Initial Setup Professional/ Industrial Video TV/ DVD / VCR Combination Operating Instructions AG-527DVDE Basic Operation TV Operation Timer Operation Model No. Advanced Operation • Initial Setup and Connection Procedures are on pages 11 to 17. Please read these instructions carefully before attempting to connect, operate, or adjust this product. Please save this manual. AG527DVDE (P01).
Important Safeguards and Precautions READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON UNIT INSTALLATION 1 POWER SOURCE CAUTION Operate only from power source indicated on unit or in this manual. If uncertain, have your Electric Utility Service Company or Video Products Dealer verify your home power source. 2 POWER CORD PLUG For safety, this unit has a polarized type plug (one wide blade), or a three-wire grounding type plug.
Safety Precautions/Mesures de sécurité Warning : To prevent fire or shock hazard, do not expose this equipment to rain or moisture. Caution : To prevent electric shock, match wide blade of plug to wide slot, fully insert. Avertissement : Afin de prévenir tout risque d’incendie ou de chocs électriques, ne pas exposer cet appareil à la pluie ou à une humidité excessive.
Before Using Congratulations Loading the Batteries on your purchase of one of the most sophisticated and reliable products on the market today. Used properly, it will bring you and your family years of enjoyment. Please fill in the information below. The serial number is on the tag located on the back of your unit. 1) Open the cover. 2) Insert batteries as marked. Date of Purchase Dealer Purchased From Dealer Address Dealer Phone No. AG-527DVDE Model No. Serial No. 3) Close the cover.
Table of Contents Initial Setup Important Safeguards and Precautions / Safety Precautions ........ 2 - 3 Before Using ........................................................................................ 4 Information (Unit, Cassette, Disc) .................................................. 6 - 7 Location of Controls ..................................................................... 8 - 11 Connections ................................................................................
Information (Unit, Cassette, Disc) Head Cleaning Specifications Playing older or damaged tapes may eventually cause video heads to become clogged. Head Clog Sensor Display Picture Tube: During playback this screen appears if clogging is detected. To remove screen, press PLAY on the remote or unit.
The unit can play back discs bearing any of the following marks: DVD 3” (8 cm) disc / 5” (12 cm) disc Video CD 3” (8 cm) disc / 5” (12 cm) disc CD 3” (8 cm) disc / 5” (12 cm) disc MP3 Discs which cannot be played with this unit • DVD with Region No. other than “1” or “ALL” • DVD of PAL system • CD-ROM • DVD-RAM • CDV • DVD-ROM • CD-G • Do not try to play a Photo CD. is a registered trademark.
Location of Controls Remote Control Buttons EJECT/OPEN/CLOSE DVD See next page. Sets to DVD mode. POWER LIGHT Turns the unit on or off. See next page. TV/VCR DSS/CABLE Sets to TV/VCR mode. Sets the remote to control some basic DDS or Cable box functions. MUTE FM Mutes the sound instantly. Receives FM radio signal. CHANNEL UP/DOWN VOLUME UP/DOWN Selects a channel. Adjusts volume. SURROUND Creates a deeper, 3-D sound effect.
Initial Setup Universal Light Tower® Illuminated Remote Control LIGHT button: , DSS/CABLE, CH UP/DOWN, VOL UP/DOWN) When LIGHT is pressed, (DVD, buttons will light for 5 seconds for easy button location. If no button is pressed in 5 seconds, the light goes out to conserve the batteries. EJECT/OPEN/CLOSE button: When this button is pressed in TV-VCR mode, the tape is ejected. This button is inoperative if pressed during recording. If pressed in DVD mode, the disc tray opens or closes.
Location of Controls (continued) Front View of the unit If the disc cannot be removed... First, unplug unit. Then, prepare a rigid wire (e.g. an extended paper clip) and, applying moderate force, insert it straight into the hole at the base of the tray. The tray will eject a little. Now, pull the tray all the way out and remove the disc. Disc Tray Cassette Compartment DVD PHONES Connect an earphone or headphones. Built-In SpeakerX2 CHANNEL UP/DOWN (See page 8.) TRACKING UP/DOWN (See page 8.
