OWNER'S MANUAL 127CM CORDLESS REMOTE PLASMA TELEVISION & MONITOR MODEL: PDP 5000 N111 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www.palsonic.com.
Table of Contents Table of Contents ........................................... Important Safety Precautions ......................... Preparations ................................................... Using the Remote Control ........................ Batteries for the Remote Control ............. Power connection .................................... Speaker connection ................................. Antenna Connection ................................ Identification of Controls .............................
Important Safety Precautions Electrical energy can perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product.
Important Safety Precautions (continued) 12. Stand---Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. Do not place the product on an unstable trolley, stand, tripod or table. Placing the product on an unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to the product. When mounting the product on a wall, be sure to follow the manufacturer's instructions.
Important Safety Precautions (continued) 22. Power source---This product is intended to be supplied by a listed power supply indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system.
Preparations Using the Remote Control Use the remote control by pointing it towards the remote sensor window of the set. Objects between the remote control and sensor window may prevent proper operation. Note: the illustration is for your reference only, the remote sensor may locate differently with different model. Cautions regarding use of remote control Do not expose the remote control to shock. In addition, do not expose the remote control to liquids, and do not place in an area with high humidity.
Preparations (continued) Power connection Household power outlet Plug into AC outlet AC-INPUT AC cord 1. Connecting the female plug to the AC socket on the unit. 2. Connecting the male plug to the wall outlet as illustrated. Note: This product should be operated only from the type of power source indicated on the marking label. Always unplug the AC cord from power outlet when not using for a long period of time. The illustration of the AC plug is for your reference only depending on your area.
Preparations (continued) Antenna Connection INSTALL the unit in a room where direct light will not fall upon the screen. Total darkness or a reflection on the picture screen may cause eyestrain. Soft and indirect lighting is recommended for comfortable viewing. Optimum reception of colour requires a good signal and will generally mean that an outdoor aerial must be used. The exact type and position of the aerial will depend upon your particular area.
Identification of Controls Main unit (front view) REMOTE SENSOR POWER INDICATOR A blue indicator lights when the power is on and a red indicator lights when in the standby mode. BOTTOM VIEW SOURCE SELECT POWER SWITCH CHANNEL MENU DOWN/UP VOLUME DOWN/UP 1. SOURCE Press this button to display SOURCE select menu. 2. MENU Press this button to access the MENU main page. 3. Volume Press the VOL or VOL button to directly increase or decrease the sound volume level.
Identification of Controls (continued) Main unit (rear view) AC power input socket Speaker output jacks CONTROL DVI COMPONENT INPUT 1 D-SUB COMPONENT INPUT 2 HEADPHONE AV OUTPUT AV INPUT 7 8 RF SVHS BOTTOM VIEW 1 2 3 5 4 6 1. RS232 terminal For service use only. The user cannot operate the unit through the RS232 terminals. 2. DVI input /Audio in Receives the digital video/audio signals from a set top box or PC. 3. VGA input /Audio in Connect to the VGA/audio output jacks on your PC. 4.
Identification of Controls (continued) Remote Control 1. POWER Turn the unit on or off 2. CH , VOL+/Use to switch channels or adjust volume; In MENU operation, use CH to select menu item and VOL+/to adjust selected item. 3. MENU To access the MENU main page 4. STILL To freeze current picture 5. ZOOM To go into ZOOM or PAN mode 6. S.M To access sound mode select menu 7. PM To access picture mode select menu 8. 0~9 digit buttons Direct channel select 9. SOURCE To access source select menu 10.
Identifications of Controls (continued) Remote Control 17. MODE To access screen layout select menu 18. PIP display To activate picture in picture 19. POS To access PIP frame position select menu 20. SIZE To access PIP frame size adjusting menu 21. SPEAKER In multi-picture mode, press this button to output the sound of the selected picture frame from speaker 22. SWAP To exchange PIP and MAIN PICTURE source 23.
Connections Cautions before connecting Carefully check the terminals for position and type before making any connections. The illustration of the external equipment may be different depending on your model. Loose connectors can result in image or colour problems. Make sure that all connectors are securely inserted into their terminals. Refer to the operating manual of the external device as well. When connecting an external device, turn the power off on the panel to avoid any issues.
Connections (continued) Connect a Camcorder CONTROL DVI D-SUB COMPONENT INPUT 1 COMPONENT INPUT 2 HEADPHONE AV OUTPUT AV INPUT RF BOTTOM VIEW Yellow (VIDEO) White (AUDIO L) Red (AUDIO R) Video cable Audio cable OUT IN How to connect: Connect the Audio/Video cables between the Audio (L/R)/Video jacks on the unit and camcorder. To playback Camcorder 1. Turn on your PDP TV, press SOURCE button on the remote control. 2. Press VOL+/- to select AV (VIDEO) and press ENTER to confirm. 3.
