Lap-Top Editor AJ- P Operating Instructions Use the dedicated AJ-B95 AC adapter.
IMPORTANT “Unauthorized recording of copyrighted television programs, video tapes and other materials may infringe the right of copyright owners and be contrary to copyright laws.” CAUTION: CAUTION TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.
Contents Features . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Cut editing operations . . . . . . . . . . . . . .56 Assemble editing . . . . . . . . . . . . . . . . . . . . . . . . .56 Insert editing . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 Storing the edit points . . . . . . . . . . . . . . . . . . . . .57 Preview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 Executing editing . . . . . . . . . . . . . . . . . . . . . . . . .59 Review . . . . . . . . . . . .
Contents Sending (DUMP) and loading (LOAD) edit data to an external component . . . . . . .81 Superimposed screen . . . . . . . . . . . . . . .85 Error messages . . . . . . . . . . . . . . . . . . . .86 Video head cleaning . . . . . . . . . . . . . . . .88 Condensation . . . . . . . . . . . . . . . . . . . . .88 Maintenance . . . . . . . . . . . . . . . . . . . . . . .88 Specifications . . . . . . . . . . . . . . . . . . . . .
Features Functional input/output interfaces O Analog input and output facilities: Both VTRs come with video (composite/component) and audio input and output connectors. Analog video signals cannot be input in the 625i mode. O 9P remote connector: (525i mode only) Both VTRs come with 9P remote connectors to enable an external controller to operate the unit by remote control. The 9P remote connector of VTR1 can be switched to remote OUT, and an external VTR can be controlled using the control system of VTR1.
Opening and closing the top panel Opening the top panel Closing the top panel the top part of the lever forward to release the the top panel down to close it and engage 1 Pull 1 Push lock. the bottom part of the lever. both sides of the top panel, and lift the panel the bottom part of the lever now engaged, 2 Clasp 2 With to open it. push up the top part of the lever to lock it. Do not try to lift the panel by pushing the lever up.
Parts and their functions 1 1 LEVEL 2 3 4 BACKLIGHT · BACKLIGHT LIGHT DARK OFF LIGHT DARK OFF BRIGHTNESS BRIGHTNESS COUNTER/ REMAIN COUNTER/ REMAIN EVENT CH CONDITION CH CONDITION METER FULL/ FINE RESET METER FULL/ FINE 2 3 4 RESET CTL CTL V1 TC V2 TC UB CONTROL EJECT VTR 1 PREROLL SYNCHRO REMOTE 7 LOCAL 5 EXT VTR 3 CF ON OFF MODE TAPE EE TC REGEN R-RUN F-RUN VTR 2 REC INHIBIT TC MODE ON TAPE OFF EE REGEN R-RUN F-RUN REC INHIBIT ON OFF 2 CH 4 CH UB OPERATION
Parts and their functions LEVEL BACKLIGHT LIGHT DARK OFF BRIGHTNESS BRIGHTNESS COUNTER/ REMAIN COUNTER/ REMAIN EVENT CH CONDITION CH CONDITION METER FULL/ FINE RESET 6 METER FULL/ FINE RESET CTL 5 6 CTL V1 TC 7 9 BACKLIGHT LIGHT DARK OFF 5 · CONTROL EJECT 8 V2 TC UB VTR 1 PREROLL SYNCHRO REMOTE 7 LOCAL 5 EXT VTR 3 CF ON OFF MODE TAPE EE TC REGEN R-RUN F-RUN VTR 2 REC INHIBIT TC MODE ON TAPE OFF EE REGEN R-RUN F-RUN REC INHIBIT ON OFF 2 CH 4 CH UB OPERATION
Parts and their functions 1 5 2 3 6 7 9 : INPUT SCH CF SERVO REF SCH EDIT REC INH 525 625 W CTL SDI TOTAL REMAIN - dB 30 20 16 12 8 4 0 30 20 16 12 8 4 0 CH 1 CH 2 CH 3 CH 4 TC DF UB 4 ; - dB 8 Counter display area 1 “Cassette inside” display This lights when a cassette has been inserted. It flashes when the unit is in the STANDBY OFF mode. 8 625 lamps This lights when the 625i TV system has been selected. 9 Operation modes : For normal playback and recording.
Parts and their functions A @ > ? < INPUT SCH CF SERVO REF SCH EDIT REC INH 525 625 W CTL SDI TOTAL REMAIN - dB CH 3 CH 4 TC DF UB - dB B C 30 20 16 12 8 4 0 30 20 16 12 8 4 0 30 20 16 12 8 4 0 30 20 16 12 8 4 0 CH 1 CH 2 = D Counter display area D Audio level meter < TOTAL lamp This lights when the total editing time is displayed. - dB CH 1 CH 2 = REMAIN lamp This lights when the remaining tape amount is displayed. CH 3 CH 4 - dB > W lamp This lights in the wide-screen mode.
Parts and their functions E H IN F OUT IN AV SP OUT F G Counter display area E Event number display lamps This unit controls up to 200 sets of edit data (001 to 200) in the form of 3-digit event numbers. One of the following displays appears depending on the editing status. n###: Indicates that the No.### event is a new event which has not been stored on the EDL (edit list). (New event) d###: Indicates that the No.### event is an event which has been deleted from the EDL. ###: Indicates that the No.
Parts and their functions CONTROL PREROLL SYNCHRO REMOTE 7 LOCAL 5 EXT VTR 3 1 2 CF ON OFF VTR 1 MODE REGEN R-RUN F-RUN TAPE EE 3 TC 4 5 VTR 2 REC INHIBIT MODE ON TAPE OFF EE 6 TC REGEN R-RUN F-RUN 4 REC INHIBIT 2 CH 4 CH ON OFF 5 OPERATION V2 ANALOG EDIT MODE VIDEO IN IN AUDIO OUT SDI 2 CH INT V1-V2 V1 4 CH EXT V2 ANALOG SEPARATE 6 Panel switch area 1 CONTROL switch REMOTE: For controlling the unit from the REMOTE connector (9P).
Parts and their functions CONTROL PREROLL SYNCHRO REMOTE 7 LOCAL 5 EXT VTR 3 CF ON OFF VTR 1 MODE TAPE EE TC REGEN R-RUN F-RUN VTR 2 REC INHIBIT MODE ON TAPE OFF EE TC REGEN R-RUN F-RUN REC INHIBIT ON OFF 2 CH 4 CH OPERATION V2 ANALOG EDIT MODE VIDEO IN IN AUDIO OUT SDI 2 CH INT V1-V2 V1 4 CH EXT V2 ANALOG SEPARATE 7 8 9 : Panel switch area 7 ANALOG AUDIO IN switch Used to set the allocation of the audio signals to the 4 analog audio input connectors (on the rear panel).