Audio Output Connector (L/R) Pg. 12 VHF/UHF Antenna Input Terminal See below. Optical digital audio output connector Pg. 13 VHF/UHF AC Power Plug When plugged into an AC outlet, this unit consumes 3.5 W of electric power in OFF condition. DIGITAL AUDIO OUT (PCM/BITSTREAM) OPTICAL AUDIO OUT R L Connections For ANT./Cable Connect the cable from Antenna/Cable to the VHF/UHF terminal on the unit. IN from ANT.
Connections (continued) Audio connections Ready Checklist ■ Unit ➛ Amplifier ➛ Speaker Unit Turn down the volume, then turn this unit, as well as other equipment to be connected, off before proceeding with connection. Do not block ventilation holes of any equipment and arrange them so that air can circulate freely. Read through the instructions before connecting other equipment. Ensure that you observe the color coding when connecting audio and video cables.
or Unit ➛ dts (digital theater systems) Decoder ➛ Amplifier ➛ Speaker When DVDs recorded in Dolby Digital or dts are played, Dolby Digital bitstream or dts bitstream is output from the unit Optical digital audio output connector. When the unit is connected to a Dolby Digital decoder or dts decoder, you can enjoy theater-quality audio in your home. [An optical digital audio cable (optional) is required when an optional Dolby Digital decoder or dts decoder is used.
Initial Setup (Ready to Play) Please make all cable or antenna connections before powering on. Initial Setup (Ready to Play) Press 1 2 on the remote for TV-VCR mode. Plug the unit power cord into an AC wall outlet. Press POWER* on the remote or unit. The unit comes on and auto channel and clock set starts. CH AUTO SET PROCEEDING POWER TV-VCR • If you use a cable box, turn it on and set it to the Public Broadcasting Service (PBS) channel in your time zone.
*Important: If a remote control button does not work when pressed, press the and try the button again. Reset all unit Memory Functions If AUTO CLOCK SET was incomplete, manually set the clock as follows. 1 Press ACTION on the Remote to display SET CLOCK Menu screen. When moving unit to a new location, or if a mistake was made in the Initial Setup section. • Make sure a tape is not inserted in the unit.
Reset Language, Channels, Clock, 1 LOCK LANGUAGE CH CLOCK SELECT : END : ACT I ON to display MAIN MENU. 1 53 TV 2 Press ACTION* M A I N MENU DVD Time Z SET : SET Clock Channels Language 1) Press select “CH.” 1) Press to select language icon. to 1) Press to select “CLOCK.” M A I N MENU M A I N MENU M A I N MENU DVD DVD 53 TV SELECT : END : ACT I ON TV 1 SET : SET 2) Press SET.
*Important: If a remote control button does not work when pressed, press the button on the remote and try the button again. Time Zone Adjust Initial Setup Time Zone Adjust 4)Press and press SET to select and set the month, date, year, time, and DST (Daylight Saving Time). (Only when Auto Clock is set.) NUMBER keys 1) Press to select “CLOCK.” ADD/DLT M A I N MENU DVD 53 To Make Corrections, repeatedly press to move to error, then correct.
Playback a Tape Ready Checklist All connections are made. Your unit is plugged in. 1 Insert a tape. • The unit power comes on automatically. Record tab To prevent tape jam, remove loose or peeling labels from tapes. Record On a Tape 1 2 3 Insert a tape with record tab. • The unit power comes on automatically. Press CH or number keys to Select Channel. • For “LINE” input, see bottom of next page. Press SPEED to select recording speed (see page 4).
Copy Your Tapes (Dubbing) *Important: If a remote control button does not work when pressed, press the button on the remote and try the button again. Connections you’ll need to make Recording (Editing) unit Playing (Source) VCR IN R-AUDIO-L VIDEO MONO Playback (Source) 1 IN FROM ANT. OUT TO TV VIDEO IN L-AUDIO IN-R Basic Operation OUT Recording (Editing) unit Insert blank tape with record tab. Insert prerecorded tape. • Dubbing tapes protected with Copy Guard will have poor quality results.