Connections (continued) Connect a DVD Player CONTROL DVI D-SUB COMPONENT INPUT 1 COMPONENT INPUT 2 HEADPHONE AV OUTPUT AV INPUT RF BOTTOM VIEW white (audio L) red (audio R, Pr/Cr) Green (Y) Video cable Audio cable Blue (Pb/Cb) DVD Player Rear of the DVD player How to connect a DVD Player using Component Video Connections: Connect the Video cable between the Y, Cb, Cr input jacks on the unit and Y, Cb, Cr output jacks on the DVD player.
Connections (continued) Connect a DTV receiver CONTROL DVI D-SUB COMPONENT INPUT 1 COMPONENT INPUT 2 HEADPHONE AV OUTPUT AV INPUT RF SVHS BOTTOM VIEW white (audio L) red (audio R, Pr/Cr) Green (Y) Video cable Audio cable Blue (Pb/Cb) DTV Receiver Rear of the DTV receiver How to connect: Connect the cable or antenna to the antenna input jack on the DTV receiver. Connect the Video cable between the Y, Pb, Pr input jacks on the unit and Y, Pb, Pr output jacks on the DTV receiver.
Connections (continued) Connect a PC CONTROL DVI D-SUB COMPONENT INPUT 1 COMPONENT INPUT 2 HEADPHONE AV OUTPUT AV INPUT RF SVHS BOTTOM VIEW or DVI cable VGA cable Audio cable PC How to connect: Connect a VGA (or DVI) cable between the VGA (or DVI) jack on the PC and the VGA (or DVI) input jack on the unit. Connect an Audio cable between the AUDIO output on the PC and AUDIO input jack on the unit.
Connections (continued) Connect a VCR (for recording) or external amplifier CONTROL DVI D-SUB COMPONENT INPUT 1 COMPONENT INPUT 2 HEADPHONE AV OUTPUT AV INPUT RF BOTTOM VIEW Yellow (VIDEO) White (AUDIO L) Red (AUDIO R) Audio cable Audio cable Video cable VCR for recording To Audio inputs External Amplifier Rear of the VCR How to connect: Connect the Audio/Video cables between the Audio (L/R)/Video jacks on the unit and VCR.
Turning the Unit On and Off Turning the Unit On and Off Turning On Insert the power cord into the wall outlet. Press the Power Switch on the unit. Press the Power button on the remote control. The unit will be turned on and you will be ready to use it's features. Turning Off With the power on, Press the Power button on the remote control to turn off the unit temporarily. If you want to cut off the power completely, press the power switch on the unit directly.
Memorising the Channels Your PDP TV can memorise and store all of the available channels. After the available channels are memorised, use CH to scan through the available stations. Storing Channels in Memory Automatically 1 Press MENU to display the menu main page. 2 Press VOL+/- repeatedly to display options menu page. 3 Press CH options tv tuner to select tv tuner item. select to activate tuner menu 4 Press VOL+ or ENTER to access the submenu.
Memorising the Channels (continued) Setting Auto Fine Tune (AFT) 1 Repeat steps 1~4 in [Storing Channels in Memory Automatically] to display search menu page. search 2 Press CH 3 Press VOL+/- to select on or off. When the AFT is set to On, the unit will automatically tune the program frequency to provide the best possible picture and sound. repeatedly to select auto fine tune item.
Basic Operations Changing Channels Using the Channel Buttons (CH or CH ) Press the CH or CH to change channels. When you press the CH or CH , the unit changes channels in sequence. You will see all the channels that the unit has memorised. You will not see channels that were erased, not memorised or unavailable. Direct Accessing Channels Press the number buttons to go directly to a channel.
Basic Operations (continued) Select input source signal 1 Press the SOURCE 2 Press VOL+ or VOL- to select a desired input channel. 3 Press ENTER to confirm and the unit display signal from the selected input channel. button to access source menu. source A D H1 H2 C1 C2 AV TV A--------VGA, select signal from VGA (5-pin D-sub) terminals. D--------DVI, select signal from DVI terminals. H1------YPbPr1, select signal from YPbPr1 terminals. H2------YPbPr2, select signal from YPbPr2 terminals.
Setting Channel Options Editing Channel Label 1 Press MENU to display the menu main page. options 2 Press VOL+/- repeatedly to display options menu page. 3 Press CH 4 tv tuner to select tv tuner item. select to activate tuner menu Press VOL+ to enter. 5 Press VOL+ again to display channel menu page. channel edit labels 6 Press CH to select edit labels item. 7 Press VOL+/- to enter into channel label editing mode. select to edit channel labels 8 Use CH to select a channel you want add label to.
Setting Picture Customising the Picture 1 Press MENU to display the menu main page. If the picture menu does not display, press VOL+/- repeatedly to display picture menu page. 2 3 Press VOL+/- to adjust the value of the item. 4 Press MENU to exit. Press CH to select the item you wish to change. picture brightness contrast sharpness colour tint 50 50 50 50 12 down for picture settings for current window Note: The tint function is for NTSC only. Using the Preset Picture Mode 1 Press P.
