OWNER'S MANUAL 51CM CORDLESS REMOTE LCD TV/ MONITOR MODEL: TFTV515 N111 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www.palsonic.com.
Congratulation on your purchase of this LCD TV We recommend that you read this manual thoroughly before use to fully enjoy the many functions and excellent features of this unit. Keep this manual in an easily accessible location for future reference. Note: Screen displays and illustrations in this manual may differ from the actual model. Contents Index Important Safety Cautions ..................... 1 Identification of controls ........................ 4 Control buttons ....................................
Important Safety Cautions When any unusual situation occurs, turn off the power supply at once and remove the plug from the wall outlet. Contact a qualified service department in your local area. Water and moisture - Do not use this product near water - for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
Important Safety Cautions When relocating the product placed on a trolley, it must be moved with the utmost care. Sudden stops, excessive force and uneven floor surfaces can cause the product to fall from the trolley. The power cords must be routed properly to prevent people from stepping on them or objects from resting on them. Check the cords at the plugs and product. Power supply cords should be routed so that they are not likely to be walked on or snagged by items placed upon or against them.
Important Safety Cautions Important Information Regarding use of Video Games, Computer, captions or other fixed images displays The extended use of a fixed image program material can cause permanent "Shadow Image" on the LCD panel. The background image is viewable on normal programs in the form of stationary fixed images. This type of irreversible LCD panel deterioration can be limited by observing the following steps: * Reduce the Brightness and Contrast settings to a minimum viewing level.
Identification of controls 1. SOURCE The Power Indicator light will glow To access the SOURCE select menu yellow when the set is turned on, 2. MENU and glows red when the set is in Press this button to access the MENU main page. the standby mode. 3. CH +/Change the TV channel. In OSD Menu, press these buttons to choose the OSD items. 4. VOL +/Increase or decrease the sound volume level. In OSD Menu, press these buttons to adjust the value or setting of each item. 5.
Identification of controls (continued) 1. DC POWER input Connect to the DC output of the Power Adapter 2. VGA input / PC- Audio in. Connect to the VGA/audio output 3.5mm jacks on your PC. 3. HDTV input (Y, Pb, Pr, Audio L, R) Connect to the Y/Pb/Pr (or Y/Cb/Cr) and audio output jacks of a Set-Top Box or DVD player. 4. Headphone 3.5mm jack 5. AV outputs (Video, Audio L, R) Connect to the VCR input jacks to record programs. 6.
Remote Control POWER Power on/standby Volume up/down selector; In the menu operation, adjust the selected item Mute CH VOL VOL - + CH EXIT MENU Access the menu Exit the menu C.SYS CLK ZOOM SLP Colour system select Zoom mode selection Setting sleep timer Clock setting AUTO.ADJ Auto correct picture Select picture mode between Bright, Nature, Soft & User Channel up/down selector. In menu operations, used to select item. P.
Preparing the Remote Control Please install the batteries before using the remote control. If the remote control fails to operate the LCD TV functions, replace the batteries in the remote control. 1 Open the battery cover. 2. Insert two size-AAA batteries 3 Replace the cover and slide in reverse until the lock snaps. (Slide the cover while pressing down.) (Place the batteries with their terminals corresponding to the (+ and (-) indications in the battery) compartment.
Installation Install the unit in a room where direct light will not fall upon the screen. Total darkness or a reflection on the picture screen may cause eyestrain. Soft and indirect lighting is recommended for comfortable viewing. Antenna connection Optimum reception of colour requires a good signal and will generally mean that an outdoor aerial must be used. The exact type and position of the aerial will depend upon your particular area.
Installation (continued) Power connection Connect to the DC input socket of the back of the product. Be sure to fully insert plug into the connection and confirm it is secure. 1. Connecting the female plug to the AC socket on AC adapter. 2. Connecting the AC adapter to the DC power input of the set. 3. Connecting the male plug to the wall outlet as illustrated. Note: Always turn off the Power to the LCD TV when connecting the AC adapter.
Installation (continued) Elevation adjustment You can adjust the angle of the LCD TV as follows The elevation can be adjusted from -50 to +100 average.