Basic DVD Operation Ready Checklist All connections are made. (See pages 11-13.) Your unit is plugged in. If unit is connected to an audio amplifier, turn the stereo system’s power on. 1 2 Press POWER* on the remote or unit. Insert a disc. • If a disc is already inserted, go to step 3. (Depending on the disc, playback may start automatically.) 1) Press OPEN/CLOSE. 2) Place disc into disc tray. • Hold disc by its edges only (page 7) with printed side up and use guides to place into 1 tray.
*Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. ■ Forward/Reverse rapid scene search ➛ Press FF/SLOW+ or REW/SLOWduring play. ➛ Press PLAY to release. ■ Forward/Reverse Chapter/Track Skip | or | during play. ➛ Press SKIP Each press skips a chapter (DVD) or track (Video CD/CD). Pressing | SKIP once midway through a chapter/track returns to start of that chapter/track. Each additional press skips back one chapter/ track.
TV Operation 1 *Important: If a remote control button does not work button on when pressed, press the the remote and try the button again. Press POWER* on the remote or unit. 2 08 ABC Ready Checklist All connections are made. (See page 11). Your unit is plugged in. Use CH or number keys to select a channel. VOL + / VOL POWER 3 Press VOL + or VOL to adjust volume.
MTS Broadcast / TV Stereo System Receivable Broadcast Types ® Equipped with -TV Noise Reduction for true MTS ® reproduction. -TV Noise Reduction is required for good stereo separation and audio fidelity. ® is a registered trademark, and ® is licensed by Technology Licensing. The following are possible audio broadcast types and on-screen displays. The signal being received is indicated with an “ ” mark while the selected audio mode is indicated with an arrow.
Closed Caption System Closed Caption is ... This multi-use system not only allows the hearing impaired to enjoy selected programs, but also makes useful information from TV stations available to everyone. Closed Caption Mode Feature 1 2 Press ACTION* to display MAIN MENU.
*Important: If a remote control button does not work when pressed, press the and try the button again. button on the remote Caption On Mute Feature Closed Caption narration, if available, is displayed when MUTE button is pressed for silence. 1 2 Press ACTION to display MAIN MENU.
TV Timer Features Ready Checklist ON-TIMER with Alarm This unit can be set to automatically power on in one of 4 modes (TV, VCR Playback, FM radio, or DVD/Video CD/CD.) You can also combine the On-Timer with a one minute alarm that gradually increases in volume. 1 2 Press PROG* to display SET PROGRAM screen. SET PROGRAM T I MER PROGRAMM I NG ON T I MER SLEEP T I MER : 00 SELECT : SET : SET END : PROG 3 1)Press to select “ON TIMER.” 2)Press SET to display ON TIMER screen.
On-Screen Display (OSD) *Important: If a remote control button does not work when pressed, press the button on the remote and try the button again. TV/VCR Status & Clock Display Press DISPLAY to display or remove the overlay. Channel Caption (See page 38.) Function Status Current Time Rec Time Remaining (OTR mode only, see page 18.) ABC REC 1 2 : 0 0PM -0 : 1 2 : 3 4 0 : 25 SP STEREO SAP MONO Counter Tape Speed (See page 4.) Receivable Broadcast Types (See page 23.
FM Radio FM Radio is ... This unit has an FM radio with built-in antenna, 9 station preset, and a band range of 87.5 ~ 108.1 MHz. You can even set the On-Timer (page 26) to wake up to your favorite radio station. FM Radio Setup 1 2 3 Press FM on the remote to display FM radio mode. Press a number key* (1~9) to select the FM preset number. 1 2 : 0 0PM FM 1 87. 5MHz 1 2 : 0 0PM FM 1 8 7. 7MHz MEMORY : PRESS ADD / DLT KEY 1) Press CH to select the desired radio station.
*Important: If a remote control button does not work when pressed, press the FM button on the remote and try the button again. 3 1)Press to select FM ANTENNA. 2)Press SET to select “INT SET : SET SELECT : END : ACT I ON (INTERNAL)” or “EXT ■ For cable TV users (EXTERNAL)” to ➛ “INT” ■ For antenna users determine which one sounds best.
