOL and volume level will be displayed on the display panel for several seconds. 11. SEEK+/ SEEK- Button Under radio mode, press once to fine tune the frequency backward or forward. Press for about 1.5 seconds to search for radio stations forward or backward automatically.
Front Panel Rear Panel Drawing 1. ANT INPUT jack Connected to external antenna to receive the TV program in the TV mode. 2. FM 75 coaxial antenna jack 3. AM antenna jack 4. Left/Right AUDIO input jack Connection for audio input. 5. VIDEO input jack Connection for video input. 6. Direct current 12V input jack Display Panel Drawing 1. FM radio status indicator 2. AM radio status indicator AM time indicator 3. PM time indicator 4. Hour or character indicators 5. Minute or character indicators 6.
Remote Control Preparation Refer to the drawing and remove the battery receptacle. Using the Remote Control Point the remote control towards the main unit when operating. The remote control works best at a distance less than 7m and at an angle of 600 to the front of the unit. No obstacles may stand in the way between the remote control and the infrared sensor. Insert the battery into the receptacle. Make sure the polarity matches the marks inside the component.
Remote Control Remote Control Drawing - 12-
Remote Control 1. POWER Button Press to access or exit the STANDBY mode. 11. /SEEK- Button In the radio mode, press once to fine tune frequency backward. Press for about 1.5 seconds to search radio stations backwards automatically. Under DVD mode, press to activate fast backward playback. 2. SUBTITLE Button Press to select a subtitle language or to turn subtitles off when a DVD with multi-subtitles is playing. 12. /SEEK+ Button In the radio mode, press once to fine tune frequency forward.
Remote Control 19. EJECT Button Press to open or close the disc tray. 21. 0-9 Number Buttons Select numbers by pressing these buttons. 28. TIME Button Press it once to display the time on the display panel in standby status, the time is still displayed on the display panel Press it twice to set the time on the display panel. Use the buttons to select the editing position of hour or minute, use the buttons to adjust the value of the hour or minute upward and downward. 22.
System Connections Do not connect the power cord until all other connections have been made. Each time you restart the unit, it remembers the last function used. Please make all the connections before installing the unit in the kitchen.
System Connections Connecting an Antenna Connect the supplied AM/FM antennas to listen to the radio. In order to improve the signal, move the AM loop antenna away from the system and other equipment. Extend FM antenna fully. Keep the FM antenna as horizontal as possible after connection. When connecting the supplied AM loop antenna, connect the two black cord ends to the AM and ground jacks as shown below.
System Connections Connecting the Power Adapter This unit is powered via the switching power adapter (supplied). See the below figure for details: 1. Connect the AC adapter to the jack marked with "DC 12V IN" on the rear panel of the unit. 2. Plug the three-prong end of the power cord to the grounded electrical socket. 3. When not using the unit, turn off the power of the unit first, and then unplug the power supply to prevent malfunctions.
Radio Function Radio Function Operation Press the AM/FM button on the remote control or SOURCE button on the front panel to enter the AM/FM radio mode. Press and hold the SEEK+/SEEK- button for about 1.5 seconds to start searching forward/backward from the current frequency. Press the SEEK+/SEEK- button again to stop searching. The radio frequency will be displayed on the display panel. The frequency range of FM is from 87.5MHz to 108MHz; frequency range of AM is from 531kHz to 1602kHz.
TV Function Basic Operation Connect the antenna to the antenna jack on the rear panel. After connecting the antenna, connect the power supply cord. If the player is in standby mode, press the POWER button to turn on the power. Press the TV button on the remote control or the SOURCE button on the front panel to shift to TV mode. Press the / (CH+/CH-) buttons to select the desired channel.
TV Function TV System Setup When the button is pressed, the TV system setup menu will appear as below: TV SETUP SYSTEM CHANNEL SKIP SWAP BLUE SCREEN FINE TUNING AUTO MEMORY PAL B/G 001 OFF ___ OFF PICTURE EXIT Use the / (CH+/CH-) buttons to select the item you want to set. Use the / (VOL+/VOL-) buttons to select the item and enter it. First use the / (CH+/CH-) buttons to highlight TV SETUP, and press the button to exit from the TV SETUP menu and press the button to return to the PICTURE setup menu.
TV Function Fine Tuning Use the / (CH+/CH-) buttons to select Fine Tuning, and then press the / (VOL+/VOL-) button to tune forward or backward from the current channel. Auto Memory Use the / (CH+/CH-) buttons to select Auto Memory, press the OK or enter auto memory mode: SEARCHING EXIT button to CH: 001 089.75MHz The auto memory will take a few minutes. The unit will search channels from the lowest channel to the highest channel in the standard channel list.
TV Function Power on To set the playback start time of the signal source, use the number buttons to input the desired start time in sequence of hour, minute. Press the / (VOL+/VOL-) buttons to shift between am and pm. Power off To set the playback end time of the signal source, use the number buttons to input the desired time in sequence of hour, minute. Press the / (VOL+/VOL-) buttons to shift between am and pm. when the playback of the signal source is over, the player will enter standby mode.