Parts and their functions 1 2 CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX 3 CH 1 CH 2 CH 3 CH 4 MIX 4 3 UNI V1/V2 V1 2 MIX 1 L ASMBL 4 3 2 ANALOG MIX V 1ST EDIT VAR IN DELETE LAST X 7 DUMP LAST ED TOTAL ~ 9 DIAG 4 LIST DUR 8 SET UP 1 OUT 5 CORCT 3 LOAD T SET A4 REC CH 2 CH 3 AUTO EDIT GO TO OUT MULTI STOP REVIEW VTR 1 STILL DISP C EXIT ENTER V2 PB SDI REC REW FF VAR MIX PREVIEW STB OFF MIX 4 3 4 3 2 2 MIX 1 MIX 4 3 2 MIX 1 MIX
Parts and their functions CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 UNI V1/V2 MIX 4 3 3 2 2 MIX 1 L ANALOG ASMBL 4 V1 MIX V 1ST EDIT DELETE LAST X 7 1 LAST ED TOTAL ~ 9 DIAG 4 DUMP DUR 8 SET UP LIST OUT 5 CORCT 2 3 LOAD T SET TC REC CH 2 CH 3 0 C EXIT ENTER V2 PB AUTO EDIT SDI REC GO TO OUT MULTI PLAY STILL STOP STB OFF REW FF VAR MIX PREVIEW REVIEW VTR 1 4 MIX 4 3 4 3 2 2 MIX 1 MIX 4 3 2 MIX 1 MIX 4 3 2 MIX
Parts and their functions CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 UNI V1/V2 MIX 4 3 3 2 2 MIX 1 L ANALOG ASMBL 4 V1 MIX V 1ST EDIT IN LAST X 7 ~ 9 DIAG 4 5 CORCT 1 DUMP DUR TOTAL 8 SET UP LIST OUT LAST ED 3 LOAD T SET TC REC CH 2 CH 3 0 C EXIT ENTER V2 PB SDI REC AUTO EDIT PREVIEW MULTI REVIEW VTR 1 4 PLAY STILL STOP STB OFF REW FF VAR MIX MIX 4 3 4 3 2 1 MIX 4 3 2 MIX 1 MIX 4 3 2 MIX 2 MIX MIX 1 1 ANALOG
Parts and their functions 12 4563 CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 MIX 4 3 UNI V1/V2 V1 2 MIX 1 L ASMBL 4 3 2 ANALOG MIX V 1ST EDIT VAR IN DELETE LAST X 7 DUMP LAST ED TOTAL ~ 9 DIAG 4 LIST DUR 8 SET UP 1 OUT 5 TRACK 2 3 LOAD T SET A4 REC CH 2 CH 3 AUTO EDIT GO TO OUT MULTI PREVIEW STOP REVIEW VTR 1 STILL STB OFF REW FF 7 DISP C EXIT ENTER V2 PB VAR MIX MIX 4 3 4 3 2 2 MIX 1 MIX 4 3 2 MIX 1 MIX 4
Parts and their functions 9:; CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 MIX 4 3 UNI V1/V2 V1 2 MIX 1 L ASMBL 4 3 2 ANALOG MIX V 1ST EDIT VAR IN DELETE LAST X 7 DUMP LAST ED TOTAL ~ 9 DIAG 4 LIST DUR 8 SET UP 1 OUT 5 CORCT 3 LOAD T SET BS A4 AUTO EDIT GO TO OUT MULTI SPLIT MARK IN TC REC CH 2 CH 3 STILL DISP C EXIT ENTER V2 PB SDI REC REW VAR FF MIX PREVIEW STOP STB OFF 8 MARK OUT + 1 MIX 4 3 2 MIX VTR 2 4 3
Parts and their functions <= > CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 MIX 4 3 UNI V1/V2 V1 2 MIX 1 L ASMBL 4 3 2 ANALOG MIX V 1ST EDIT VAR IN DELETE LAST X 7 DUMP LAST ED TOTAL ~ 9 DIAG 4 LIST DUR 8 SET UP 1 OUT 5 CORCT 3 LOAD T SET A4 REC CH 2 CH 3 AUTO EDIT GO TO OUT MULTI STOP REVIEW VTR 1 STILL DISP C EXIT ENTER V2 PB SDI REC REW FF VAR MIX PREVIEW STB OFF MIX 4 3 4 3 2 2 MIX 1 MIX 4 3 2 MIX 1 MIX 4
Parts and their functions ?@AB C CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 MIX 4 3 UNI V1/V2 V1 2 MIX 1 L ASMBL 4 3 2 ANALOG MIX V 1ST EDIT VAR IN DELETE LAST X 7 DUMP LAST ED TOTAL ~ 9 DIAG 4 LIST DUR 8 SET UP 1 OUT 5 CORCT 3 LOAD T SET A4 REC CH 2 CH 3 AUTO EDIT GO TO OUT MULTI STOP REVIEW VTR 1 STILL DISP C EXIT ENTER V2 PB SDI REC REW FF VAR MIX PREVIEW STB OFF MIX 4 3 4 3 2 2 MIX 1 MIX 4 3 2 MIX 1 MIX
Parts and their functions F D E CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 MIX 4 3 UNI V1/V2 V1 2 MIX 1 L ASMBL 4 3 2 ANALOG MIX V 1ST EDIT VAR IN DELETE LAST X 7 DUMP LAST ED TOTAL ~ 9 DIAG 4 LIST DUR 8 SET UP 1 OUT 5 CORCT 3 LOAD T SET A4 REC CH 2 CH 3 AUTO EDIT GO TO OUT MULTI STOP REVIEW VTR 1 STILL DISP C EXIT ENTER V2 PB SDI REC REW FF VAR MIX PREVIEW STB OFF MIX 4 3 4 3 2 2 MIX 1 MIX 4 3 2 MIX 1 MIX 4
Parts and their functions CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 UNI V1/V2 MIX 4 3 3 2 2 MIX 1 L ANALOG ASMBL 4 V1 MIX V 1ST EDIT DELETE LAST X 7 DUMP LAST ED TOTAL ~ 9 DIAG 4 LIST DUR 8 SET UP 1 OUT 5 TRACK 2 3 LOAD T SET TC REC CH 2 CH 3 0 C EXIT ENTER V2 PB AUTO EDIT SDI REC GO TO OUT MULTI PLAY STILL STOP STB OFF REW FF VAR MIX PREVIEW REVIEW VTR 1 4 MIX 4 3 4 3 2 2 MIX 1 MIX 4 3 2 MIX 1 MIX 4 3 2 MIX
Parts and their functions 5 COARSE SC FINE SYSTEM 4 H 3 CHROMA LEVEL HUE 2 SET UP 1 VIDEO LEVEL VTR1 controls (side panel) Encoder control area (VTR1) Encoder and systems adjustments can be performed using these controls for the video signals to be output to an external device. The VTR2 controls are positioned symmetrically to the VTR1 controls. 1 VIDEO LEVEL control Used to adjust the video level of the video output signals.
Parts and their functions 1 5 VIDEO/Y NOT USER SERVICEABLE 6 VIDEO IN PB PR 7 5 REMOTE VIDEO/Y 6 VIDEO IN PB 7 PB VIDEO MON OUT PR TC OUT VIDEO OUT V 2 PB SDI IOUT 8 A U D I O I N CH 1 CH 2 V T VIDEO R MON 1 OUT PR CH 3 (CH 1•3) CH 4 (CH 2•4) L 9 CH 2 (CH 2/4) REF IN 75Ω AUTO DC IN CH 3 (CH 1/3) CH 4 (CH 2/4) R A U D I O M O N MIC A CH 1 U (CH 1/3) D I O O U T TC IN 4 TC OUT VIDEO OUT SDI IN ACTIVE THROUGH V 1 / V 2 VIDEO/Y 3 REMOTE PR EDL V T R VIDEO/Y 2 2
Parts and their functions < VIDEO/Y NOT USER SERVICEABLE VIDEO IN PB VIDEO/Y REMOTE PR VIDEO IN PB REMOTE PR TC IN EDL V T R VIDEO/Y 2 PB VIDEO MON OUT PR VIDEO/Y TC OUT VIDEO OUT PB ACTIVE THROUGH V 1 / V 2 SDI IOUT A U D I O I N CH 1 A CH 1 U (CH 1/3) D I O O U T CH 2 PR TC OUT VIDEO OUT SDI IN V 2 V T VIDEO R MON 1 OUT CH 3 (CH 1•3) CH 4 (CH 2•4) L CH 3 (CH 1/3) CH 4 (CH 2/4) R MIC CH 2 (CH 2/4) A U D I O M O N O U T (V2) (V1) ; Connector area ; SDI input/output c
Parts and their functions = VIDEO/Y NOT USER SERVICEABLE VIDEO IN PB PR > ? REMOTE VIDEO/Y @ VIDEO IN PB REMOTE PR TC IN EDL V T R VIDEO/Y 2 PB VIDEO MON OUT PR TC OUT VIDEO OUT V 2 PB SDI IOUT A U D I O I N CH 1 CH 2 V T VIDEO R MON 1 OUT PR CH 3 (CH 1•3) CH 4 (CH 2•4) L CH 2 (CH 2/4) 75Ω AUTO DC IN CH 3 (CH 1/3) CH 4 (CH 2/4) R A U D I O M O N MIC A CH 1 U (CH 1/3) D I O O U T REF IN TC OUT VIDEO OUT SDI IN ACTIVE THROUGH V 1 / V 2 VIDEO/Y O U T (V2) (V1) Conn
Parts and their functions E VIDEO IN PB VIDEO/Y NOT USER SERVICEABLE VIDEO/Y REMOTE PR VIDEO IN PB REMOTE PR TC IN EDL V T R VIDEO/Y 2 PB VIDEO MON OUT PR VIDEO/Y TC OUT VIDEO OUT PB PR ACTIVE THROUGH V 1 / V 2 SDI IOUT A U D I O I N CH 1 CH 2 VIDEO OUT CH 3 (CH 1•3) CH 4 (CH 2•4) L CH 2 (CH 2/4) 75Ω AUTO CH 3 (CH 1/3) CH 4 (CH 2/4) R A U D I O M O N MIC A CH 1 U (CH 1/3) D I O O U T REF IN TC OUT SDI IN V 2 V T VIDEO R MON 1 OUT O U T (V2) A (V1) B C D F Con
Parts and their functions Connector area Setting method Setting is possible when “V1+V2” has been selected as the setup menu item No.772 (AUTO MONI) setting. EF AUDIO MONITOR OUT connectors (XLR) These are the audio monitor output connectors. Their output signals can be changed by setting the AUDIO MONITOR SELECT switches.
Setup menu operations holding down the SHIFT button, turn the dial 4 While and change the value.
Setup menu operations User memory and factory settings This unit has a user memory function in which users can store settings. If a particular set of settings is stored, they can be recalled altogether. It is also possible to recall the factory settings in one go. (The TC PRESET and UB PRESET values can neither be stored nor recalled.) Storing settings in the user memory Recalling the factory settings (menu reset) the SET UP ([SHIFT] + [7]) button to set the 1 Press unit to the setup mode.
Setup menus SYSTEM menu Item No. 11 Superimposed display SYS SC No. 0000 0255 VIDEO PHASE 0000 0032 0064 16 AV PHASE 0000 0090 0180 17 SYS H RANGE 0000 0001 18 70 [ [ [ [ [ [ This selects the SYSTEM H variable range. FULL 0: ±8 µs FINE 1: –2.0 µs to +2.7 µs [ [ This selects the SYSTEM H center position. 0: –13.4 µs 1: –8.96 µs 2: –4.52 µs 3: 0 µs 4: +4.52 µs 5: +8.96 µs 6: +13.4 µs [ [ –127 This is for adjusting the system phase. The total variable range is at least ±180 degrees.
