Operating Instructions Base Unit for SIP Cordless Phone Model No. KX-TGP700 SIP Cordless Handset Model No. KX-TGP700 KX-TPA70/KX-TPA73 KX-TPA70/KX-TPA73 Thank you for purchasing this Panasonic product. Please read this manual carefully before using this product and save this manual for future use. Please use the batteries provided and charge the batteries for about 6 hours before using the handset for the first time. Note • In this manual, the suffix of each model number is omitted unless necessary.
Introduction Introduction Outline This manual describes information about the installation and operation of KX-TGP700, KX-TPA70 and KX-TPA73. Related Documentation • Quick Start Guide Describes basic information about the installation and safety precautions to prevent personal injury and/or damage to property. • Administrator Guide Describes detailed information about the configuration and management of this unit. This guide describes information about the KX-TGP700 only.
Introduction Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License. MODEL NO. SERIAL NO. DATE OF PURCHASE NAME OF DEALER DEALER’S ADDRESS DEALER’S TEL. NO.
Introduction 4
Table of Contents Table of Contents 1 Important Information .......................................................... 7 1.1 1.1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2 Before Operating the Telephones ..................................... 19 2.1 2.1.1 2.2 2.2.1 2.3 2.3.1 2.3.2 2.4 2.4.1 3 Making Calls ................................................................................................ 34 Receiving Calls ................................................................... 35 4.
Table of Contents 6
Section 1 Important Information 7
1.1 Important Information 1.1 Important Information 1.1.1 Data Security • This telephone communicates using digital signals that are difficult to intercept. However, it is possible that the signals could be intercepted by a third party. • To avoid unauthorized access to this product: –Keep the password (e.g., PIN for registration) secret. –Change the default password. –Set a password that is random and cannot be easily guessed. –Change the password regularly.
1.2 For Users in European Countries 1.2 For Users in European Countries The following declaration is applicable to KX-TGP700CE/KX-TGP700UK/ KX-TPA70CE/KX-TPA70UK/KX-TPA73CE/KX-TPA73UK only The DECT is abbreviation of the Digital Enhanced Cordless Telecommunications. This device is a DECT operating in the frequency band of 1880 MHz to 1900 MHz. The usage of this device is generally allowed in all EU countries.
1.4 For Users in Australia and the United Kingdom 1.4 For Users in Australia and the United Kingdom • This unit is capable of being used in conjunction with hearing aids fitted with inductive coil pick-ups. The handset should be held as for normal conversation. For operation, the hearing aid should be set to its "T" position or as directed in the operating instructions for the hearing aid. • This unit is designed to aid the visually handicapped to locate dial keys and buttons. 1.
1.6 For Users in the United States 1.6 For Users in the United States FCC Note • This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
1.6 For Users in the United States FCC ID can be found inside the battery compartment (KX-TPA70/KX-TPA73) or on the bottom of the units (KX-TGP700). Privacy of communications may not be ensured when using this phone. Hearing Aid Compatibility This telephone provides magnetic coupling for hearing aids as defined by the FCC in 47 CFR Section 68.316. Use only handsets or other acoustic devices with this equipment that are compliant with the hearing aid compatibility requirements of FCC Part 68.
1.7 For Users in Canada 1.7 For Users in Canada Innovation, Science and Economic Development Canada Notices and Other Information This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. Note • This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s).
1.8 For Best Performance RF Exposure Warning: • This product complies with ISED radiation exposure limits set forth for an uncontrolled environment. • To comply with ISED RF exposure requirements, KX-TGP700 must be installed and operated 20 cm (8 inches) or more between the product and persons’ bodies. • This product may not be collocated or operated in conjunction with any other antenna or transmitter. • The handset may be carried and operated with only the specific provided belt-clip.
1.8 For Best Performance Environment • Keep the product away from heating appliances and devices that generate electrical noise, such as fluorescent lamps and motors. These noise sources can interfere with performance of the product. • Do not use the product in rooms where the temperature is less than 0 ℃ (32 ℉) or greater than 40 ℃ (104 ℉). • To avoid damage, charge the battery only in temperatures ranging from 5 ℃ (41 ℉) to 40 ℃ (104 ℉).
1.9 Battery Information (KX-TPA70/KX-TPA73) 1.
1.9 Battery Information (KX-TPA70/KX-TPA73) When the low battery warning is displayed, charge the batteries for about 6 hours. The battery strength icon will then display the correct reading. Note • There is a danger of explosion if the batteries are incorrectly replaced. (For the United States and Canada only) Nickel metal hydride batteries that are recyclable power the product you have purchased. Please call 1-800-8-BATTERY for information on how to recycle these batteries.