Timer Recording You can set up to 8 programs to be recorded while you are away. 1 2 Press PROG* to display SET PROGRAM screen. TIMER PROGRAMMING. T I MER PROGRAMM I NG ON T I MER SLEEP T I MER : 00 2) Press SET to display screen. SELECT : SET : SET END : PROG 3 to select 1) Press SET PROGRAM Ready Checklist All connections are made. Your unit is plugged in. The clock is set to correct time. The tape is long enough. The record tab is in place.
*Important: If a remote control button does not work when pressed, press the and try the button again. button on the remote Cancel a Timer Recording: (Recording is in progress) Review, Replace or Clear Program Contents : (Recording is not in progress) Hold down STOP for a few seconds to cancel the Timer Recording. 1 2 • Any future daily or weekly recordings will be performed as programmed. Repeat steps 1 and 2 on page 30. Press to select the desired program.
Cable Box Universal Remote Control Feature Universal Remote Control is... The Remote Control may be set up to control some basic DSS or Cable box functions. The Universal Remote Control Setup 1 Find your DSS box or Cable box Brand Code Number from one of the charts on the next page. 2 Setup remote. Hold down DSS CABLE and press number keys to enter code. • If code number is 100 or greater, e.g., press 1 - 0 - 2 for 102. 3 Confirm code entry. Press POWER* to turn selected unit ON or OFF.
*Important: If a remote control button does not work when pressed, press the the remote and try the button again. , DVD, FM button on DSS Brand Code Numbers Toshiba ........................................................... 90 Hitachi/ Hughes ........................................ 91, 99 Primestar ........................................................ 92 Drake .............................................................. 93 Magnavox ................................................. 94, 95 Uniden ...
Tape Operation Search System is ... Each time a recording is made, an invisible index mark is placed on the tape. When timer recordings are made, program index and information are also included. These index marks can be used to access or scan recordings. Index Search Go directly to the desired recording. 1 Press SEARCH* in Playback or Stop mode to display INDEX SEARCH screen, and then press number keys to select the recording number.
*Important: If a remote control button does not work when pressed, press the and try the button again. button on the remote Program End Search Locates end point of recording for continuity. 1 2 Press SEARCH twice in Playback or Stop mode to display PROGRAM END SEARCH screen . Press FF to start search. PROGRAM END SEARCH To cancel, press PLAY or STOP. SEARCH START : FF EX I T : SEARCH Example of Program End Search operation. Fig.
Tape Operation (continued) Repeat Play Set to see a recording over and over. PLAY REPEAT ON To turn “ON,” press PLAY/REPEAT on the unit repeatedly in Play mode to select “REPEAT ON”. To turn “OFF,” repeat above to select “REPEAT OFF.” • Playback repeats when tape end is reached or an unrecorded portion longer than 30 seconds is detected. PLAY/REPEAT Note • For repeat play in DVD mode, see page 55. Zero Search To quickly return to a specific tape counter location.
*Important: If a remote control button does not work when pressed, press the and try the button again. button on the remote Auto Operation Functions ■ Auto Shut Off No broadcast signal in TV mode (Only when Weak Signal Display is set to OFF.), DVD stops, or blank tape is played for 5 minutes ➛ Power turns off • This feature is canceled if any button is pressed during above conditions. ■ Auto Playback Insert a tape in Power off mode ➛ Power turns on • Playback begins if tape has no record tab.
Special VCR Features Channel Caption is ... Channel Caption 1 2 Press ACTION* to display MAIN MENU.
*Important: If a remote control button does not work when pressed, press the and try the button again. Weak Signal Display Feature Ready Checklist It is necessary to enter TV mode by pressing before selecting “CH” on the MAIN MENU. Remote Warning Feature When Universal Remote Control (page 32) is used, and this feature is set to “ON,” a warning appears whenever an invalid key is pressed in DSS or Cable mode. 1 2 1) Press to select “TV.” 2) Press SET to display SET UP TV screen.