Setup menus BASIC menu Item No. 001 Superimposed display V T R 1 V T R 2 [ [ [ [ This selects whether the REMAIN (remaining tape time) display is to be superimposed on the MONITOR OUT connectors and liquid crystal monitor screen. OFF 0: REMAIN display is not shown. ON 1: REMAIN display is shown. OREMAIN display is not shown when the tape has been ejected [ or when the remaining tape time is calculated after the tape has been inserted.
Setup menus OPERATION menu Item No. 100 Superimposed display Setting No. Superimposed display SEARCH ENA 102 103 [ [ 0000 0001 0002 This selects the maximum speed of fast forwarding and rewinding. x16 0: 16 times normal speed [ x32 1: 32 times normal speed x50 2: 50 times normal speed [ This selects the status to be established until the audio signals are output when the unit has transferred from the STOP mode or search mode to the PLAY mode.
Setup menus OPERATION menu Item No. Superimposed display 110 MEMORY STOP Setting No. Superimposed display 0000 0001 170 HUMID OPE 0000 0001 171 ALL STOP SEL 0000 0001 172 VTR1 IN SEL 0000 0001 173 174 Description of setting This selects the processing to be conducted when the counter displays zeros in the CTL mode or during FF or REW. OFF 0: The VTR is not shut down. ON 1: The VTR is automatically shut down. OFor the stop mode, either the stop or still-picture (SHTL + 0.
Setup menus INTERFACE menu Item No. 202 Superimposed display Setting No. ID SEL 0000 0001 205 206 207 208 BAUD RATE Superimposed display This selects the ID information to be returned to the controller. OTHER 0: 20 25H (525i mode) is returned. DVCPRO 1: The DVCPRO’s own ID and F0 33H (525i mode) is returned. This operation is not performed in the 625i mode. 0000 0001 0002 0003 0004 1200 This selects the RS-232C (EDL) transfer (baud) rate.
Setup menus EDIT menu Item No. 303 Superimposed display No. STD/NON-STD 0001 0002 SERVO REF 0000 0001 305 [ This selects the servo synchronizing signals. AUTO 0: During recording or editing, the servo is synchronized with the input signals; during playback, it is synchronized with the REF signal. EXT 1: The servo is synchronized with the REF signal at all times.
Setup menus EDIT menu Item No. 311 312 313 315 Superimposed display Setting No. Superimposed display AUD EDIT IN [ 0000 0001 This selects how to join audio edit OUT points. CUT 0: Cut editing FADE 1: Fade editing [ AUD EDIT OUT AUTO ENTRY This selects whether a previous edit OUT point is to be registered automatically in the setting as the next edit IN point after automatic editing.
Setup menus EDIT menu Item No. 370 Superimposed display Setting No. BEEP 0000 0001 0002 0003 371 SV-UNLK EDIT 0000 0001 0002 372 Superimposed display This selects whether the confirmation tone is to be sounded. OFF 0: The confirmation tone does not sound. ENTRY 1: The confirmation tone is sounded when registering is performed or when an error or warning has occurred.
Setup menus EDIT menu Item No. 379 380 Superimposed display Setting No. Superimposed display 1ST-E TITLE This selects the title screen characters (3 lines a20 characters) which is to be superimposed onto the black burst signal during 1ST EDIT. Characters: ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789 ,.:;?!/ ’()+–±¢ = OThis item takes effect when ON has been selected as the setup menu item No.380 (1ST E-DISP) setting. OThis operation is not performed in the 625i mode.
Setup menus TAPE PROTECT menu Item No. 400 401 Superimposed display STILL TIMER No. 0000 0001 0002 0003 0004 0005 0006 0007 0008 SRC PROTECT DRUM STDBY 0000 0001 403 V T R 2 [ [ This selects the tape protection mode operation when the unit has been left standing in the STILL mode. STEP 0: Step (or step FWD in STILL mode).
Setup menus TIME CODE menu Item No. 500 Superimposed display Setting No. Superimposed display This selects whether to output the VITC signal at the positions which have been set by setup menu item No.501 (VITC POS-1) and No.502 (VITC POS-2). BLANK 0: The VITC signal is not output. THRU 1: The VITC signal is output. VITC BLANK 0000 0001 501 VITC POS-1 (525i mode) 10L This selects the position where the VITC signal is inserted. 16L The same line as the one selected by setup menu item No.
Setup menus TIME CODE menu V T R 1 V T R 2 [ [ 0000 0001 This selects whether the phase correction for the LTC generated by the TCG is to be controlled. OFF 0: Phase correction is not controlled. ON 1: Phase correction is controlled. [ [ 0000 0001 This selects the color framing flag into the TCG. OFF 0: The color framing flag is set to OFF. ON 1: The color framing flag is set to ON. [ [ This selects the CTL and TCG drop frame mode. DF 0: For operation in the drop frame mode.
Setup menus TIME CODE menu Item No. 571 Superimposed display Setting No. Superimposed display TC JUMP 0000 0001 0002 0003 572 V-MON/TC OUT 0000 0001 0002 573 574 Description of setting OFF VTR1 VTR2 ALL This selects the setting for TC jumping. 0: No TC jumping. 1: TC jumping on the VTR1 side only. 2: TC jumping on the VTR2 side only. 3: TC jumping on both the VTR1 and VTR2 sides.
Setup menus VIDEO menu V T R 1 V T R 2 [ [ [ [ 0000 0001 This selects ON or OFF for the closed caption signal of the first field. BLANK 0: Signal is forcibly blanked. THRU 1: Signal is not blanked. In the 625i mode, this setup menu item does not appear. [ [ 0000 0001 This selects ON or OFF for the closed caption signal of the second field. BLANK 0: Signal is forcibly blanked. THRU 1: Signal is not blanked. In the 625i mode, this setup menu item does not appear.
Setup menus VIDEO menu Item No. 614 Superimposed display Setting No. Superimposed display Pb/Pr OUT LV 0000 0001 618 INTERPOLATE 03 [ [ [ This selects the 7.5% setup processing for the input composite signal. THRU 0: The signal is recorded in its original form. CUT 1: The signal is recorded with the 7.5% setup removed. [ [ This selects the 7.5% setup processing for the output composite signal. THRU 0: The signal is output in its original form. ADD 1: The signal is output with the 7.
Setup menus VIDEO menu Description of setting V T R 1 V T R 2 For setting 7.5% setup processing to be performed on input and output signals in the 50 Mbps mode. (The 00, 01, 02 and 03 settings on the submenu can be displayed by pressing the STILL button. To return to this menu from the submenu, press the STILL button again.) In the 625i mode, this setup menu item does not appear. [ [ This selects the 7.5% setup processing for the input composite signal.
Setup menus VIDEO menu Item No. 670 Superimposed display No. V T R 2 This selects the video input. CMPST 0: Analog composite input CMPNT 1: Analog component input Analog video signals cannot be input in the 625i mode. [ [ This selects the video output.
Setup menus AUDIO menu Item No. Superimposed display 714 EMPHASIS 726 REC CUE Setting No. Superimposed display 0000 0001 OFF This selects emphasis for the audio signals. ON 0000 0001 0002 0003 0004 0005 727 CH1 CH2 CH1+2 CH3 CH4 CH3+4 PB FADE 731 732 This selects the input signals to be recorded on the cue track.
Setup menus AUDIO menu Item No. 770 Superimposed display Setting No. Superimposed display CUE INSERT 0000 0001 771 AUDIO SLOW 0000 0001 0002 772 AUTO MONI 0000 0001 773 Description of setting PB AUDIO SEL 0000 0001 V T R 1 This selects whether to record signals onto the cue track in the audio insert mode OFF 0: No signals are recorded on the cue track, and the already recorded signals are left on the track. ON 1: Signals are recorded on the cue track.
Setup menus LCD menu Item No. B00 Superimposed display Setting No. LCD MODE 0000 0001 0002 B01 LCD HUE Superimposed display This selects the LCD monitor screen displays. AUTO 0: During playback, the displays comply with the information on the recorded tape. During E-E (recording, etc.), they comply with the mode which has been set by setup menu items No.641 and No.643. WIDE 1: The displays are forcibly set to the wide-screen (16:9) mode.
Operation methods Recording external input signals using VTR1 Recording external input signals using VTR2 Analog component signals and analog composite signals can be input and recorded using VTR1. Recording with the 625i system is not possible. Analog component signals, analog composite signals and serial component digital signals can be input and recorded using VTR2. With the 625i system, only serial component digital signals can be recorded. the OPERATION MODE mode switch (page 1 Set 13) to SEPARATE.
Operation methods Playback using VTR1, VTR2 Analog component signals, analog composite signals and serial component digital signals can be played back and output using VTR1 and VTR2. the OPERATION MODE mode switch (page the VTR using the VTR1 or VTR2 button, 1 Set 8 Select 13) to SEPARATE. and press the PLAY button. AUTO as the setup menu item No.013 (PB stop playback, select the VTR whose playback 2 Select 9 To FORMAT) setting.
