Model No. TH-65PB1U Operating Instructions Electronic Pen Operations Interactive Plasma Display English Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference.
Introduction Abbreviations Windows® refers to the Microsoft® Windows® operating system. Windows® XP refers to the Microsoft® Windows® XP operating system. Windows Vista® refers to the Microsoft® Windows Vista® operating system. Windows® 7 refers to the Microsoft® Windows® 7 operating system. DirectX® refers to the Microsoft® DirectX® application programming interface.
FCC and IC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
System Requirements Computer CPU Operating System Interface IBM® PC/AT compatible with a DVD-ROM drive Intel® Pentium® 4 processor or later Windows(R) XP SP3 or later / Windows Vista(R) SP2 or later / Windows 7 (except for Starter and Home Basic versions) (Windows XP 64-bit edition is not supported.) USB 2.0 Note • For details about the system requirements, refer to “Read Me First” (see page 14) in the install menu of the included DVD-ROM.
Table of Contents Table of Contents Safety Precautions....................................................................................6 Requests regarding handling...................................................................8 Accessories Supplied...............................................................................9 Names and Uses of the Parts.................................................................10 Preparation ...................................................................
Safety Precautions For Your Safety WARNING Operating Safeguards Electronic Pen Do not alter the unit or modify any parts. Alteration or modification can cause fire or electric shock. Do not use near medical equipment. (Do not bring into a surgery room, intensive care unit, critical care unit, etc.) Electromagnetic waves generated by this device can affect equipment, and can cause equipment to malfunction. CHOKING HAZARD Keep the penpoint and battery out of reach of children to prevent swallowing.
Precautions Other Information Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. Usage Note About Using the Battery If a battery is used improperly, the battery may leak, causing corrosion of the unit, or it may burst. To prevent this, always follow the precaution given below.
Requests regarding handling • Do not push down hard on the Pen tip. • If there is surface contamination of the electronic pen, wipe it off with a soft cloth. • • • • • For heavy contamination, wipe it off with a soft cloth dampened with a mild soap solution after squeezing water out of the cloth, and then dry the surface with a soft, dry cloth. Ingress of water droplets may cause a failure. Do not drop the electronic pen because it may get broken or malfunction.
Accessories Supplied Usage Check that all of the following items are included with your Interactive Plasma Display. In the event that an item is missing, please contact your dealer. List of Accessories (Electronic Pen set) Recharger Cable 6.56 ft. (2m) 2 Electronic Pen Adapter 1 Rechargeable AAA Ni-MH Battery* 2 Pen Holder 2 N5EDZ0000006 Electronic Pen N2FZ00000007 2 Pen Tip (Replacement) 2 TKKL5543 Note • Store the extra pen tip along with this operating instructions.
Names and Uses of the Parts 1 Light receiving window 2 Pen tip In the electronic pen mode, you can draw by touching the screen with it. In the mouse mode, touching with it functions as a “left button of mouse”. Touching and holding with it in the mouse mode functions as a “right-click of mouse”. 3 Pen tip cover 4 Menu button Press and hold this button and touch the screen to display the drawing menu. 5 Battery cover 6 Power switch Turns the power of the electronic pen on/off.
; Power indicator Lights green when the power of the electronic pen is “on”. Blinks green when the battery of the electronic pen is low. Lights red during charging and turns off when charging is completed. Blinks red when no rechargeable battery is in during charging or when an incompatible battery is used.
Preparation Inserting (Replacing) Batteries 1. Unlock the battery cover (1), 2. Insert (replace) the battery, and then • When replacing the cover, follow the procedure in • Make sure to use a rechargeable AAA Ni-MH and open the cover (2). reverse. reattach the cover and lock it. battery or a AAA alkaline battery, and ensure that + and - face the correct directions. • Dispose of expired batteries quickly, by covering the terminals in tape and following the disposal regulations in your country/area.
Charging After purchase, charge the electronic pen before use. • Charging is not necessary for an AAA alkaline battery. Connect the recharger port of the electronic pen to the USB port of the computer with the included recharger cable. • The power indicator lights red and charging starts. (It turns off when charging is completed.) COMPUTER Connect to the USB port Recharger cable Guide of charging time and duration time Charging time Duration time Approx. 4 h*1 Approx.
Installing the Software To install the elite Panaboard driver/software/book, follow the procedure below. Notice • Do not connect the electronic pen adapter until the installation is completed. 1. Turn on your computer and start the Windows operating system. • Log into an account with Administrator privileges. 2. Insert the included DVD-ROM into the DVD-ROM drive. • The setup screen will be displayed. • If the setup screen does not appear, select your DVD-ROM drive in Explorer and double-click [Menu.exe].
Operation After finishing preparation of the electronic pen and installation of the software, make settings and connections according to the following procedure. 1. Connect a computer to the Interactive Plasma Display For connection of a computer and the Interactive Plasma Display, see Display Operations of the operating instructions. Before using the electronic pen, make the settings below on the Interactive Plasma Display.
2. Bring the electronic pen to within 2 m from the electronic pen adapter (remove any obstacle between them) • Registration will be completed in a second. When registration is completed, the function indicator lights green for about one second and the power indicator (which was off) lights green. • If a registration error has occurred, the function indicator lights red for about one second. Turn off the electronic pen and perform registration again.
About software Viewing the Help of the Software Download the Latest Software Follow the procedure below to view the help of the software installed on your computer. Follow the procedure below to download the latest version of the software from the download web site. 1. Turn on your computer and start Windows. 2. Open “Software Help” from the Start menu. 1. Turn on your computer and start Windows. 2.
Additional Information Replacing the pen tip of the Electronic Pen As the pen tip of the electronic pen becomes worn, the pen tip will no longer slide easily across the screen. Continuing to use the electronic pen in this condition may make the screen dirty and cause malfunction. Replace the pen tip with a new one as soon as possible. 1. Remove the pen tip cover. 2. Remove the old pen tip and attach the new one.
Troubleshooting When experiencing problems, please refer to the table below for possible solutions. If the problem persists, contact your dealer. Symptom Possible cause and solution See page The power indicator blinks red No rechargeable battery is in during charging or a battery incompatible with this electronic pen is charged → Use a rechargeable AAA Ni-MH battery. 11, 12 The power indicator blinks green The rechargeable AAA Ni-MH battery or alkaline battery is low.
Specifications 20 Type Electronic pen Transmission system 2.4 GHz radio transmission Power source Rechargeable AAA Ni-MH battery x 1 or AAA alkaline battery x 1 External dimensions (L x H) 7.9" (198.5 mm) × 0.9" (22.1 mm) Weight Approx. 0.09 lb. (Approx. 40 g) (including the included rechargeable battery) Operation time Approx. 4 h (Rechargeable AAA Ni-MH battery) Approx. 4 h (AAA alkaline battery) Charging time Approx.
USA Only: Disposal may be regulated in your community due to environmental considerations. For disposal or recycling information, please visit Panasonic website: http://www.panasonic.com/environmental or call 1-888-769-0149. Customer’s Record The model number and serial number of this product can be found on its back cover.