User Manual

CLASSIFICATION
PRODUCT SPECIFICATION
No.
DS-9320-2400-102
REV.
1.1
SUBJECT
WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE
PAGE
39 of 43
CUSTOMER’S CODE
PAN9320 / PAN9310
PANASONIC’S CODE
ENW49A01x3EF & ENW49A02x3EF
DATE
14.03.2016
PANASONIC INDUSTRIAL DEVICES EUROPE GMBH
www.pideu.panasonic.de
28. ORDERING INFORMATION
Model Name
Brand Name
Regulatory
Supported Channel
Description
MOQ
(4)
ENW49A01A3EF
PAN9320
FCC / IC
(1)
for US and
for Canada
Channel 1 ~ 11
2412 ~ 2462 MHz
WLAN IEEE 802.11 b/g/n 2.4GHz Full Embedded
Module with ceramic chip-antenna
500
ENW49A01C3EF
PAN9310
(3)
WLAN IEEE 802.11 b/g/n 2.4GHz Full Embedded
Module with RF bottom pad
500
ENW49A02A3EF
PAN9320
ETSI
(2)
for EU
and other
Channel 1 ~ 13
2412 ~ 2472 MHz
WLAN IEEE 802.11 b/g/n 2.4GHz Full Embedded
Module with ceramic chip-antenna
500
ENW49A02C3EF
PAN9310
(3)
WLAN IEEE 802.11 b/g/n 2.4GHz Full Embedded
Module with RF bottom pad
500
The PAN9320 / PAN9310 will be delivered with a pre-installed firmware, see PAN9320 Communication
Specification
[3]
and PAN9320 Design Guide
[1]
.
Notes:
(1) The model with Regulatory Domain FCC / IC (M/N: ENW49A01A3EF) are only intended to be used in the countries of US
and Canada because only the channels 1 ~ 11 (2412 ~ 2462 MHz) are supported in the 2.4GHz ISM band. It is not
possible to change the pre-stored Region Code in order to change the Regulatory Domain. Thus the module labeling
contains the FCC Grant ID.
(2) The model with Regulatory Domain ETSI (M/N: ENW49A02A3EF) are mainly intended to be used in European countries
because the channels 1 ~ 13 (2412 ~ 2472 MHz) are supported. The Region Code is pre-configured (using Default Config
Content in Flash memory) to Regulatory Domain ETSI and thus the module labeling doesn’t contain the FCC ID. At the
end the customer is able to change applied Region Code by his own Customer Config Content to be stored during
customer OEMs product production in the flash memory. It means the FCC Regulatory Domain can be configured as well,
but the customer has to certify the end product by itself.
(3) The models with brand name PAN9310 don’t have the Chip antenna on module. The Grant ID’s marked on module
labelling are referenced and are only valid in case of customer is applying the same antenna (listed in 31.1.5) including
the reference design described in the Design Guide
[1]
. In this case the customer can refer to the pre-qualified module’s
modular approval which needs finally to be approved by the certification body of regulatory authority.
(4) Abbreviation for Minimum Order Quantity (MOQ). The standard MOQ for mass production is 500 pieces, fewer only on
customer demand. Samples for evaluation can be delivered at any quantity via the distribution channels.
29. SOFTWARE VERSIONS
The version numbers of the embedded MCU firmware and WLAN SoC firmware can be read out by UART
commands which are specified in the PAN9320 Communication Specification
[3]
and listed below:
No.
Item
UART Command
Response example
1
MCU firmware version
get system firmware
get system firmware 0 1.9.0.1
2
WLAN SoC firmware version
get system wifi_ver
get system wifi_ver 0 "w8782-B0, RF878X, FP69, 14.69.12.p40"
30. ROHS DECLARATION
Declaration of environmental compatibility for supplied products:
Hereby we declare to our best present knowledge based on declaration of our suppliers that this product
does not contain the following substances which are banned by Directive 2002/95/EC (RoHS) or contains a
maximum concentration of 0.1% by weight in homogeneous materials for
 Lead and lead compounds
 Mercury and mercury compounds
 Chromium (VI)
 PBB (polybrominated biphenyl) category
 PBDE (polybrominated biphenyl ether) category
And a maximum concentration of 0.01% by weight in homogeneous materials for
 Cadmium and cadmium compounds