SAMPLE (2nd draft) This is NOT the final draft. Wireless Communication System Center Module Operating Instructions Model No. WX-CC2010 Series Digital Technology WX-CC 2010 TRAN SCEIV MONIT ER OR POWER VEHICLE PRESENT A B WX -C T2 02 0 Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not use near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
CONTENTS IMPORTANT SAFETY INSTRUCTIONS ...................................................................................................... 3 PREFACE..................................................................................................................................................... 5 PRECAUTIONS............................................................................................................................................
PREFACE Panasonic WX-CC2010 Center Module is designed for Panasonic Wireless Communication System, which is used with drive-through menu boards, etc. The system operates on UHF frequencies, and offers multi-channel flexibility making use of the PLL (Phase Locked Loop) technology. FEATURES • A remote speaker can be added to the system. • The order taker unit and all-in-one headset are designed to facilitate the battery installation.
PRECAUTIONS This center module is a sensitive device and should be regarded as such. If handled carelessly, the hazard of electric shock may exist. 7. Replace a missing microphone cover and ear speaker cover of the headset with a new one to prevent distortion or loss of audio. In order to utilize the instrument to its fullest potential, please consider the following precautions. 8. Repair or replace any defective components. 1. Handle the equipment with care.
PANASONIC WX-CC2010 SERIES SYSTEM PARTS AND ACCESSORIES Note: Illustrations may differ from actual products.
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ■ WX-CC2010 Center Module q AUX IN TALK PAGE BEEP REMOTE AUX IN SEL TALK MONITOR OFF OFF OFF OFF ON ON ON ON LINE G/MIC ON OFF WX-CC w CHANNEL CONTINUES USA/CANADA T/B TBC1 LEVEL TBC2 DNR1 DNR DNR2 EFFECT DNR3 A OFF USA OFF B ON CND ON OFF OFF ON ON OFF ON OFF ON e r VEHICLE DETECTOR t POWER CIRCUT PROTECTOR ON NORMAL OVERRIDE ON OFF OFF CH SELECT 1 8 7 2 3 CAUTION 6 5 4 USE WITH SPECIFIED EQUIPMENT SEE ITS MANUAL BEFORE CONNECTING
Notes: • The following switches and terminals should be used by qualified service personnel or system installers only. • To change the setting of the following switches, turn off the power of the center module, then turn it back on. q Auxiliary Input On/Off Switch (REMOTE AUX IN, ON/OFF) Set this switch to ON to output the audio (that has been input from the AUX INPUT terminals) to the REMOTE SPEAKER terminals.
w Vehicle Detector Normal/Override On/Off Switches (VEHICLE DETECTOR, NORMAL/OVERRIDE ON/OFF) NORMAL: The vehicle detector turns on only when a vehicle is detected at the menu board. When the detector is turned on, a beep tone is heard in the headset. After the beep tone, the menuboard speaker turns on to allow the communication with the customer. When the vehicle leaves, the vehicle detector turns off. OVERRIDE ON: The vehicle detector is always turned on. OFF: Vehicles are not detected at the menuboard.
!4 Day/Night Selection Switch (DAY/NIGHT) In the Day mode, you will not hear the beep tone of the other lane in the headset that sounds when the vehicle detector is on and that sounds when you press the button T of the order taker unit. In the Night mode, you will hear the beep tone of either lane in the headset when the vehicle detector of either lane is on. Once you press the button T, you will no longer hear your lane’s beep tone.
■ WX-C516 Power Transformer ■ WX-C1027A Headset #3 #4 #6 #5 #3 Mounting Hole This hole is used for mounting the power transformer onto the wall plates. #4 Power Plug To prevent fire or electrical shock, connect this directly to a 3-plug grounded receptacle of 120 V AC, 60Hz. #5 Output terminal (SPARE, AC, AC, GND) 12 V AC, 1 600 mA (UL Listed) is provided at the two terminals (indicated as "AC") to be used for the center module.
■ WX-CT2020 Order Taker Unit $2 $3 $4 $5 $6 A EJECT $7 PWR B $8 VOL $9 WX-CT2020 %0 %1 %2 $2 %3 13
$2 Battery Lock (EJECT) $3 A/B Channel Selection Button (A/B) $4 Page Button (P) $5 Talk Button (T) $6 Power Indicator $7 Channel Indicator $8 Volume Control Buttons (VOL A B) $9 Power Button %0 Earphone Input Jack %1 Microphone Input Jack %2 Switch Pocket %3 Battery (Optional accessory) 14
PREPARATIONS ■ Installations and Connections ■ Preparation Refer to qualified service personnel for details. ■ Battery Charge and Replacement (WX-CH2050A/WX-CT2020) Refer to WX-CT2020/WX-CH2050A Operating Instructions for details. Note: The following procedure applies when using WXCT2020 Order Taker Unit and WX-C1027A Headset. If you use WX-CH2050A All-in-One Headset, refer to the operating instructions of the headset. 1.
■ Maintenance of Headpad Accessories (WX-C1027A: NonScheduled) Notes: • The following procedure applies when using WXC1027A Headset. If you use WX-CT2020 Order Taker Unit, refer to the operating instructions of the headset. • Be sure to use the microphone cover/windproof cushion for WX-C1027A Headset. Otherwise, the headset may be damaged by dust or oil. Replacement of covers and cushion of headset The earspeaker cover and microphone cover are washable. After cleaning, make sure they are dry.
OPERATING PROCEDURES Refer to WX-CT2020/WX-CH2050A Operating Instructions for details. TROUBLESHOOTING Problem Check item The communication between the order taker units and menu board cannot be established. (The TRANSCEIVER MONITOR indicator is not blinking in red.) • Is the POWER switch on the center module turned on? (Refer to p. 10.) • Check the AC power outlet. • Push the CIRCUIT PROTECTOR button. (Refer to p. 10.) • Refer to the dealer or qualified service personnel.
SPECIFICATIONS WX-CC2010 Center Module Operating Frequency: Type of Emission: Type of Antenna: Power Supply: Power Consumption: Menuboard Speaker A and B Output: Remote Speaker A and B Output: Vehicle Detector Input: Dimensions: Weight (Including Antenna): Ambient operating temperature: Transmit; 468.6125 MHz - 469.3875 MHz Receive; 463.6125 MHz - 464.
Panasonic Digital Communications & Security Company Unit of Matsushita Electric Corporation of America Security Systems Group www.panasonic.com/cctv Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094 Zone Office Eastern: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303 Central: 1707 N.Randal Road, Elgin, IL 60123 (847) 468-5205 Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840 2004 © Matsushita Electric Industrial Co., Ltd. All rights reserved. PANASONIC CANADA INC.