Setting System Setting the Menu Background 1 Press MENU to display the menu main page. 2 Press VOL+/- to display settings menu page. 3 Press CH to select menu background item. 4 Press VOL+/- to select opaque or translucent. settings opaque English AUTO BG menu background language video format audio format right/left to change menu background Setting Colour and Sound System 1 Press MENU to display the menu main page. 2 Press VOL+/- to display settings menu page.
Changing Screen Options Changing the Scaling mode of Image 1 Press MENU to display the menu main page. window image size h position v position freeze window digital pan and zoom 2 Press VOL+/- to display window menu page. 3 Press CH to select image size item. 4 Press VOL+/- to select a proper image size. The image size can be selected between: fill all, normal, wide and zoom.
Changing Screen Options (continued) Changing the Position of the Image The unit allows you to adjust the position of the image if it is not well-aligned. 1 Press MENU to display the menu main page. 2 Press VOL+/- to display window menu page. window 3 Press CH 4 Press VOL+/- to adjust until the picture is well-aligned. repeatedly to select h position or v position item.
Setting Sound Using the Preset Audio Mode 1 Press MENU to display the menu main page. audio 2 3 4 audio mode treble bass balance headphone auto volume Press VOL+/- to display audio menu page. Press CH to select Audio mode item. Press VOL+/- to select a desired Audio mode. Note: You can not access the treble and bass item unless the Audio mode is set to User. cinema 50 50 50 50 off on right/left to set audio mode Customising the Sound 1 Press MENU to display the menu main page.
Setting Sound (continued) Using the Auto Volume Each broadcasting station has its own signal conditions, which can make it necessary to adjust the volume every time the channel is changed. "Auto volume" lets you automatically adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low. 1 Press MENU to display the menu main page. 2 Press VOL+/- to display audio menu page.
Changing Screen Layout Selecting Screen Layout Using the Layout Menu 1 Press MENU to display the menu main page. 2 Press VOL+/- to display layout menu page. 3 Press CH 4 Press VOL+ or ENTER to confirm. layout full screen pip split screen pop3 grid to select item. down for current screen layout options Using the MODE button 1 Press the MODE button to display the screen layout select menu. 2 Press VOL+/- to select item. 3 Press ENTER to confirm. 4 Press MENU to exit.
Changing Screen Layout (continued) PIP When this item is selected, one main frame and one PIP frame display on the screen at the same time. Main Frame PIP Frame Split Screen When this item is selected, the screen will be split into two frames. Main Frame Split Frame POP3 2 When this item is selected, one main frame and three scanning frames display on the screen. Scanning Frame Main Frame 3 4 Grid 1 2 4 5 6 7 8 9 When this item is selected, the screen displays 9 scanning frames.
PIP Operations Viewing the Picture-in-Picture This unit includes a two-tuner Picture-in-Picture (PIP) feature. This allows you to watch two (2) live broadcasts at the same time with or without an external video source such as a VCR, cable box, etc. 1 Press MENU to display the menu main page. 2 Press VOL+/- to display layout menu page. 3 Press CH 4 Press VOL+ or ENTER to display pip frame. The screen displays one main frame and one PIP frame.
PIP Operations (continued) Changing the Position of the PIP Frame the PIP frame displaying, press MENU to display the menu 1 With main page. 2 Press VOL+/- to display window menu page. 3 Press CH repeatedly to select pip position item. 4 Press VOL+/- to select a desired position for the PIP frame.
Adjustment in PC (VGA) Mode With working in VGA mode, this unit allows you to perform many adjustments. Adjusting Picture picture 1 Press MENU to display the menu main page. If the picture menu does not display, press VOL+/- repeatedly to display picture menu page. 2 Press CH 3 Press VOL+/- to adjust the value of the item. brightness contrast phase frequency 50 50 50 50 to select brightness or contrast item.
Adjustments in PC (VGA) Mode (continued) Changing the Scaling mode of Image 1 Press MENU to display the menu main page. 2 Press VOL+/- to display window menu page. 3 Press CH 4 Press VOL+/- to select fill all or Normal. 5 Press MENU to exit. window image size h position v position off freeze window digital pan and zoom to select image size item.
Adjustments in YPbPr Mode Changing the Scaling mode of Image 1 Press MENU to display the menu main page. 2 Press VOL+/- to display window menu page. 3 Press CH window image size h position v position off freeze window digital pan and zoom h wide v high to select image size item. 4 Press VOL+/- to select a desired scaling mode. 5 Press MENU to exit.
Troubleshooting Before calling for repair service, check the following items for possible remedies to an encountered symptom. Symptoms Check item "Ghost" or double images This may be caused by obstruction to the antenna due to high rise buildings or hills. Using a highly directional antenna may improve the picture. No power Check that the AC power cord is plugged into the mains socket. Unplug the power cord, wait for 60 seconds. Then reinsert plug into the mains socket and turn on the unit again.
Specifications Type PDP TV Display Size diagonal 127cm Display Feature Resolution 1366 X 768 Pixel Pitch 0.81 X 0.
Dimensional Drawings 82.5 832 744 1222 1429 (Unit: mm) 777 Design and specifications are subject to change without notice.
PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www.palsonic.com.