1.9 Battery Information (KX-TPA70/KX-TPA73) • There is a danger of explosion if the batteries are incorrectly replaced. (For the United States and Canada only) A lithium ion/polymer battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY for information on how to recycle this battery. CAUTION RISK OF EXPLOSION IF BATTERIES ARE REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Section 2 Before Operating the Telephones 19
2.1 Before Operating the Telephones 2.1 Before Operating the Telephones 2.1.1 System Overview • Expandable to cordless handsets/desk phones [KX-TPA60, KX-TPA65, KX-TPA68, KX-TPA70, KX-TPA73, KX-UDT series (except for KX-UDT111)]. Up to 16 phones in total.
2.1.
2.2 Accessory Information 2.2 Accessory Information 2.2.1 Included Accessories KX-TGP700/KX-TGP700CE/KX-TGP700UK/KX-TGP700AL AC adaptor for Base unit: 1 Model No. Part No. KX-TGP700 PNLV236 KX-TGP700CE PNLV236CE KX-TGP700UK PNLV236E KX-TGP700AL PNLV236AL DC Output: 5.5 V/1.0 A Ethernet Cable: 1 Screws: 2 Washers: 2 KX-TPA70 AC adaptor for Charger: 1 Model No. Part No.
2.2.1 Included Accessories Screws: 2 Washers: 2 *1 Rechargeable AAA Ni-MH 1.2 V, 630 mAh batteries KX-TPA73 AC adaptor for Charger: 1 Model No. Part No. KX-TPA73/KX-TPA73C PQLV219 KX-TPA73CE PQLV219CE KX-TPA73UK PQLV219E KX-TPA73AL PQLV219AL Battery*1: 1 Belt Clip: 1 DC Output: 6.5 V/0.5 A Charger: 1 Screws: 2 Washers: 2 *1 Rechargeable Li-ion 3.
2.3 Location of Controls 2.3 Location of Controls 2.3.1 Base Unit (KX-TGP700) Status Indicator Status Color Green Red 24 Light pattern Meaning On • The base unit is connected to the Internet. The startup process is complete and you may now make and receive internet calls. Slow Flashing • The base unit is being used for a call. Quick Flashing • The handset/desk phone is busy. On • When the base unit is turned on, the STATUS indicator lights in red for about 40 seconds.
2.3.1 Base Unit (KX-TGP700) Status Color Amber Light pattern Meaning On • The base unit’s IP address may conflict with the IP addresses of other devices on your local network. Contact your administrator for further information. Slow Flashing • The base unit is obtaining an IP address or is obtaining configurations. Please wait. • The base unit is registering with your phone system. Please wait • If the STATUS indicator continues flashing, check the following: –Network settings may not be correct.
2.3.1 Base Unit (KX-TGP700) Status Off Meaning Light pattern Color — • The base unit power is off. • The Ethernet cable is not connected properly. Connect it. • Your network devices (hub, router, etc.) are turned off. Check the LEDs for the link status of the devices. Note • The indicator flashing patterns are as follows: –Slow Flashing: 60 times per minute –Quick Flashing: 240 times per minute Handset locator button You can locate a misplaced handset/desk phone by paging it.
2.3.2 Handset (KX-TPA70/KX-TPA73) 2.3.2 Handset (KX-TPA70/KX-TPA73) [Back View] (KX-TPA70 only) Suffix: (none) Suffix: C/UK/AL/CE (KX-TPA73 only) Ringer/Charge/Message Indicator Status Color Red Meaning Light pattern On Charging Slow Flashing There is a new missed call or voice mail. Quick Flashing Charging failure Green On Fully charged Green/Red Quick Flashing Receiving a call *LED color can be changed by setting.
2.3.2 Handset (KX-TPA70/KX-TPA73) Status Color Off Meaning Light pattern — The handset is not connected to the charger. Headset Jack For KX-TPA70: For KX-TPA73: The headsets can be used with this unit. (Not all operations with the headsets can be guaranteed.) For up-to-date information about headsets that have been tested with this unit, refer to the following web sites: https://panasonic.
2.3.2 Handset (KX-TPA70/KX-TPA73) DOWN ( ) Short press Used to access the call log on the screen. Long press Used to display the line status. In this manual, when a procedure instructs you to "press the [CENTER] key to confirm the selection. *1 ", you can also press When the BroadCloud (Presence) feature is enabled, the phone will operate as follows. Contact your administrator for further information. LEFT: Used to display Presence. RIGHT: Used to display Favorites.