Installation (continued) 1. Carefully check the terminals for position and type before making any connections. 2. Loose connectors will result in image or colour problems. Make sure that all connectors are securely inserted into their terminals. 3. When connecting an external device, turn off the power to the main unit first tot prevent any possible damage. Connecting the Video/Audio equipment You can connect the unit to a DVD or VCR to enjoy playback with high quality picture and sound.
Installation (continued) The PC input signal connection Connect the VGA (D-sub) input interface on the TV to the output of PC equipment through Min D-sub 15 pin cable as illustrated. For the audio connection, use an audio cord that matches the audio output terminal on the computer. If you select PC signal, please set the input signal source of LCD TV to RGB mode. Audio cable VGA cable (Not supplied) Notes: 1. The native display resolution is 640 x 480.
Installation (continued) AV OUT connection How to connect: Connect the video/audio output terminals on the TV set to the signal input terminals of the VCR equipment or the video/audio input terminals on other TV set through a video/audio cable. Connect the audio output terminals on the TV set to the Audio amplifier through audio cable. How to record the TV program: 1. Connect cables as shown above. 2. Turn on the LCD TV and select source. 3. Turn on the VCR and insert the tape. 4.
Installation (continued) YPbPr input connection Please connect the YPbPr input terminals on the TV set for better picture quality. And connect the audio outputs with the corresponding audio input terminals on the TV set. If you select YPbPr signal, please set the input signal source of the LCD TV to YPbPr mode. Notes: The Y, Pb, Pr outputs on your DVD player are sometimes labelled Y, Cb, Cr. If so, connect the cables to like colours.
Basic Operations Turning on POWER 1 Connect the power correctly, then the red indicator lights up and the unit is in STANDBY mode. 2 Press the POWER ( ) button on the remote control or on the unit to turn on the TV set. The indicator will turn to yellow. CH VOL VOL - + CH EXIT MENU C.SYS AUTO.ADJ 1 CLK ZOOM P.M Turning off 1 With the power on, press the POWER ( ) button to turn off the TV and the TV is in STANDBY mode, the indicator will turn to red.
Main On-Screen-Display (OSD) introduction 1 2 3 4 5 6 Press MENU button to display menu screen. Press VOL+/- to select the menu. Press CH to access the menu. Press CH to select the item. Press VOL+/- to adjust the item. Press EXIT button repeatedly to exit the menu. TV/AV/S-VIDEO MODE YPbPr / RGB MODE Picture Setting Menu Picture Setting Menu brightness 50 contrast 50 color 16 sharpness 32 tint 0 System Position Menu 6 scaler mode fill all color sys. Auto sound sys.
Operations Channel Setting There are two ways to preset channels: to preset channels automatically and to preset channels manually. Below we will describe how to preset the channels by making use of the menu. POWER Auto Search 1 Access Channel Setting menu. CH - + CH EXIT MENU C.SYS skip VOL VOL CLK ZOOM SLP channel number 2 Press CH button repeatedly to highlight auto search item. off 1 P.M auto search fine tune channel edit 2 VHFH Searching 20 Search.
Operations Channel Setting To skip unnecessary channel After presetting the channels, you can skip unnecessary channels so that only the channels you want to watch are selected when you press the CH to change channels. POWER 1 Select the channel number which you want to skip using the keypad. 2 Access the Channel Setting menu. 3 Press CH item. CH VOL VOL - + CH EXIT MENU C.SYS AUTO.ADJ CLK ZOOM P.M SLP 4 DSP to select skip channel number skip Press VOL+/- to select on.
Operations Channel Setting Channel edit You can edit the channel programs in your favourite order. POWER CH 1 Access the Channel Setting menu. 2 Press CH to select channel edit. Press VOL+/- to enter into the sub-menu. VOL VOL - + CH EXIT MENU C.SYS ZOOM CLK AUTO.ADJ P.M DSP 2 3 4 5 6 7 8 9 0 -/-- skip off 9 on manual search auto search fine tune 3 Press CH to select current channel, press VOL+/- to select a current channel number.
Operations Selecting channel Using Keypad buttons 1 POWER Input the channel using the 0-9 number button, then wait for about 2 seconds. CH 2 To select two-digit channel numbers: VOL VOL - Press -/-- button to display --, then input the channel using the 0-9 number button. + CH EXIT MENU C.SYS To select one-digit channel numbers: CLK ZOOM SLP 3 To select three-digit channel numbers: Press -/-- button to display ---, then input the channel using the 09 number button. AUTO.ADJ P.