V-Chip Control Feature V-Chip Control Feature is... This unit has a built-in V-Chip Control which allows you to block unwanted TV usage based on US MOVIES and US TV PROGRAMS Ratings. Process of V-Chip Control Feature Enter Code Setup Blocking Enter Secret Code A 4-digit code must be entered to view a blocked program or change rating settings. 1 2 Press ACTION* to display MAIN MENU.
*Important: If a remote control button does not work when pressed, press the and try the button again. If LOCK menu is not displayed, perform “Enter Secret Code” steps on page 40. button on the remote Process of V-Chip Control Feature Enter Code Setup Blocking US MOVIES Ratings 1 LOCK US MOV I ES : OFF CHANGE SETT I NGS : OFF US TV PROGRAMS CHANGE SETT I NGS : OFF DVD LOCK CHANGE SETT I NGS NEXT PAGE SELECT : SET : SET END : ACT I ON 1)Press to select US MOVIES. 2)Press SET to set “ON” or “OFF.
V-Chip Control Feature (continued) If LOCK menu is not displayed, do “Enter Secret Code” steps on page 40. Process of V-Chip Control Feature Enter Code Setup Blocking US TV PROGRAMS Ratings 1 LOCK US MOV I ES : OFF CHANGE SETT I NGS : OFF US TV PROGRAMS CHANGE SETT I NGS : OFF DVD LOCK CHANGE SETT I NGS NEXT PAGE SELECT : SET : SET END : ACT I ON • “NEXT PAGE” displays CANADIAN V-Chip setting menu. Not necessary except when viewing Canadian tapes or broadcasts.
*Important: If a remote control button does not work when pressed, press the and try the button again. button on the remote Process of V-Chip Control Feature Enter Code Setup Blocking Blocking Message • If a program or movie ABC exceeds the ratings you have set, a message PROGRAM RAT I NG EXCEEDED will appear on a black RAT I NG : PG-1 3 background and sound ACCESS CODE ---is muted.
Audio Features Audio Mode for Playback With the proper audio mode setting, your unit can: • record and playback MTS stereo broadcast (main language) in stereo Hi-Fi. Stereo sound is See the “Playback a Tape” section on recorded on the left and right page 18 to playback the tape. audio tracks and on the video portion of a tape.
*Important: If a remote control button does not work when pressed, press the and try the button again. button on the remote DVD Volume Adjust Audio recorded on a DVD or Video CD often incorporates a dynamic range of sound. This means that, when compared to a music CD, etc., the average volume is generally lower and the peaks may be higher. This unit can be set so that the volume is increased automatically. 1 2 Press ACTION* to display MAIN MENU.
Video / Audio Menu *Important: If a remote control button does not work when pressed, press the button on the remote and try the button again. This feature allows easy setting of picture and sound suitable for each program source. Video Menu 1 2 Audio Menu Press ACTION* to display MAIN MENU.
Video / Audio Adjustment Video Adjustment 1 2 Press ACTION to display MAIN MENU.
Disc Operation Subtitle Language (DVD only) You can select a different subtitle language (if offered) than the one set at the Settings for DVD Operation. (See page 58.) 1 Press SUB TITLE* in Play mode to display the subtitle selection on-screen. 2 Te amo Ready Checklist Please read “Basic DVD Operation” on page 20. [Subtitle language (No.)] [Audio soundtrack language (No.)] ENG English • Display disappears after 5 seconds.
*Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. When appears on the screen while a button is being pressed, it means that the corresponding operation is prohibited by the unit or the disc. Multiple Angle Viewing (DVD only) DVDs may contain scenes shot from multiple camera angles allowing the same scene to be viewed at different angles. You can view these angles, if available, using the ANGLE button.
Disc Operation (continued) Title menu (DVD only) Some DVDs have more than one title, e.g. movies. If the disc offers a title menu, you can select the desired title number. (Operation may vary according to the disc.) 1 Press TITLE* in Play mode to Cas t l es display title screen. T I TLE MENU Dogs B i r ds Love r s 2 T I TLE MENU Dogs Cas t l es Love r s B i r ds B i rds of the world • Pressing TITLE again resumes play from the scene when TITLE was first pressed.