Preparing tapes for editing Before proceeding to commence editing, the black burst signal, time code and CTL signal must first be recorded on the tape. The method of preparing the editing tape differs depending on whether assemble editing or insert editing is to be performed. Preparing tapes for assemble editing In the case of assemble editing, a run-up period must be provided prior to the first assemble IN point. The 1ST EDIT function is available as an easy way of preparing the run-up period.
Preparing tapes for editing Recording editing titles (characters and symbols) Characters and symbols can be superimposed onto the video signals (black burst signals) and recorded for about 7 seconds after the start of 1ST EDIT, but this can be done only in the 525i mode. Recording the editing titles, editing dates, equipment numbers and other such information makes it easier to do post-editing work and conduct searches at a later date. the cursor with setup menu item No.
Preparing tapes for editing Preparing tapes for insert editing In the case of insert editing, the black burst signal, time code and CTL signal must be recorded for the whole editing period in addition to the run-up period for the assemble editing tape. Method using first edit (1ST EDIT) When T-END (tape end) is selected in step 2 for preparing tapes for assemble editing, 1ST EDIT recording continues until the tape end.
Cut editing operations Selecting the editing mode Insert editing: Assemble editing: all the buttons corresponding to the signals the ASMBL button. 1 Press 1 Press which are to be edited among the V, A1, A2, A3, In this mode, the video, audio (all channels) and A4 and/or TC buttons. time code are recorded at the same time. that the LEDs of the buttons concerned are 2 Check lighted. 2 Check that the ASMBL button LED is lighted.
Cut editing operations Storing the edit points There are three main ways to store edit points. 1. Use the search dial to search the editing screen, and set the edit point using the MARK IN or MARK OUT button. 3. Specify and set the length (duration of the editing period). the VTR whose edit points are to be set 1 Select using the VTR1 button or VTR2 button. the VTR whose edit points are to be set 1 Select using the VTR1 button or VTR2 button. setting the edit IN point, press the DUR 2 After button.
Cut editing operations Preview Preview is a rehearsal of the editing before the editing is performed for real. When the PREVIEW button is pressed, the event indicated by the event number display lamp is previewed. The pictures and sound produced when editing is actually performed will be played back as a simulation on the VTR2 monitor, enabling them to be checked out in advance. What is played back is the length of tape from the preroll point to the postroll point.
Cut editing operations Executing editing Press the AUTO EDIT button. Preroll point Edit IN point Edit OUT point Preroll time Review (rewind & play) Postroll point Postroll time ODuring assemble editing Postroll time AUTO EDIT Edit recording Playback Edit recording Review (rewind & play) ODuring insert editing Postroll time Edit recording Playback Review (rewind & play) Review Press the REVIEW ([SHIFT] + [PREVIEW]) button right after executing editing.
Split editing operations With insert editing, an audio IN point can be set slightly ahead of the video IN point. (Audio split editing) Similarly, a video IN point can be set slightly ahead of the audio IN point.
Editing without setting the edit IN point (park & edit) Editing can be performed without setting the VTR1 and VTR2 IN points. VTR1 and VTR2, and locate the places the AUTO EDIT button to proceed with 1 Operate 3 Press which will serve as the IN points. editing. the PREVIEW button. 2 Press The position where the PREVIEW button was To proceed with editing while skipping the preview, press the AUTO EDIT button in step 2 instead of the PREVIEW button, and proceed with editing.
Still-picture editing/slow-motion editing the IN point and OUT point of VTR1 (player) at VTR1 (player), and turn the search dial to 1 Set 3 Select the same position. run the tape at the actual desired speed. After VTR1 has been selected using the VTR1 button, press the MARK IN and MARK OUT buttons together to set the IN point and OUT point at the same position. In the case of still-picture editing, set the speed to 0a (SHTL 0, STILL). The slow-motion speeds that can be selected are 0a, 0.03a, 0.1a, 0.
Voice-over operations (1) Take the steps below to add sound (audio dubbing, voice-over) while watching the pictures played back. The sound to be recorded is first stored in the memory and then recorded on the tape by the steps described below so that the recording can be performed at the precise time at the location where the sound is to be added. 1 2 3 4 5 6 7 (The unit’s internal memory can store about 20 seconds of sound.) Sound can be recorded on CH1 and CH2 channels only.
Voice-over operations (1) CH 1 CH 2 CH 3 CH 4 V2 PB UNI SDI REC VAR 3 MIX 5 Select “2.” 4 MIX 4 MIX 4 MIX 3 3 3 3 2 2 2 2 MIX 1 MIX 1 MIX 1 MIX 4 1 V2 INPUT 4 < Select ANALOG.
Voice-over operations (2) Voice-over can also be performed by taking the steps below. Steps 1 through 7 are the same as for voice-over operations (1). 1 2 3 4 5 6 7 8 Select “INT_VO” as the setup menu item No.317 (AUD MEM MODE) setting. “m” now appears on the superimposed display of VTR2. (See page 85) 9 Select the channel (CH1, CH2) on which the sound is to be recorded with the setup menu item No.318 (AUD MEM CH) setting. Set the IN point and OUT point of the voice-over positions.
Audio cross channel editing Audio cross channel editing using the internal audio memory can be performed by connecting an external audio mixer. Sound can be recorded on CH1 and CH2 channels only. $ Example of operation Recording cross-faded audio signals onto CH2 INPUT A MIXER CH1 OUT INPUT B MIXER CH2 OUT Audio mixer AUDIO OUT (CH1 or CH2) AUDIO CH1 OUT AUDIO CH2 IN AUDIO CH1 IN Internal memory VTR1 VTR2 AJ-LT95 Process 1 “INT_X” as the setup menu item No.
Audio cross channel editing Process 2 the A1 button and turn off its lamp. The A2 the audio mixer in such a way that the 3 Operate 1 Press button LED remains lighted. VTR1 output signals (which are supplied to INPUT (CH1 audio insert is released and only CH2 audio insert editing is performed.) A of the audio mixer) are output from the MIXER CH1 OUT connector and the VTR2 CH1 output signals (input to INPUT B of the audio mixer) are output from the MIXER CH2 OUT connector.
Audio cross channel editing Step 1 (event 1) OUT point IN point CH1 CH2 Internal memory Approx. 20 sec Step 2 (event 2) CH2 IN point OUT point CH1 CH1 insert start Cross-fading by operating the audio mixer CH2 Portion recorded in step 1 Signals from the internal memory recorded here Signals from VTR1 (player) recorded here Internal memory Approx.
Checking the edit points (IN, OUT, DUR, GO TO) DUR OUT IN GO TO CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 UNI V1/V2 MIX 4 3 3 2 2 MIX 1 L ANALOG ASMBL 4 V1 MIX V 1ST EDIT DELETE LAST X 7 DUMP LAST ED TOTAL ~ 9 DIAG 4 LIST DUR 8 SET UP 1 OUT 5 CORCT 3 LOAD T SET TC REC CH 2 CH 3 0 C EXIT V2 PB AUTO EDIT SDI REC GO TO OUT MULTI PLAY STILL STOP STB OFF REW FF VAR MIX PREVIEW REVIEW VTR 1 4 MIX 4 3 4 3 2 2 MIX 1 MIX 4
Modifying and clearing edit data When an edit point has been set incorrectly, follow the method below to modify or clear the edit data.
Storing and recalling edit data The unit contains an EDL (edit decision list) memory for storing up to 200 events. Edit data can be stored in the EDL memory and, whenever the necessity arises, the required event data which has been registered can be recalled. It is also possible to modify recalled data, edit events one by one or perform multi-event editing.
Multi-event editing When multiple events have been stored, multiple events can edited together. the first of the events to be edited. (Refer to 1 Recall the section on storing and recalling edit data.) the MULTI ([SHIFT] + [AUTO EDIT]) button. 2 Press The data is automatically edited from the recalled event to the last event. The data of deleted events (events with “d” displayed before the 3-digit event numbers) are excluded from the data editing.
LAST X/LAST ED/TOTAL LAST X ([SHIFT]+[IN]) LAST ED ([SHIFT]+[OUT]) TOTAL ([SHIFT]+[DUR]) CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 MIX 4 3 UNI V1/V2 V1 2 MIX 1 L ASMBL 4 3 2 ANALOG MIX V 1ST EDIT VAR IN DELETE LAST X 7 DUMP LAST ED TOTAL ~ 9 DIAG 4 LIST DUR 8 SET UP 1 OUT 5 CORCT 3 LOAD T SET A4 REC CH 2 CH 3 AUTO EDIT GO TO OUT MULTI STOP REVIEW VTR 1 STILL DISP C EXIT V2 PB SDI REC REW FF VAR MIX PREVIEW STB OFF MIX 4
Setting the time code (T SET) This procedure is followed to set the initial value of the time code for manual recording or 1ST EDIT.
Setting the time code (T SET) When performing 1ST EDIT by setting the initial value of the time code When recording a time code whose initial value has been set during assemble editing or time code insert editing (VTR2 only) the cursor with setup menu item No.377 (1ST 1 Align EDIT TC). This can be done with open-ended editing where the editing is performed without the OUT point having been set. 2 Press the T SET ([SHIFT] + [3]) button.