2.4 The Display and Icons 2.4 The Display and Icons 2.4.1 Display [Example: In standby mode] Pictograph *1 Signal Strength Indicator Strong Battery Indicator - Full Signal Strength Indicator Medium Battery Indicator - Medium Signal Strength Indicator Weak Battery Indicator - Low Signal Strength Indicator Very weak Battery Indicator - Very low Signal Strength Indicator - Out of range Battery Indicator - Needs to be charged.
2.4.1 Display Handset/Desk phone number and Name (when connecting to a KX-TGP700 only) Talk time (when the line is on a call) and incoming call display (when a call is received or recalled) Full-Charge Display When a handset is placed in the charger while it is powered on, "Fully Charged" will be displayed when it is fully charged. If a handset that is fully charged is placed in the charger while it is powered on, "Fully Charged" is displayed.
2.4.
Section 3 Making Calls 33
3.1 Making Calls 3.1 Making Calls • You can confirm that the number was dialed correctly before calling (Predialing) by entering the number, then .
Section 4 Receiving Calls 35
4.1 Answering Calls 4.1 Answering Calls To answer an incoming call Note • When receiving an intercom call, the Handset Name is displayed on the LCD.
Section 5 Installation and Setup 37
5.1 Installation and Setup 5.1 Installation and Setup Note • Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation. WARNING • To reduce the risk of fire or electric shock, do not overload AC outlets and extension cords. • Completely insert the AC adaptor/power plug into the AC outlet. Failure to do so may cause electric shock and/or excessive heat resulting in a fire.
5.2.1 Battery Installation PQLV219xx • The AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected. • Fasten the AC adaptor cord to the cord holder. • Use only the included Panasonic AC adaptor. 5.2.1 Battery Installation Open the battery cover, insert the batteries, and close the cover as indicated below. For KX-TPA70 For KX-TPA73 5.2.
5.2.3 Charging the Batteries • The charge indicator on the handset will turn on green when the batteries are fully charged. • When a handset is placed in the charger while it is powered on, "Fully Charged" will be displayed when it is fully charged. If a handset that is fully charged is placed in the charger while it is powered on, "Fully Charged" is displayed.
5.2.4 Wall Mounting 5.2.4 Wall Mounting Note • Make sure that the wall and the fixing method are strong enough to support the weight of the unit. KX-TGP700 (Base unit) 1. Drive the screws into the wall either 85 mm (3 7/20 in) apart, and mount the unit on the wall. *1 *2 *3 *1 85 mm (3 7/20 in) *2 Washer *3 Drive the screw to this point.
5.2.
Section 6 Appendix 43
6.1 Appendix 6.1 Appendix 6.1.1 Specifications KX-TGP700 (Suffix: all) Item Specifications Power Supply AC adaptor/PoE (IEEE 802.3af) Class 2 Maximum Power Consumption 5.0 W/4.8 W (AC adaptor/PoE) Operating Environment 0 ℃ (32 ℉) to 40 ℃ (104 ℉) Ethernet Port (LAN) 1 (RJ45) Ethernet Interface 10Base-T/100Base-TX (Auto/100MB-FULL/100MB-HALF/10MB-FULL/10MBHALF) CAT-iq 2.0 Wideband Codec G.722/Opus Narrowband Codec G.711a-law/G.711μ-law/G.
6.1.2 RF Specifications Item KX-TPA70 KX-TPA73 CAT-iq 2.0 2.0 Key Backlight Yes (White) Yes (White) Strap Hole No No Belt Clip Yes (Fixed type) Yes (Swibel type) Display 2.2-inch TFT Backlight LCD, 65,000 colors 2.2-inch TFT Backlight LCD, 65,000 colors Headset Jack 1 (ø 3.5 mm [7/50 in]) 1 (ø 3.5 mm [7/50 in]) Batteries Ni-MH AAA × 2 (1.2 V, 630 mAh) Li-ion (3.
6.1.2 RF Specifications Item USA, Canada Latin America Other countries/ areas Frequency Band 1920 MHz to 1930 MHz 1910 MHz to 1920 MHz 1880 MHz to 1900 MHz Number of Carriers 5 5 10 Transmission Output Peak 0.11 W Peak 0.25 W Peak 0.25 W KX-TPA73 Item 46 All the areas Wireless Interface Bluetooth Frequency Band 2.402 GHz to 2.
Panasonic Corporation 1006, Oaza Kadoma, Kadoma-shi, Osaka 571-8501, Japan https://panasonic.net/cns/pcc/support/sipphone/ Panasonic Corporation of North America Two Riverfront Plaza, Newark, New Jersey 07102-5490 https://panasonic.net/cns/pcc/support/sipphone/ Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 http://www.panasonic.