*Important: If a remote control button does not work when pressed, press the and try the button again. Program Play (Video CD/CD) You can program specific tracks and order of play. 1 2 Press ACTION in Stop mode to display MAIN MENU. M A I N MENU 1) Press to select “DVD.” LOCK LANGUAGE DVD 2) Press SET to 53 display screen. CH TV CLOCK 1 SELECT : END : ACT I ON 3 SET : SET 1) Press to select “PLAY MODE.” 2) Press SET to display screen.
Disc Operation (continued) *Important: If a remote control button does not work button on when pressed, press the the remote and try the button again. Random Play (Video CD/CD) Tracks are played in a random order. 1 2 Press ACTION* in Stop mode to display MAIN MENU. M A I N MENU DVD LOCK LANGUAGE 53 TV SELECT : END : ACT I ON 3 SET : SET DVD MAIN MENU SELECT SET END 4 : : SET : ACTION PLAY MODE SELECT SET END 1 CH CLOCK 1) Press to select “DVD.” 2) Press SET to display screen.
ntrol button does not work button on , press the d try the button again. DVD Operation using On-Screen Displays When DISPLAY is pressed, On-Screen Displays show disc information (title/chapter/track number, elapsed playing time) and unit information (Repeat play, Play mode). 1 Ready Checklist Unit is in DVD mode, press DVD. Press DISPLAY in Play or Stop mode to display “On-Screen Display.” • Each press of DISPLAY changes the on-screen display as follows. (Please refer to page 54 or 55.
DVD Operation using On-Screen Displays (continued) Detailed Descriptions of Each On-Screen Display Disc information screen (for DVD) 1. TITLE No. • Change the No. by pressing keys, and press SET. * or the NUMBER 1 2 T I TLE : 1 CHAPTER : 12 DVD 1 : 12 : 55 3 4 2. Chapter No. • Change the No. by pressing keys, and press SET. or the NUMBER SELECT : SET : SET 3. Disc currently being played 4. Elapsed playing time NEXT : DISPLAY The screen may be changed by selecting the elapsed time.
*Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Detailed Descriptions of Each On-Screen Display Unit information screen • Change the desired mode during play by pressing , and press SET. a. Repeat Play DVD CHAPTER REPEAT Video CD/CD TRACK REPEAT TITLE REPEAT DISC REPEAT REPEAT OFF REPEAT OFF a PLAY CHAPTER REPEAT SELECT : SET : SET END : DISPLAY b. Play mode [Video CD/ CD only] (See page 51 or 52.
MP3 Playback Operation MP3 Playback You can use this unit to play MP3 format audio recorded for personal use with a computer etc. onto a CD-R or CD-RW. Play may not be possible in some cases due to the condition of the recording. ■ MP3 playback (During STOP mode) 1) Press to select an MP3 file ( ). 2) Press SET or PLAY to start playback. 1 2 3 ■ Select folder (During STOP mode) 1) Press to select a folder ( ). 2) Press SET to display files/folders contained in the folder.
DVD Lock Feature *Important: If a remote control button does not work when , DVD button on the pressed, press the remote and try the button again. You can prevent playback of DVDs with a specific rating level which may be unsuitable for children. • Some DVDs are encoded with a rating level. If the disc rating is higher (stricter) than the one you preset, playback will be prohibited. Caution Discs not encoded with a rating level will play even if the jacket states it is for mature audiences.
Settings for DVD Operation 1 2 Press ACTION* in Stop mode to display MAIN MENU. M A I N MENU DVD LOCK LANGUAGE 53 TV SELECT : END : ACT I ON 3 1 CH CLOCK SET : SET DVD MAIN MENU DISC LANGUAGES AUDIO OUTPUT ST I L L MODE : AUTO TV MODE : Letterbox SELECT SET END 1) Press to select “DVD.” 2) Press SET to display screen. Once initial settings are done, they remain in memory (even after the power is off) until changed.
