User Manual
CLASSIFICATION
PRODUCT SPECIFICATION
No.
DS-9320-2400-102
REV.
1.1
SUBJECT
WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE
PAGE
40 of 43
CUSTOMER’S CODE
PAN9320 / PAN9310
PANASONIC’S CODE
ENW49A01x3EF & ENW49A02x3EF
DATE
14.03.2016
PANASONIC INDUSTRIAL DEVICES EUROPE GMBH
www.pideu.panasonic.de
31. REGULATORY INFORMATION
31.1. FCC FOR US
31.1.1. FCC Notice
The PAN9320, including the ceramic antenna (ENW49A01A3EF) and the PAN9310 SMD type
(ENW49A01C3EF), including with the antennas, which are listed in 31.1.5, complies with Part 15 of
the FCC Rules.
The device meets the requirements for modular transmitter approval as detailed in FCC public
Notice DA00-1407.transmitter Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
The FCC identifier for ENW49A01x3EF
(
16
)
is FCC ID: T7V-9320
31.1.2. Caution
The FCC requires the user to be notified that any changes or modifications made to this device that
are not expressly approved by Panasonic Industrial Devices Europe GmbH may void the user's
authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help
31.1.3. Label Requirements
The Original Equipment Manufacturer (OEM) must ensure that FCC labelling requirements are
met. This includes a clearly visible label (laser marking) on the outside of the OEM enclosure
specifying the appropriate Panasonic FCC identifier for this product as well as the FCC Notice
above. The FCC identifier is FCC ID: T7V-9320 for model ENW49A01x3EF
(16)
.
This FCC identifier is valid for PAN9320, for details see the Chapter 28 Ordering Information. In
any case the end product must be labelled exterior with
"Contains FCC ID: T7V-9320"
31.1.4. Antenna Warning
The related model number for the device is ENW49A01C3EF (PAN9310 with SMD pad). For
details, see the Chapter 28 Ordering Information. The device is tested with a standard SMA
connector and with the antenna listed below. When integrated in the OEMs product, these fixed
antennas require installation preventing end-users from replacing them with non-approved
antennas. Any antenna not in the following table must be tested to comply with FCC Section
15.203 for unique antenna connectors and Section 15.247 for emissions. The FCC identifier for the
device with the antenna listed in chapter 31.1.5 is the same (FCC ID: T7V-9320).
16
x = „A“ for PAN9320 and x = „C“ for PAN9310 (e.g. ENW49A01A3EF x = “A”)