Setting the time code (T SET) When performing assemble editing or time code insert editing by presetting the user’s bit the cursor with setup menu item No.574 (UB 1 Align PRESET). 2 Press the T SET ([SHIFT] + [3]) button. the numeric input buttons to input the desired 3 Use user’s bit value. 4 Press the ENTER button. Select “SW” as the setup menu item No.504 5 (REGEN MODE). the TC generator switch of VTR2 to R-RUN or 6 Set F-RUN. with the assemble editing or time code 7 Proceed insert editing.
CORCT/TRACK/DISP Correction function (CORCT) Track function (TRACK) This function enables corrections to be made to edit data in an existing event (one whose edit data has already been stored in the memory) but not in a new event. This function is used to set the edit points of VTR1 (player) efficiently in response to a change made in an edit IN point of the VTR2 (recorder). 1 Change the edit IN point of the VTR2 (recorder). the CORCT ([SHIFT] + [5]) button.
Clearing edit data in the EDL memory Clearing all the edit data 1 Press the EVENT button. the 9 button three times to show “999” on 2 Press the event number display lamps. the ENTER button while holding down the 3 Press SHIFT button. All the edit data inside the EDL memory area is now cleared. Similarly, it is possible to clear all the edit data inside the EDL memory area by pressing the [SHIFT] + [ALL STOP] + [C] buttons at the same time.
Encoder adjustments The video signals (ENCODER OUT) must be adjusted upon completion of the system connections before any signals are transmitted in order to conduct accurate error-free editing. (This adjustment may have to be repeated whenever a connecting cable is replaced or the connections changed.) To adjust the encoder using the laptop: the units as shown below.
Encoder adjustments the REMOTE/LOCAL switch to the position the SYSTEM PHASE controls. 2 Set 4 Adjust 1 Play back the standard color bars on VTR1. (LOCAL) where the adjustment is to be made. 2 Adjust the SYSTEM PHASE controls of VTR1. Adjust so that the waveform monitor (WFM) achieves the following. 1. In the INT mode, expand the waveform on the WFM to 0.1 µs. 2. Check the H SYNC position. 3. Now set the WFM to the EXT mode. 4.
Sending (DUMP) and loading (LOAD) edit data to an external component The edit data stored in the EDL memory can be sent to and loaded from an external component using the EDL connector on the unit’s rear panel. Outputting data to a computer, for instance, and loading data from a computer enables a wide range of systems to be run and managed in the following ways. O Data can be edited off-line by the unit, and the edit data can be used by an on-line system.
Sending (DUMP) and loading (LOAD) edit data to an external component Loading edit data from an external component External component settings and communication methods the communication parameters and format of 1 Set the data to be received using the INTERFACE The external component settings and data communication methods that must be employed differ depending on the component concerned.
Sending (DUMP) and loading (LOAD) edit data to an external component Concerning the EDL format Either the AG-A850 format or CMX340 format can be selected as the data format when edit data is to be sent to a personal computer or other external component. Select the format using the setup menu item No.271 (EDL FORMAT). $ AG-A850 format Since all the edit data in the EDL memory is sent in this format, the edit data can be completely restored when data which was sent from the unit is loaded again into the unit.
Sending (DUMP) and loading (LOAD) edit data to an external component $ CMX340 format O Some of the data is converted in this format so that it cannot be completely restored even when dumped data is loaded again. Event number: Deleted event numbers are packed and sent. During receiving, event numbers are ignored, and up to 200 events are received in sequence from the first event. Reel number: All reel numbers are received as “0001.
Superimposed screen Characters and symbols can be superimposed onto the output signals from the unit’s liquid crystal monitor or VIDEO MONITOR OUT connector. This superimpose function can be turned ON or OFF by pressing the DISP ([SHIFT] + [0]) button. The information to be superimposed and displayed can be selected using setup menu item No.002 (DISPLAY SEL). Information displayed on STATUS operating mode) line o m SHTL +32.
Error Messages One of the following error messages is displayed when a problem has occurred in the unit. The VTR is set to the auto OFF mode (stop) or the power is forcibly turned off. Contact your dealer if the error display persists even when the power is turned off and turned back on again. Display tube d Superimposed display Description VTR operation DEW Condensation (dew) has formed. Leave the power on and wait until the error message is cleared.
Error Messages Display tube Superimposed display E — 59 DRUM ROTA TOO SLOW This appears when the cylinder motor’s rotation speed is abnormally low. Auto OFF E — 59 DRUM ROTA TOO FAST This appears when the cylinder motor’s rotation speed is abnormally high. Auto OFF E — 61 CAP ROTA TOO SLOW This appears when the capstan motor’s rotation speed is abnormally low. Auto OFF E — 64 S REEL TOO FAST This appears when the supply reel motor’s rotation speed is abnormally high.
Video Head Cleaning This unit is equipped with an auto head cleaning function which automatically reduces the amount of dirt on the video heads. However, in order to maximize the unit’s reliability, it is recommended that the video heads be cleaned as and when appropriate. For further details on how to actually clean the heads, consult one of our service companies or your dealer.
Specifications [GENERAL] [VIDEO] $ Digital video (same for VTR1, VTR2) Supply voltage: DC 12 V Input current: 12 A Sampling frequencies: O DVCPRO 50 Y: 13.5 MHz PB/PR: 6.75 MHz O DVCPRO Y: 13.5 MHz PB/PR: 3.375 MHz Quantizing: 8 bits Video compression system: DCT + variable-length code Video compression ratios: O DVCPRO 50: 1/3.
Specifications [VIDEO] [AUDIO] $ Analog component IN/analog component OUT (same for VTR1, VTR2) $ Digital audio (same for VTR1, VTR2) Sampling frequency: 48 kHz Quantizing: 16 bits Frequency response: 20 Hz to 20 kHz ±1 dB (at reference level) Dynamic range: More than 85 dB (1 kHz, emphasis off, “A” weighted) Distortion: Under 0.
Specifications [INPUT/OUTPUT CONNECTORS] $ VIDEO $ AUDIO Analog component input: BNC a6 ([Y/PB/PR] a2) (VTR1, VTR2) Y: 1.0 V [P-P], 75 Ω, switched with analog composite input PB/PR: 0.525/0.757 V [P-P] switching, 75 Ω (75% color bar, 0% setup) Analog composite input: BNC a2 (VTR1, VTR2), 1.
Specifications [LCD MONITOR] LCD panel: 7-inch wide-screen TFT active matrix a2 (VTR1, VTR2), wide-screen/normal selectable (blank sides in normal mode), 525i/625i selectable Brightness adjustment: Controls a2 (VTR1, VTR2) Picture quality adjustment: Color, tint (separate on-screen display menus for left, right) (Tint: 525i mode only) Backlight selection: Bright, dark, off (separate switches for left, right) [SPEAKERS] Internal speakers a2 , VTR1/VTR2 selectable, L/STEREO/R selectable [DISPLAY TUBES] $ Co
PANASONIC BROADCAST & DIGITAL SYSTEMS COMPANY DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Executive Office: 3330 Cahuenga Blvd W.
Coordonnateur de montage portable AJ- P Manuel d’utilisation Utiliser l’adaptateur secteur AJ-B95 spécial.
Mise en garde: “L’enregistrement non autorisé d’émissions de télévision, films, rubans magnétoscopiques ou autres, protégés par des droits d’auteur, peut enfreindre les droits de propriété et aller à l’encontre des dispositions de la loi sur les droits d’auteur”. MISE EN GARDE: ATTENTION AFIN DE PRÉVENIR TOUT RISQUE D’INCENDIE OU DE CHOCS ÉLECTRIQUES, ÉVITER D’EXPOSER CET APPAREIL À LA PLUIE OU À UNE HUMIDITÉ EXCESSIVE.
Table des matières Caractéristiques . . . . . . . . . . . . . . . . . . . .5 Ouverture et fermeture du panneau supérieur . . . . . . . . . . . . . . . . . . . . . . . . . .6 Préparatifs du ruban pour le montage . . . . . . . . . . . . . . . . . . . . . . . .53 Préparatifs du ruban pour le montage par assemblage . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 Enregistrement des titres de montage (caractères et symboles) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table des matières Enregistrement et rappel des données de montage . . . . . . . . . . . . . . . . . . . . . . . . . .71 Montage multi-événements . . . . . . . . . .72 LAST X/LAST ED/TOTAL . . . . . . . . . . . .73 Réglage du signal de base de temps (T SET) . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 CORCT/TRACK/DISP . . . . . . . . . . . . . . . .77 Effacement des données de montage de la mémoire EDL . . . . . . . . . . . . . . . . . . . .78 Réglages du codeur . . . . . . . . . . . . . . . .
Caractéristiques Format compact et faible poids Ce coordonnateur de montage est un système de montage intégré qui renferme deux magnétoscopes numériques DVCPRO 50, un contrôleur de montage, deux moniteurs à cristaux liquides et des hautparleurs sous un même châssis. Il obéit à une conception compacte, légère et itinérante qui permet de le transporter en toute facilité et d’être prêt à effectuer tout travail de montage sur un bureau.
Ouverture et fermeture du panneau supérieur Ouverture du panneau supérieur Fermeture du panneau supérieur la partie supérieure du levier vers l’avant pour le panneau supérieur vers le bas pour le 1 Tirer 1 Pousser libérer le verrou. fermer et engager la partie inférieure du levier. les deux côtés du panneau supérieur et partie inférieure du levier étant engagée, 2 Saisir 2 La lever le panneau pour l’ouvrir.