*Important: If a remote control button does not work when pressed, press the remote and try the button again. , DVD button on the AUDIO OUTPUT Select the digital output to be output from the optical digital audio output connector of the unit. 1 2 Do steps 1 and 2 on page 58. DVD MAIN MENU DISC LANGUAGES AUDIO OUTPUT ST I L L MODE : F I ELD TV MODE : Letterbox SELECT SET END 3 : : SET : ACTION AUDIO OUTPUT LPCM(DVD) Dolby Digital dts DRC SURROUND SELECT SET END 1) Press to select “AUDIO OUTPUT.
Settings for DVD Operation (continued) STILL MODE Set to reduce jitter in a displayed still picture or a motion picture. 1 2 *Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Do steps 1 and 2 on page 58. DVD MAIN MENU DISC LANGUAGES AUDIO OUTPUT ST I L L MODE : F I ELD TV MODE : Letterbox SELECT SET END : : SET : ACTION 1) Press * to select “STILL MODE.” 2) Press SET repeatedly for mode.
Language Code List Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE” and/ or “MENUS” (see page 58).
Before Requesting Service Check the following points once again if you are having trouble with your unit. Power Correction No power… • Completely insert Power Plug into an AC outlet. • Set POWER button to ON. Power turns itself off... • Auto power-off (shut off) occurs after about 5 min. in DVD mode with no operation, or if there is no broadcast signal in TV or Playback mode. Turn the power back on. (P. 21, 37) Monitor Correction No picture or sound...
DVD/Video CD/CD Correction Play fails to start even when PLAY is pressed... • This unit cannot play discs other than DVDs, Video CDs and CDs. • The disc may be dirty and require cleaning. Play starts but then stops immediately... • Be sure disc is installed with label side up. Picture is distorted during rapid advance or rapid reverse... • The picture will be somewhat distorted at times: this is normal. No Forward/Reverse search play...
Warning and Instruction Displays Check the following points once again if you are having trouble with your unit. OSD Caution Page PLEASE SET CLOCK BEFORE PROGRAMMING If you attempt to set or review a Timer Recording or set the On-Timer and the Clock is not set... 16, 17 CHECK CASSETTE RECORD TAB If you press REC, and a cassette is inserted with no record tab... TO CANCEL TIMER REC HOLD DOWN STOP KEY FOR APPROX 3 SEC If you press STOP during a Timer Recording...
s it. Page OSD Caution VIDEO HEADS MAY NEED CLEANING PLEASE INSERT HEAD CLEANING CASSETTE OR REFER TO MANUAL END: PLAY If head cleaning becomes necessary while playing back a tape... VCR LOCK ACTIVATED PLEASE CHECK THE DISC, AND FOR STAINS OR SCRATCHES ON DISC IT IS PROHIBITED TO COPY DVD/ VIDEO CD/CD TO VHS 6 If you press a function button other than STOP/EJECT or POWER while the unit is in VCR Lock mode...
Index TV / VCR A Accessories ............................................... 4 B C D E F AC Power Plug ......................................... 11 ACTION button .................................... 8, 16 ADD / DLT / CLEAR button ................. 8, 17 Audio Adjustment ..................................... 47 Audio Auto Gain Control (AGC) ............... 46 AUDIO button ....................................... 8, 23 Audio Connections ................................... 12 Audio Features ...............
TV / VCR T Table of Contents ....................................... 5 Tape Erasure Prevention .......................... 4 Tape Operation ................................. 34 - 37 Timer Program Review, Replace, Clear ... 31 Timer Recording ...................................... 30 Timer Recording Cancellation ................. 31 Time Zone Adjust ..................................... 17 TRACKING / V-LOCK buttons .............. 6, 8 TV Operation ............................................
Broadcast & Digital Systems Company Panasonic Broadcast & Television Systems Company Division of Matsushita Electric Corporation of America Executive Office: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000 Eastern Zone: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621 Central Region: 1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200 Western Zone: 3330 Cahuenga Blvd W, Los Angeles, CA 90068 (323) 436-3500 Government Marketing Department: 52 West Gude Drive, Rockville, MD 20850 (30