AV Function A/V Function The player has an additional A/V input so it can function as a monitor for a DVD player, video cassette player, satellite receiver, video games, etc. When an A/V source is connected, press the A/V button on the remote control to enter SOURCE button on the front panel to enter external input A/V mode.
Play Operation Preparation 1. 2. 3. 4. 5. 6. Install the unit in the kitchen, refer to page 31 for details. After connecting the unit to the AC power, turn on the unit's power by pressing the POWER button. Press the DVD button on the remote control or the SOURCE button on the front panel to shift to DVD mode. Press the EJECT button to open the disc tray. Load the disc with the label facing up. Press the EJECT button again to close the disc tray.
Play Operation CD Playback The player will play all tracks on a CD disc by default. You can use the or number buttons to select a track. / buttons JPEG Playback JPEG is a common picture format that requires small amounts of storage per image and has low loss in resolution. Hundreds of pictures can be stored on a disc in this format. In order to view JPEG photo albums, you can ask your film development company to make a PICTURE CD when they develop your film. Normal Playback Load a JPEG disc.
Playback Functions Stop During playback, press the STOP button once to stop playback of a disc. Press the PLAY button, and the DVD Player will resume playback of the disc from the point where it was stopped. Pause Press the Press the PAUSE button once to pause playback. PLAY button to resume normal playback. Resume Playback Press the STOP button at the point you wish to stop the playback of a disc. The DVD Player will memorise the location where playback of the disc has stopped.
Playback Functions Search By Time During DVD disc playback, press the GOTO button on the remote control once, there will be a menu displayed on the screen. You can set or select items for your preference. Use the / (CH+/CH-) buttons to select items, press the OK button to enter and use the / (CH+/CH-) buttons to select the items. Press the button to return. When select Title or Chapter, use the number buttons to input the desired title or chapter number. Some DVD discs do not support this search function.
System Setup DVD Setup You can customise the set up menu options to your liking. Press the "DVD SETUP" button on the remote control to display the setup menu. The menu will include "General Setup", "Speaker Setup", "Dolby Digital Setup", "Video Setup" and "Preference Setup". Press the direction button ( ) to select a category. All the items in the category will appear on the screen. Press the OK button to enter the category.
System Setup Dolby Digital Setup Dual Mono The function is used to select from Stereo, Left only, Right only, and Mixed mono. Dynamic Use this item to adjust the linear dynamic compression rate to get different signal compression effects. Video Setup Sharpness Use this setting to adjust the sharpness level Brightness Use this setting to adjust the brightness level. Contrast Use this setting to adjust the contrast level.
System Setup Default Reset Use this function to reset the unit to the factory default settings. NOTE: For preference settings, the unit must be in the stop mode. LCD Setup Under DVD mode, press the TV/LCD SETUP button, there will be a menu will be displayed on the screen. PICTURE BRIGHTNESS CONTRAST COLOR LANGUAGE RESET 10 10 10 ENGLISH EXIT Use the / (CH+/CH-) buttons to select the item you want to set (Brightness, Contrast, Colour).
Installing the Unit In Kitchen Installing the unit under a cabinet The player may be installed in the kitchen with or without the spacer. The suggested mounting position of the unit is under a wall cabinet. See the drawing below: NOTE: The dimensions of the player: 355mm x 75mm x 285mm (W/H/D) There should be at least a 35mm distance between the unit and the wall. Installing steps 1. Mark the position of the 4 holes by using the supplied template. Drill four 6.5mm diameter holes.
Installing the Unit In Kitchen 2. 3. If the cabinet door overhangs the shelf and obstructs the unit, adjust the unit or the shelf height for clearance. Install the unit with the supplied mounting screws. Quick hints Since the unit is rather heavy, be careful while doing the fixing work. To reduce the risk of fire, do not place any heating or cooking appliances beneath the unit, especially while the LCD screen is open on viewing.
Troubleshooting SYMPTOM The player cannot play. There is no sound. There is no picture or picture is unsteady. Position of the picture is incorrect. Cannot continue to play and plays a section repeatedly. The remote control does not work. CHECK ITEM Make sure a disc is loaded. Make sure the disc is loaded with label side up. Disc should be clean, not dirty or warped. Player's region code should be the same as the region code of the DVD disc. Make sure water condensation has not occurred.
Specifications LCD screen size 10.2 inches Laser Wavelength Wavelength: 780/650nm Video System PAL Frequency Response 20Hz~20kHz ±2.5dB Audio Signal-to-Noise 85 dB Audio distortion + noise < -70dB (1KHz) Channel Separation > 70dB (1KHz) Dynamic Range >80dB (1KHz) System Radio Frequency Range PLL AM 531~1602kHz FM 87.
PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www.palsonic.com.