Les commandes et leurs fonctions 1 1 LEVEL 2 3 4 BACKLIGHT · BACKLIGHT LIGHT DARK OFF LIGHT DARK OFF BRIGHTNESS BRIGHTNESS COUNTER/ REMAIN COUNTER/ REMAIN EVENT CH CONDITION CH CONDITION METER FULL/ FINE RESET METER FULL/ FINE 2 3 4 RESET CTL CTL V1 TC V2 TC UB CONTROL EJECT VTR 1 PREROLL SYNCHRO REMOTE 7 LOCAL 5 EXT VTR 3 CF ON OFF MODE TAPE EE TC REGEN R-RUN F-RUN VTR 2 REC INHIBIT TC MODE ON TAPE OFF EE REGEN R-RUN F-RUN REC INHIBIT ON OFF 2 CH 4 CH UB OPE
Les commandes et leurs fonctions LEVEL BACKLIGHT LIGHT DARK OFF BRIGHTNESS 6 BRIGHTNESS COUNTER/ REMAIN COUNTER/ REMAIN EVENT CH CONDITION CH CONDITION METER FULL/ FINE RESET METER FULL/ FINE RESET CTL 6 V2 TC UB CONTROL EJECT 8 5 CTL V1 TC 7 9 BACKLIGHT LIGHT DARK OFF 5 · VTR 1 PREROLL SYNCHRO REMOTE 7 LOCAL 5 EXT VTR 3 CF ON OFF MODE TAPE EE TC REGEN R-RUN F-RUN VTR 2 REC INHIBIT TC MODE ON TAPE OFF EE REGEN R-RUN F-RUN REC INHIBIT ON OFF 2 CH 4 CH UB OP
Les commandes et leurs fonctions 1 5 2 3 6 7 9 : INPUT SCH CF SERVO REF SCH EDIT REC INH 525 625 W CTL SDI TOTAL REMAIN - dB 30 20 16 12 8 4 0 30 20 16 12 8 4 0 CH 1 CH 2 CH 3 CH 4 TC DF UB 4 ; - dB 8 Section d’affichage du compteur 1 Affichage “Cassette insérée” Il s’éclaire lorsque la cassette est insérée. Il clignote lorsque l’appareil est en mode annulation d’attente (STANDBY OFF). 2 Voyant INPUT SCH INPUT s’éclaire lorsque les signaux vidéo sont envoyés par une source externe.
Les commandes et leurs fonctions A @ > ? < INPUT SCH CF SERVO REF SCH EDIT REC INH 525 625 W CTL SDI TOTAL REMAIN - dB CH 3 CH 4 TC DF UB - dB B C 30 20 16 12 8 4 0 30 20 16 12 8 4 0 30 20 16 12 8 4 0 30 20 16 12 8 4 0 CH 1 CH 2 = D Section d’affichage du compteur < Voyant TOTAL Il s’éclaire lorsque la durée de montage totale restante est affichée. D Décibelmètre = Voyant REMAIN Il s’éclaire lorsque la durée de ruban restant est affichée.
Les commandes et leurs fonctions E H IN F IN AV SP OUT OUT F G Section d’affichage du compteur E Voyants d’affichage de numéro d’événement L’appareil est capable de contrôler jusqu’à 200 jeux de données de montage (001 à 200) sous forme de numéros d’événement à 3 chiffres. L’un des affichages suivants apparaît selon l’état du montage. n###: Indique que l’événement n°### est un nouvel événement qui n’a pas été enregistré dans la liste EDL (liste de montage).
Les commandes et leurs fonctions CONTROL PREROLL SYNCHRO REMOTE 7 LOCAL 5 EXT VTR 3 1 2 CF ON OFF VTR 1 MODE REGEN R-RUN F-RUN TAPE EE 3 TC 4 5 VTR 2 REC INHIBIT MODE ON TAPE OFF EE 6 TC REGEN R-RUN F-RUN 4 REC INHIBIT 2 CH 4 CH ON OFF 5 OPERATION V2 ANALOG EDIT MODE VIDEO IN IN AUDIO OUT SDI 2 CH INT V1-V2 V1 4 CH EXT V2 ANALOG SEPARATE 6 Section des commutateurs 1 Commutateur de commande (CONTROL) REMOTE: Pour la commande de l’appareil via le connecteur REMOTE (9 contacts).
Les commandes et leurs fonctions CONTROL PREROLL SYNCHRO REMOTE 7 LOCAL 5 EXT VTR 3 CF ON OFF VTR 1 MODE TAPE EE TC REGEN R-RUN F-RUN VTR 2 REC INHIBIT MODE ON TAPE OFF EE TC REGEN R-RUN F-RUN REC INHIBIT ON OFF 2 CH 4 CH OPERATION V2 ANALOG EDIT MODE VIDEO IN IN AUDIO OUT SDI 2 CH INT V1-V2 V1 4 CH EXT V2 ANALOG SEPARATE 7 8 9 : Section des commutateurs 7 Commutateur d’entrée audio analogique (ANALOG AUDIO IN) Il permet de régler l’allocation des signaux audio aux 4 connecteurs d’e
Les commandes et leurs fonctions 1 2 CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX 3 CH 1 CH 2 CH 3 CH 4 MIX 4 3 UNI V1/V2 V1 2 MIX 1 L ASMBL 4 3 2 ANALOG MIX V 1ST EDIT VAR IN DELETE LAST X 7 DUMP LAST ED TOTAL ~ 9 DIAG 4 LIST DUR 8 SET UP 1 OUT 5 CORCT 3 LOAD T SET A4 REC CH 2 CH 3 AUTO EDIT GO TO OUT MULTI STOP REVIEW VTR 1 STILL DISP C EXIT ENTER V2 PB SDI REC REW FF VAR MIX PREVIEW STB OFF MIX 4 3 4 3 2 2 MIX 1 MIX 4 3 2 MIX 1
Les commandes et leurs fonctions CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 UNI V1/V2 MIX 4 3 3 2 2 MIX 1 L ANALOG ASMBL 4 V1 MIX V A1 A2 A3 A4 1ST EDIT CH 3 VAR IN DELETE LAST X 7 1 LAST ED TOTAL ~ 9 DIAG 4 DUMP DUR 8 SET UP LIST OUT 5 CORCT 2 3 LOAD T SET CH 2 CH 3 0 C EXIT ENTER V2 PB AUTO EDIT SDI REC GO TO OUT MULTI PLAY STILL STOP STB OFF REW FF VAR MIX PREVIEW REVIEW VTR 1 4 MIX 4 3 4 3 2 2 MIX 1 MIX 4
Les commandes et leurs fonctions CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 UNI V1/V2 MIX 4 3 3 2 2 MIX 1 V1 MIX L ANALOG ASMBL 4 1ST EDIT IN LAST X 7 DUMP ~ 9 DIAG 4 LIST DUR TOTAL 8 SET UP 1 OUT LAST ED 5 CORCT 3 LOAD T SET A4 TC REC CH 2 CH 3 0 C EXIT ENTER V2 PB SDI REC AUTO EDIT PREVIEW MULTI REVIEW VTR 1 4 PLAY STILL STOP STB OFF REW FF VAR MIX MIX 4 3 4 3 2 1 MIX 4 3 2 MIX 1 MIX 4 3 2 MIX 2 MIX MIX 1
Les commandes et leurs fonctions 12 4563 CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 MIX 4 3 UNI V1/V2 V1 2 MIX 1 L ASMBL 4 3 2 ANALOG MIX V 1ST EDIT VAR IN DELETE LAST X 7 DUMP LAST ED TOTAL ~ 9 DIAG 4 LIST DUR 8 SET UP 1 OUT 5 CORCT 3 LOAD T SET A4 REC CH 2 CH 3 AUTO EDIT GO TO OUT MULTI PREVIEW STOP REVIEW VTR 1 STILL STB OFF REW FF 7 DISP C EXIT ENTER V2 PB VAR MIX MIX 4 3 4 3 2 2 MIX 1 MIX 4 3 2 MIX 1 MIX
Les commandes et leurs fonctions 9:; CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 MIX 4 3 UNI V1/V2 V1 2 MIX 1 L ASMBL 4 3 2 ANALOG MIX V 1ST EDIT VAR IN DELETE LAST X 7 DUMP LAST ED TOTAL ~ 9 DIAG 4 LIST DUR 8 SET UP 1 OUT 5 CORCT 3 LOAD T SET BS A4 AUTO EDIT GO TO OUT MULTI SPLIT MARK IN TC REC CH 2 CH 3 STILL DISP C EXIT ENTER V2 PB SDI REC REW VAR FF MIX PREVIEW STOP STB OFF 8 MARK OUT + 1 MIX 4 3 2 MIX VTR 2
Les commandes et leurs fonctions <= > CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 MIX 4 3 UNI V1/V2 V1 2 MIX 1 L ASMBL 4 3 2 ANALOG MIX V A1 A2 A3 A4 1ST EDIT CH 3 REC VAR EVENT IN DELETE LAST X 7 DUMP LAST ED TOTAL ~ 9 DIAG 4 LIST DUR 8 SET UP 1 OUT 5 CORCT 3 LOAD T SET CH 2 CH 3 AUTO EDIT GO TO OUT MULTI STOP REVIEW VTR 1 STILL DISP C EXIT ENTER V2 PB SDI REC REW FF VAR MIX PREVIEW STB OFF MIX 4 3 4 3 2 2 MIX