Operations Picture adjustment 1 Access Picture Setting menu by pressing MENU button. 2 Press CH to select the item that you want to adjust. POWER 3 CH VOL VOL - + brightness 50 contrast 50 color 16 sharpness 32 tint 0 Press VOL+/- to adjust selected item. CH EXIT MENU C.SYS ZOOM CLK AUTO.ADJ P.
Operations Audio Setting Adjusting volume POWER CH VOL VOL - + CH EXIT MENU C.SYS ZOOM CLK AUTO.ADJ P.M DSP 1 4 2 SLP Press VOL+/- to adjust volume. Press VOL+ button, the volume increases. Press VOL- button, the volume decreases. (Range: 0-100) Muting the sound You can press the button on the remote control to mute the sound. Press the button again to restore. You can also press VOL+ to restore the sound. Making use of the Audio Setting Menu 3 1 Access Audio Setting menu.
Operations System Setting 1 Access the System Setting menu. 2 Press CH to select the item that you want to adjust. POWER 3 Press VOL+/- to adjust selected item. blue screen on backlight 6 scaler mode fill all color sys. Auto sound sys. I sleep time 10 minutes CH VOL VOL - + CH EXIT MENU C.SYS CLK ZOOM SLP Function Item If you select on. the screen will display Blue Screen blue background when there is no signal (in TV, AV, SVIDEO mode).
Operations OSD Setting Setting the language of the menu POWER 1 Access the OSD Setting menu. 2 Press CH to select the language item. Press VOL+/- to select an OSD language. If select English, then the OSD is displayed in English. 3 CH VOL VOL - language English OSD position OSD background opaque translucent OSD timeout 30 seconds language English + CH EXIT MENU Setting the position of the menu C.SYS AUTO.ADJ CLK ZOOM P.M SLP DSP 1 Access the OSD Setting menu.
Operations Timer Setting Using Sleep button POWER CH VOL VOL - + Press SLP button to display sleep time menu bar. Press CH or VOL+/- repeatedly to set sleep time between: 0, 10, 20, 30, 60, 90, 120, 180, 240 minutes. If you select 0 minute, the sleep timer function is turned off. CH EXIT MENU C.SYS ZOOM CLK AUTO.ADJ P.M DSP SLP 1 2 3 4 5 6 7 8 9 0 -/-- Press the SLP button again to exit the menu. Using Clock button 1 Press CLK button, the current time menu bar appears.
Operations in RGB/YPbPr mode Select RGB/YPbPr mode 1 Press the SOURCE button on the unit or button on the remote control. The screen displays the menu shown as right. 2 Press CH to highlight the RGB or YPbPr item. Press VOL+/- or wait about 4 seconds and the signal source is selected. POWER CH VOL VOL - + CH EXIT MENU C.SYS CLK ZOOM SLP PC signal format AUTO.ADJ 1 P.M Connect VGA input and be sure that there is VGA input signal. The signal format should be set to: 640 x 480@60Hz.
Operations in RGB/YPbPr mode (continued) Picture Settings Adjusting Brightness/Contrast POWER CH VOL VOL - 1 Access the Picture Setting menu. 2 Press CH to select brightness or contrast item. 3 + brightness 50 contrast 60 color temp 5000K 7300K 9300K user Press VOL+/- to adjust the selected item. customer temp setting CH EXIT MENU Function Item C.SYS CLK ZOOM SLP Notes brightness Adjust the brightness of the picture.
Troubleshooting Before calling for service personnel, please check the following chart for a possible cause to the trouble you are experiencing. Symptoms Check item Ghost or double images This may be caused by obstruction to the antenna due to high rise buildings or hills. Using a highly directional antenna may improve the picture. No power Check that the AC power cord is plugged into the mains socket. Unplug the power cord, wait for 60 seconds.
Specification Power Supply for AC adaptor: 100-240V 50/60Hz Power Consumption: 60W Resolution: 640 x 480 Pixel Pitch: 0.2125mm x 0.6375mm Brightness: 450 nit Contrast: 500:1 Viewing angle: 1600/1400 Dimensions (mm): 637(W) x 210(D) x 447(H) (with stand) Weight (kg): 10 Screen: 51cm TV system & channel coverage.
PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 604-L20H33-08 Ver1.