User's Manual
Table Of Contents
- KEY FEATURES
- APPLICATIONS FOR THE MODULE
- DESCRIPTION OF THE MODULE
- SCOPE OF THIS DOCUMENT
- HISTORY FOR THIS DOCUMENT
- TERMINAL LAYOUT
- BLOCK DIAGRAM
- KEY PARTS LIST
- TEST CONDITIONS
- ABSOLUTE MAXIMUM RATINGS
- OPERATING CONDITIONS
- DC ELECTRICAL CHARACTERISTICS
- A/D CONVERTER CHARACTERISTICS
- AC ELECTRICAL CHARACTERISTICS
- MECHANICAL REQUIREMENTS
- SOLDERING TEMPERATURE-TIME PROFILE (FOR REFLOW SOLDERING)
- MODULE DIMENSIONS
- FOOT PRINT OF THE MODULE
- LABELING DRAWING
- RECOMMENDED LAND PATTERN
- SOFTWARE
- RELIABILITY TESTS
- APPLICATION NOTES
- PACKAGING
- ORDERING INFORMATION
- ROHS DECLARATION
- DATA SHEET STATUS
- REGULATORY INFORMATION
- RELATED DOCUMENTS
- GENERAL INFORMATION
- LIFE SUPPORT POLICY
CLASSIFICATION
Einstufung
PRODUCT SPECIFICATION
Produktspezifikation
No.
DS-ETR2-2400-102
REV.
D
SUBJECT
Thema
MODEM FOR IEEE802.15.4 (ZIGBEE)
“ZigBee” Modem“ (IEEE802.15.4)
PAGE
Seite
13 of 29
CUSTOMER’S CODE
ETRX2
PANASONIC’S CODE
ENWC9A0xyzE
DATE
Datum
01.08.2006
HIGH FREQUENCY PRODUCTS DIVISION
Module Business
PANASONIC ELECTRONIC DEVICES
(EUROPE) GmbH
APPROVED
genehmigt
CHECKED
geprüft
DESIGNED
erstellt
Notes:
(1) For more information about the internal regulated core voltage refer to part 5.7 in [2]. As the
internal regulated core voltage at REG_OUT mainly feeds circuitry on ETRX2, the REG_OUT
module pin may only be slightly loaded and without feeding noise to REG_OUT.
In case the dc regulator option is mounted REG_OUT is connected to the regulator option output
instead and the internal regulated core voltage is not accessible.
13. A/D CONVERTER CHARACTERISTICS
No Item
1 ATD characteristics refer to datasheet EM250 part 5.5 ADC Module
2
ATD timing/performance
characteristics
refer to datasheet EM250 part 5.5 ADC Module
14. AC ELECTRICAL CHARACTERISTICS
VBAT
= 3.0V, T
amb
= 25°C, measured at 50Ω terminal load
(1)
No Limit
Unit
Receiver
Min Typ Max
1 Sensitivity for 1% Packet Error Rate (PER) -85 -96 - dBm
2
Sensitivity for 1% Packet Error Rate (PER)
(boost mode)
-85 -97 - dBm
3
Saturation (maximum input level for correct operation,
low gain)
0 - - dBm
4
Adjacent Channel Rejection
(1% PER and desired signal –82dBm acc. to [1])
35 dB
5
Alternate Channel Rejection
(1% PER and desired signal –82dBm acc. to [1])
40 dB
6
Channel Rejection for all other channels
(1% PER and desired signal –82dBm acc. to [1])
40 dB
7
802.11g rejection centered at +12MHz or –13MHz
(1% PER and desired signal –82dBm acc. to [1])
40 dB
8
Co-channel rejection
(1% PER and desired signal –82dBm acc. to [1])
-6 dBc
9
Relative frequency error
(2x40ppm required by [1])
-120 120 ppm
10
Relative timing error
(2x40ppm required by [1])
-120 120 ppm
11 Linear RSSI range 40 dB
12 Spurious Emissions <1GHz - TBD -57 dBm
13 Spurious Emissions >1GHz - TBD -47 dBm
Notes:
(1) At pin 38 RF or U.FL socket, for all channels number 11,12,..., 26 according to [1]