Les commandes et leurs fonctions ?@AB C CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 MIX 4 3 UNI V1/V2 V1 2 MIX 1 L ASMBL 4 3 2 ANALOG MIX V 1ST EDIT VAR IN DELETE LAST X 7 DUMP LAST ED TOTAL ~ 9 DIAG 4 LIST DUR 8 SET UP 1 OUT 5 CORCT 3 LOAD T SET A4 REC CH 2 CH 3 AUTO EDIT GO TO OUT MULTI STOP REVIEW VTR 1 STILL DISP C EXIT ENTER V2 PB SDI REC REW FF VAR MIX PREVIEW STB OFF MIX 4 3 4 3 2 2 MIX 1 MIX 4 3 2 MIX 1
Les commandes et leurs fonctions F D E CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 MIX 4 3 UNI V1/V2 V1 2 MIX 1 L ASMBL 4 3 2 ANALOG MIX V A1 A2 A3 A4 1ST EDIT CH 3 REC VAR EVENT IN DELETE LAST X 7 DUMP LAST ED TOTAL ~ 9 DIAG 4 LIST DUR 8 SET UP 1 OUT 5 CORCT 3 LOAD T SET CH 2 CH 3 AUTO EDIT GO TO OUT MULTI STOP REVIEW VTR 1 STILL DISP C EXIT ENTER V2 PB SDI REC REW FF VAR MIX PREVIEW STB OFF MIX 4 3 4 3 2 2 MIX
Les commandes et leurs fonctions CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 UNI V1/V2 MIX 4 3 3 2 2 MIX 1 L ANALOG ASMBL 4 V1 MIX V A1 A2 A3 A4 1ST EDIT CH 3 VAR IN DELETE LAST X 7 DUMP LAST ED TOTAL ~ 9 DIAG 4 LIST DUR 8 SET UP 1 OUT 5 TRACK 2 3 LOAD T SET CH 2 CH 3 0 C EXIT ENTER V2 PB AUTO EDIT SDI REC GO TO OUT MULTI PLAY STILL STOP STB OFF REW FF VAR MIX PREVIEW REVIEW VTR 1 4 MIX 4 3 4 3 2 2 MIX 1 MIX 4
Les commandes et leurs fonctions 5 COARSE SC FINE SYSTEM 4 H 3 CHROMA LEVEL HUE 2 SET UP 1 VIDEO LEVEL Commandes du magnétoscope 1 (panneau latéral) Section de commande de codeur (magnétoscope 1) Les réglages du codeur et du système s’effectuent à l’aide de ces commandes pour les signaux vidéo envoyés à un appareil externe. Les commandes du magnétoscope 2 sont disposées symétriquement par rapport aux commandes du magnétoscope 1.
Les commandes et leurs fonctions 1 5 VIDEO/Y NOT USER SERVICEABLE 6 VIDEO IN PB PR 7 5 REMOTE VIDEO/Y 6 VIDEO IN PB 7 PB VIDEO MON OUT PR TC OUT VIDEO OUT V 2 PB SDI IOUT 8 A U D I O I N CH 1 CH 2 V T VIDEO R MON 1 OUT PR CH 3 (CH 1•3) CH 4 (CH 2•4) L 9 CH 2 (CH 2/4) REF IN 75Ω AUTO DC IN CH 3 (CH 1/3) CH 4 (CH 2/4) R A U D I O M O N MIC A CH 1 U (CH 1/3) D I O O U T TC IN 4 TC OUT VIDEO OUT SDI IN ACTIVE THROUGH V 1 / V 2 VIDEO/Y 3 REMOTE PR EDL V T R VIDEO/
Les commandes et leurs fonctions < VIDEO/Y NOT USER SERVICEABLE VIDEO IN PB VIDEO/Y REMOTE PR VIDEO IN PB REMOTE PR TC IN EDL V T R VIDEO/Y 2 PB VIDEO MON OUT PR VIDEO/Y TC OUT VIDEO OUT PB ACTIVE THROUGH V 1 / V 2 SDI IOUT A U D I O I N CH 1 A CH 1 U (CH 1/3) D I O O U T CH 2 PR CH 3 (CH 1•3) CH 4 (CH 2•4) L CH 3 (CH 1/3) CH 4 (CH 2/4) R MIC CH 2 (CH 2/4) REF IN 75Ω AUTO DC IN TC OUT VIDEO OUT SDI IN V 2 V T VIDEO R MON 1 OUT A U D I O M O N O U T (V2) (V1) ; Sec
Les commandes et leurs fonctions = VIDEO/Y NOT USER SERVICEABLE VIDEO IN PB PR > ? REMOTE VIDEO/Y @ VIDEO IN PB REMOTE PR TC IN EDL V T R VIDEO/Y 2 PB VIDEO MON OUT PR TC OUT VIDEO OUT V 2 PB SDI IOUT A U D I O I N CH 1 CH 2 V T VIDEO R MON 1 OUT PR VIDEO OUT CH 3 (CH 1•3) CH 4 (CH 2•4) L CH 2 (CH 2/4) 75Ω AUTO DC IN CH 3 (CH 1/3) CH 4 (CH 2/4) R A U D I O M O N MIC A CH 1 U (CH 1/3) D I O O U T REF IN TC OUT SDI IN ACTIVE THROUGH V 1 / V 2 VIDEO/Y O U T (V2) (V1
Les commandes et leurs fonctions E VIDEO IN PB VIDEO/Y NOT USER SERVICEABLE VIDEO/Y REMOTE PR VIDEO IN PB REMOTE PR TC IN EDL V T R VIDEO/Y 2 PB VIDEO MON OUT PR VIDEO/Y TC OUT VIDEO OUT PB PR ACTIVE THROUGH V 1 / V 2 SDI IOUT A U D I O I N CH 1 CH 2 CH 3 (CH 1•3) CH 4 (CH 2•4) L CH 2 (CH 2/4) 75Ω AUTO CH 3 (CH 1/3) CH 4 (CH 2/4) R A U D I O M O N MIC A CH 1 U (CH 1/3) D I O O U T REF IN TC OUT VIDEO OUT SDI IN V 2 V T VIDEO R MON 1 OUT O U T (V2) A (V1) B C D
Les commandes et leurs fonctions Section des connecteurs EF Connecteurs de sortie de contrôle sonore (AUDIO MONITOR OUT) (XLR) Ce sont les connecteurs de sortie de contrôle sonore. Il est possible de modifier leurs signaux de sortie à l’aide des commutateurs AUDIO MONITOR SELECT. Méthode de réglage Le réglage est possible si “V1+V2” a été sélectionné à la rubrique n° 772 (AUTO MONI) du menu de réglage.
Fonctionnement des menus de réglage en maintenant la touche SHIFT pressée, 4 Tout tourner la commande et régler la valeur.
Fonctionnement des menus de réglage Mémoire utilisateur et réglages usine L’appareil possède une mémoire utilisateur dans laquelle l’utilisateur pourra mémoriser ses propres réglages. Si un ensemble particulier de réglages est mémorisé, ils pourront être rappelés en même temps. Il est également possible de rappeler les réglages usine en une seule opération. (Il n’est pas possible d’enregistrer ni de rappeler les valeurs de TC PRESET et de UB PRESET.
Menus de réglage Menu SYSTEM Rubrique N° 11 Affichage en surimpression SYS SC Valeur de réglage N° 0000 0127 0255 13 VIDEO PHASE 0000 0032 0064 16 AV PHASE 0000 0090 0180 17 SYS H RANGE 0000 0001 18 30 MENU LOCK 0000 0001 70 Affichage en surimpression –127 Permet de régler la phase système. La plage variable totale est d’au moins ±180 degrés. 0 –: La phase est avancée. +: La phase est retardée. 128 –32 Permet de régler la phase du signal vidéo (par paliers de 148 ns).
Menus de réglage Menu BASIC Rubrique N° 001 Affichage en surimpression N° LOCAL ENA 0000 0001 002 TAPE TIMER 0000 0001 003 REMAIN SEL 0000 0001 008 DISPLAY SEL 0000 0001 0002 011 CHARA TYPE 0000 0001 012 SYS FORMAT 0000 0001 013 PB FORMAT 0000 0001 070 V T R 1 V T R 2 [ [ Permet de sélectionner le format d’heure affiché au compteur CTL. ±12h 0: L’heure est affichée au format de 12 heures. 24h 1: L’heure est affichée au format de 24 heures.
Menus de réglage Menu OPERATION Rubrique N° 100 Affichage en surimpression Valeur de réglage N° SEARCH ENA 0000 0001 101 102 103 SHTL MAX [ 0000 0001 0002 Permet de sélectionner la vitesse maximale d’avance accélérée et de rebobinage. x16 0: 16 fois la vitesse normale. [ x32 1: 32 fois la vitesse normale. x50 2: 50 fois la vitesse normale. [ AUDIO MUTE EE MODE SEL 0000 0001 0000 0005 0015 108 CAP. LOCK 0000 0001 109 [ [ FF.
