Installation Guide Home Network System Water Leak Sensor Model No. KX-HNS103 Thank you for purchasing a Panasonic product. This document explains how to install the water leak sensor properly. For details about how to use the system, refer to the User’s Guide (page 15). Please read this document before using the unit and save it for future reference. For assistance, please contact us at 1-800-272-7033 or visit our Web site: www.panasonic.com/support for customers in the U.S.A. or Puerto Rico.
Table of Contents Introduction Accessory information ...............3 Important Information About this system ......................4 For your safety ...........................4 Important safety instructions ......5 For best performance ................5 Other information .......................6 Setup Part names and functions ..........8 About the LED indicator .............8 Setup overview ..........................8 Inserting the battery ...................9 Registering the sensor ...............
Introduction Accessory information Supplied accessories No. Accessory item/Part number A Battery*1 B Wall mounting adaptors*2 2 C Wall mounting screws (25 mm (1 inch))*3/XTB4+25AVW 3 *1 Quantity 1 When replacing the battery, see “Power source” of “Specifications”, page 16 for battery information.
Important Information About this system This system is an auxiliary system; it is not designed to provide complete protection from property loss. Panasonic will not be held responsible in the event that property loss occurs while this system is in operation. R Keep small parts (screws, etc.) out of the reach of children. There is a risk of swallowing. In the event they are swallowed, seek medical advice immediately. Operating safeguards R Do not disassemble the product.
Important Information thoroughly with water, and then consult a doctor. CAUTION Installation and location R Although this unit conforms to the IPX4*1 specification, do not intentionally expose it to water. *1 IPX4 indicates that the unit is not harmfully affected by water sprayed on it from any direction. CR Lithium battery R Use only the battery noted on page 3. R Insert the battery correctly.
Important Information R If the reception for a hub location is not satisfactory, move the hub to another location for better reception. Environment R Keep the product away from electrical noise generating devices, such as fluorescent lamps and motors. R The product should be kept free from excessive smoke, dust, high temperature, and vibration. R The product should not be exposed to direct sunlight. R Do not place heavy objects on top of the product.
Important Information Notice For assistance, please visit www.panasonic.com/support HNS103_(en_en)_1120_ver.010.
Setup Part names and functions n Main unit About the LED indicator N and check the You can press M LED indicator to confirm the sensor’s status. A B C n Probe unit Indicator Status Green, lit No water detected Red, lit Water detected Red, blinking Sensor is out of range of the hub Green, blinking Registration mode (You pressed and held N) M Off No battery power Note: R The LED indicator does not indicate sensor status if the sensor has not been registered (page 9).
Setup 5 desired installation area is suitable to proper operation. Installation Install the sensor in the desired location. Inserting the battery R USE ONLY a CR2 Lithium battery. R Confirm the polarities ( , ). 1 Remove the main unit cover. R Lift from the indented area (A) and open the main unit cover (B). 2 2 This procedure is not required for devices that were included as part of a bundle. Before you can use the sensor, it must be registered to the hub. If you purchased devices separately (i.e.
Setup information, refer to the User’s Guide (page 15). Information about sensor features Please read the following information before deciding where to install the sensor. Note: R The sensor is not designed to be used in situations that require high reliability. We do not recommend use of the sensor in these situations. R Panasonic takes no responsibility for any injury or damage caused by the use of this product.
Setup Installation When the metal probes on the probe unit come in to contact with water, a small amount of electrical charge flows between the probes, which the main unit recognizes as a water leak. Note: R When installing, make sure the battery is inserted properly and the unit cover is completely closed. R When installing on a wooden surface, use the included wall mounting adaptors. When securing the wall mounting adaptors to the wall, use screws (not double-sided tape).
Setup Securing with the wall mounting adaptors 1 Use screws to attach the wall mounting adaptors to the wall. n Main unit 1 Screws 2 86.2 mm (3 25/64 inches) n Probe unit 1 Screws 1 2 1 1 2 Affix double-sided tape to the main unit and probe unit. 3 Insert the main unit and the probe unit into the wall mounting adaptors, and press firmly on each unit to ensure solid adhesion to the installation surface. 12 For assistance, please visit www.panasonic.com/support HNS103_(en_en)_1120_ver.010.
Setup Securing with double-sided tape only Note: R Make sure the surfaces of the main unit, probe unit, and the installation area are clean and dry before applying double-sided tape. 1 Affix double-sided tape to the main unit and probe unit. 2 Attach the main unit and the probe unit to the installation surface, and press firmly on each unit to ensure solid adhesion to the installation surface. For assistance, please visit www.panasonic.com/support HNS103_(en_en)_1120_ver.010.
Setup Removing from the wall n Removing from the wall mounting adaptors 1 Insert a flat screwdriver into the notches on the wall mounting adaptors, and carefully pry away the main unit and probe unit. 2 Remove the screws that secure the wall mounting adaptors to the wall. n Removing when secured with double-sided tape only 1 Tie a piece of thread to two sticks, screwdrivers, etc. 2 Pull the thread tight and use it to cut the double-sided tape, and then remove any excess tape.
Appendix Features available when using the [Home Network] app Some of the sensor’s features that are available when using the [Home Network] app are listed below. For more information, refer to the User’s Guide (page 15). – Alarm system You can use the app to arm and disarm the alarm system, confirm the current status of the sensor, and view a log of previous events.
Appendix Specifications R Standards DECT 6.0 (Digital Enhanced Cordless Telecommunications 6.0) R Frequency range DECT: 1.92 GHz – 1.93 GHz R RF transmission power DECT: 115 mW (max.) R Power source Lithium battery CR2 (1 ´ 3.0 V, 850 mAh) R Operating conditions 0 °C – 40 °C (32 °F – 104 °F) R Sensor detection method xx R Battery life Approx.
Appendix FCC and other information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this device.
Appendix Customer services Customer Services Directory (United States and Puerto Rico) Obtain Product Information and Operating Assistance; locate your nearest Dealer or Service Center; purchase Parts and Accessories; or make Customer Service and Literature requests by visiting our Web Site at: www.panasonic.com/support or, contact us via the web at: www.panasonic.com/contactinfo You may also contact us directly at: 1-800-272-7033, Monday - Friday 9 am to 9 pm; Saturday - Sunday 10 am to 7 pm, EST.
Appendix Warranty (For United States and Puerto Rico) Panasonic Home Network System Products Limited Warranty Limited Warranty Coverage If your product does not work properly because of a defect in materials or workmanship, Panasonic Corporation of North America (referred to as “the warrantor”) will, for the length of the period indicated on the chart below, which starts with the date of original purchase (“Limited Warranty period”), at its option either (a) repair your product with new or refurbished par
Appendix Limited Warranty Limits And Exclusions This Limited Warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage.
Notes 21 HNS103_(en_en)_1120_ver.010.
Notes 22 HNS103_(en_en)_1120_ver.010.
Notes 23 HNS103_(en_en)_1120_ver.010.
IMPORTANT! If your product is not working properly. . . 1 Use CR2 Lithium battery. 2 Use the Home Network app to access the User’s Guide and refer to the Troubleshooting section. Visit our Web site: www.panasonic.com/support LFAQ and troubleshooting hints are available. For your future reference We recommend keeping a record of the following information to assist with any repair under warranty. Serial No.