PYRAMID PATIO HEATER INSTRUCTION MANUAL Keep the instructions for future reference
PLEASE READ THE FOLLOWING SAFETYADVICE PRIOR TO THE OPERATION OF THIS HEATER If you smell gas: 1. Switch off the gas regulator. 2. Extinguish any open flame. 3. If the smell continues immediately call your gas supplier or your fire department. 4. Do not store or use flammable liquids in the vicinity of this heater. 5. Any gas cylinders not connected for use shall not be stored in the vicinity of this heater. For use outdoors or in areas that have ample ventilation.
BITTE LESEN SIE DIE FOLGENDE SICHERHEIT HINWEIS VOR DEM BETRIEB DIESES HEIZUNG VEUILLEZ LIRE LES CONSIGNES DE SÉCURITÉ SUIVANTES AVIS AVANT LE FONCTIONNEMENT DE CE CHAUFFE-EAU Wenn Sie Gas riechen: Si vous sentez du gaz: 1. Schalten Sie den Gasregler aus. 2. Löschen Sie alle offenen Flammen. 3. Wenn der Geruch sofort anhält, wenden Sie sich an Ihren Gasversorger oder Ihre Feuerwehr. 4. Lagern oder verwenden Sie keine brennbaren Flüssigkeiten in der Nähe dieses Heizgeräts. 5.
SI PREGA DI LEGGERE LA SEGUENTE SICUREZZA CONSIGLI PRIMA DELL'OPERAZIONE DI QUESTO RISCALDATORE POR FAVOR LEA LAS SIGUIENTES SEGURIDAD ASESORAMIENTO ANTES DE LA OPERACIÓN DE ESTE CALENTADOR Se senti odore di gas: Si huele a gas: 1. Spegnere il regolatore del gas. 2. Spegnere qualsiasi fiamma libera. 3. Se l'odore persiste, chiamare immediatamente il fornitore del gas o i vigili del fuoco. 4. Non conservare o utilizzare liquidi infiammabili nelle vicinanze di questo riscaldatore. 5.
TABLE OF CONTENTS Safety Precautions …………………………………………………… 7 Heater Stand and Location …………………………………………… 9 Gas Requirements …………………………………………………… 9 Leak Test ………………………………………………………………10 Operation and Storage …………………………………………………11 Cleaning and Care ……………………………………………………12 Parts and Specifications ………………………………………………12 Construction and Characteristics …………………………………… 13 Specification …………………………………………………………… 13 Assembly Parts ……………………………………………………… 14 Assembly Procedure…………………………………………………… 16 Troubleshooting ……………………
HEATER STAND AND LOCATION The heater is primarily for outdoor use only. Always ensure that adequate fresh air ventilation is provided. Always maintain proper clearance to non protected combustible materials i.e. top 100 cm and sides 100 cm minimum.
Leak Test OPERATION AND STORAGE Gas hose connections on the heater are leak tested at the factory prior to shipment. A complete gas leak check must be performed at the installation site due to possible mishandling during the transit process. Off: the heater stop work Hi: maximum temperature position Lo: minimum temperature position Leak testing: Do not smoke while performing this test, and remove all sources of ignition. A full gas cylinder is required.
CLEANING AND CARE • • • CONSTRUCTION AND CHARACTERISTICS Wipe off surfaces with soft, moist cloth. Do not clean the heater with cleaning products that are combustible or corrosive. Remove debris and insects from the burner periodically to keep it clean and safe for use. Cover the burner unit with the optional protective cover when the heater is not in use. • Transportable terrace/garden heater with cylinder housing.
ASSEMBLY PARTS Hardware Contents Tools needed: • • AA Philips screwdriver w/ medium blade Spray bottle of soap solution for leakage test A Reflector B Top Plate Assy C Glass Tube D Upper Support E Protective Guard F Black Silicone Ring Control Box Assy K G Side Panel Lower Support L H Front Panel Wheel Assembly M I Gas Hose & Regulator Bottom Plate N PART A B C D E F G H I J K GG CC M6 nut Qty.4 Bolt M6x10 Qty. 4 Parts List: Middle Plate BB HH Fixing Bracket Qty.
Assembly Procedure 1.Assemble the wheel assembly (M) to the bottom plate (N) using 4pcs bolt M6x10 (AA) and 4pcs M6 nut (BB). 3. Insert upper support (D) to lower support (L) using 8pcs screw M5x10. Assemble top plate assy (B) to upper support (D) using 8pcs screw 3/16”. 1 3 HH Hardware Used AA Bolt M6x10 x4 BB M6 nut x4 CC screw M5x10 x8 HH Screw 3/16” x8 M BB 2 2-1. Unscrew the ignition, load small battery, tighten the ignition. 2-2.
5. Carefully install the glass tube (C) by lifting up and inserting through the center hole in the top plate assy (B). Ensure the black silicone ring (F) is attached to the lower edge of the glass tube (C) as illustrated. Slide the glass tube (C) through the hole of the lower plate cover and onto the middle plate (J). Check and ensure that the glass tube (C) is positioned properly and is completely covering the center hole of the middle plate(J). 5 7.
9 9 LEAK TEST Please ensure you follow the procedure on page 7 before operating the heater.
