User Manual
Table Of Contents
- 1 SCOPE OF THIS DOCUMENT
- 2 KEY FEATURES
- 3 BLUETOOTH LOW ENERGY
- 4 APPLICATIONS FOR THE MODULE
- 5 DESCRIPTION FOR THE MODULE
- 6 DETAILED DESCRIPTION
- 7 BLUETOOTH FEATURES
- 8 BLOCK DIAGRAM
- 9 TEST CONDITIONS
- 10 GENERAL DEVICE REQUIREMENTS AND OPERATION
- 11 BLUETOOTH RF PERFORMANCE
- 12 SOLDERING TEMPERATURE-TIME PROFILE (FOR REFLOW SOLDERING)
- 13 MODULE DIMENSION
- 14 PAN1026 FOOTPRINT OF THE MODULE
- 15 CASE MARKING
- 16 MECHANICAL REQUIREMENTS
- 17 RELIABILITY TESTS
- 18 CAUTIONS
- 19 PACKAGING
- 20 ORDERING INFORMATION
- 21 INFORMATION REGARDING SOFTWARE VERSIONS
- 22 SOFTWARE
- 23 SOFTWARE BLOCK DIAGRAM
- 24 ROHS AND REACH DECLARATION
- 25 DATA SHEET STATUS
- 26 HISTORY FOR THIS DOCUMENT
- 27 RELATED DOCUMENTS
- 28 GENERAL INFORMATION
- 29 REGULATORY INFORMATION
- 30 INDUSTRY CANADA CERTIFICATION
- 31 EUROPEAN R&TTE DECLARATION OF CONFORMITY
- 32 LIFE SUPPORT POLICY
CLASSIFICATION PRODUCT SPECIFICATION
No.
DS-1026-2400-102
REV.
0.3
SUBJECT
CLASS 2 BLUETOOTH LOW ENERGY
SPP MODULE
PAGE 34 of 35
CUSTOMER’S CODE
PAN1026
PANASONIC’S CODE
ENW89837AxKF
DATE 02.10.2013
PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de
30 INDUSTRY CANADA CERTIFICATION
PAN1026 is licensed to meet the regulatory requirements of Industry Canada (IC),
license: IC: 216Q-PAN10
Manufacturers of mobile, fixed or portable devices incorporating this module are advised to
clarify any regulatory questions and ensure compliance for SAR and/or RF exposure limits.
Users can obtain Canadian information on RF exposure and compliance from www.ic.gc.ca
.
This device has been designed to operate with the antennas listed in Table 20 above,
having a maximum gain of 0.9 dBi. Antennas not included in this list or having a gain
greater than 0.9 dBi are strictly prohibited for use with this device. The required antenna
impedance is 50 ohms. The antenna used for this transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
Due to the model size the IC identifier is displayed in the installation instruction only and
can not be displayed on the modules label due to the limited size (8.7x15.6mm).
30.1 IC NOTICE
The devices PAN1026, for details r
efer to Chapter 20, including the antennas, which are
listed in 29.5, complies with Canada RSS-GEN Rules. The device meets the requirements
for mod
ular transmitter approval as detailed in RSS-GEN.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received, including
interference that may cause undesired operation.
30.2 LABELING REQUIREMENTS
The Original Equipment Manufacturer (OEM)
must ensure that IC labelling requirements
are met. This includes a clearly visible label on the outside of the OEM enclosure specifying
the appropriate Panasonic IC identifier for this product as well as the IC Notice above. The
IC identifier is 216Q-PAN10. This IC identifier is valid for all PAN1026 modules, for details,
see the Chapter 20 - Ordering Information.
In any case
the end product must be labelled exterior with
"Contains IC: 216Q-PAN10"
31 EUROPEAN R&TTE DECLARATION OF CONFORMITY
Hereby,
Panasonic Industrial Devices Europe GmbH, declares that the Bluetooth module
PAN1026 and their versions is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC. As a result of the conformity assessment
procedure described in Annex III of the Directive 1999/5/EC, the end-customer equipment
should be labelled as follows:
All versions of the PAN1026 in the specified reference design can be used in the following
countries: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, The Netherlands, the United Kingdom,
Switzerland, and Norway.