Menus de réglage Menu OPERATION Rubrique N° Affichage en surimpression 110 MEMORY STOP N° 0000 0001 170 HUMID OPE 0000 0001 171 ALL STOP SEL 0000 0001 172 VTR1 IN SEL 0000 0001 173 174 V T R 1 V T R 2 Permet de sélectionner le traitement à effectuer lorsque le compteur affiche des zéros en mode CTL ou pendant une avance accélérée ou un rebobinage. OFF 0: Le magnétoscope n’est pas mis hors contact. ON 1: Le magnétoscope est mis hors contact automatiquement.
Menus de réglage Menu INTERFACE Rubrique N° 202 Affichage en surimpression N° ID SEL 0000 0001 205 206 207 208 BAUD RATE 0000 0001 0002 0003 0004 Permet de sélectionner l’information d’identification (ID) à envoyer en retour au contrôleur. OTHER 0: 20 25H (mode 525i) est envoyé en retour. DVCPRO 1: Le propre code d’identification du DVCPRO et F0 33H (mode [ 525i) sont envoyés en retour. Cette opération ne s’effectue pas en mode 625i.
Menus de réglage Menu EDIT Rubrique N° 303 Affichage en surimpression N° STD/NON-STD 0000 0001 0002 304 SERVO REF 0000 0001 305 306 307 V T R 1 V T R 2 Permet de sélectionner STD ou NON-STD en fonction des signaux d’entrée composites. AUTO 0: Les signaux standard/non standard sont automatiquement identifiés et traités. STD 1: Les signaux standard sont traités. (STD forcé) N-STD 2: Les signaux non standard sont traités. (NON-STD forcé) Cette opération ne s’effectue pas en mode 625i.
Menus de réglage Menu EDIT Rubrique N° 308 311 312 313 315 Affichage en surimpression Valeur de réglage N° 0000 0001 Permet de sélectionner le mode de jonction des points d’entrée de montage audio. CUT 0: Montage par coupure FADE 1: Montage par fondu [ 0000 0001 Permet de sélectionner le mode de jonction des points de sortie de montage audio.
Menus de réglage Menu EDIT Rubrique N° 370 371 Affichage en surimpression Valeur de réglage N° SYNCHRO EDL AUTO CLR SPLIT EDIT 0000 0001 376 [ ALL2 0000 0001 375 Permet de sélectionner si le montage doit être interrompu s’il n’est pas possible d’obtenir une synchronisation de phase d’une précision de ±0 image lorsque le réglage SYNCHRO est validé. OFF 0: Le montage n’est pas interrompu. ON 1: Le montage est interrompu.
Menus de réglage Menu EDIT Rubrique N° 377 378 379 380 Affichage en surimpression Valeur de réglage N° 1ST EDIT TC 1ST EDIT UB 1ST-E TITLE 1ST-E DISP 0000 0001 381 ENTRY CORR 0000 0001 382 SKIP (r) MARK 0000 0001 Description des paramètres Affichage en surimpression V T R 1 V T R 2 Permet de sélectionner la valeur de préréglage du signal de base de temps lors d’un 1er montage.
Menus de réglage Menu TAPE PROTECT Rubrique N° 400 401 Affichage en surimpression STILL TIMER N° 0000 0001 0002 0003 0004 0005 0006 0007 0008 SRC PROTECT 0000 0001 402 DRUM STDBY 0000 0001 403 V T R 1 V T R 2 [ [ [ [ Permet de sélectionner le fonctionnement du cylindre des têtes en mode annulation d’attente. [ OFF 0: Le cylindre des têtes s’arrête. ON 1: Le cylindre des têtes tourne. [ Valeur de réglage STOP PROTECT 0000 0001 Description des paramètres Affichage en surimpression 0.
Menus de réglage Menu TIME CODE Rubrique N° 500 Affichage en surimpression N° VITC BLANK 0000 0001 501 VITC POS-1 (525i mode) VITC POS-2 (525i mode) [ [ [ Permet de sélectionner le signal à régénérer lorsque le générateur de signal de base de temps (TCG) est en mode régénération. TC&UB 0: Le signal de base de temps et les bits de l’utilisateur sont [ régénérés. TC 1: Seul le signal de base de temps est régénéré. UB 2: Seuls les bits de l’utilisateur sont régénérés.
Menus de réglage Menu TIME CODE Rubrique N° 506 507 508 509 Affichage en surimpression V T R 1 V T R 2 [ [ [ [ 0000 0001 Permet de sélectionner si la correction de phase pour le signal LTC généré par le générateur de signal de base de temps doit être contrôlée. OFF 0: La correction de phase n’est pas contrôlée. ON 1: La correction de phase est contrôlée. 0000 0001 Permet de sélectionner l’indicateur du cadrage couleur dans le générateur de signal de base de temps.
Menus de réglage Menu TIME CODE Rubrique N° 571 572 Affichage en surimpression Valeur de réglage N° 0000 0001 OFF VTR1 0002 VTR2 0003 ALL 0000 0001 0002 573 574 Affichage en surimpression TC JUMP V-MON/TC OUT TC PRESET UB PRESET Description des paramètres V T R 1 Permet de sélectionner le réglage du saut du signal de base de temps. 0: Pas de saut du signal de base de temps. 1: Saut du signal de base de temps sur le côté magnétoscope 1 seulement.
Menus de réglage Menu VIDEO Rubrique N° 601 602 603 604 605 Affichage en surimpression V T R 1 V T R 2 [ [ 0000 0001 Permet de sélectionner si la phase du signal vidéo doit flotter à la position de synchronisation V des signaux vidéo pour l’aligner sur l’entrée en mode E-E ou pendant un enregistrement ou un montage. N-VF 0: La phase flotte. VF 1: La phase ne flotte pas.
Menus de réglage Menu VIDEO Rubrique N° 614 Affichage en surimpression Valeur de réglage N° Pb/Pr OUT LV 0000 0001 618 INTERPOLATE 0000 0001 622 SETUP 25 00 CMPST IN 0000 0001 01 CMPST OUT 0000 0001 02 CMPNT IN 0000 0001 03 CMPNT OUT 0000 0001 Description des paramètres Affichage en surimpression Permet de sélectionner le niveau de sortie des composantes analogiques. MII 0: Niveau MII B-CAM 1: Niveau ß-cam. En mode 625i, cette rubrique n’apparaît pas.
Menus de réglage Menu VIDEO Rubrique N° 623 Affichage en surimpression N° SETUP 50 00 CMPST IN 0000 0001 01 CMPST OUT 0000 0001 02 CMPNT IN 0000 0001 03 CMPNT OUT 0000 0001 641 WIDE IN SEL 0000 0001 0002 643 V T R 1 V T R 2 Permet de régler le traitement de configuration de 7,5% sur les signaux d’entrée et de sortie en mode 50 Mbps. (Il est possible d’afficher les réglages 00, 01, 02 et 03 du sousmenu en appuyant sur la touche STILL.
Menus de réglage Menu VIDEO Rubrique N° 670 Affichage en surimpression N° V IN SEL 0000 0001 671 V T R 1 V T R 2 Permet de sélectionner l’entrée vidéo. CMPST 0: Entrée composite analogique. CMPNT 1: Entrée à composantes analogique. Il n’est pas possible d’envoyer des signaux vidéo analogiques en mode 625i. [ [ Permet de sélectionner la sortie vidéo. CMPST 0: Sortie composite analogique. CMPNT 1: Sortie à composantes analogique.
Menus de réglage Menu AUDIO Rubrique N° Affichage en surimpression 714 EMPHASIS 726 REC CUE V T R 1 V T R 2 [ [ Permet de sélectionner les signaux d’entrée à enregistrer sur la piste repère.
Menus de réglage Menu AUDIO Rubrique N° 770 Affichage en surimpression Valeur de réglage N° CUE INSERT 0000 0001 771 AUDIO SLOW 0000 0001 0002 772 AUTO MONI 0000 0001 773 PB AUDIO SEL 0000 0001 Description des paramètres Affichage en surimpression V T R 1 Permet de sélectionner si les signaux doivent être enregistrés sur la piste repère en mode insertion audio. OFF 0: Les signaux ne sont pas enregistrés sur la piste repère, et les signaux déjà enregistrés restent sur la piste.
Menus de réglage Menu d’écran à cristaux liquides Rubrique N° B00 Affichage en surimpression N° LCD MODE 0000 0001 0002 B01 LCD HUE 0000 0030 0060 B02 LCD COLOR V T R 1 V T R 2 Permet de sélectionner les affichages de l’écran du moniteur à cristaux liquides. AUTO 0: Pendant la lecture, les affichages respectent l’information du ruban enregistré. Pendant une opération E-E (enregistrement, etc.), ils respectent [ le mode réglé aux rubriques n° 641 et n° 643 du menu de réglage.
Méthodes de fonctionnement Enregistrement des signaux d’entrée externes via le magnétoscope 1 Enregistrement des signaux d’entrée externes via le magnétoscope 2 Il est possible d’entrer et d’enregistrer les signaux à composantes analogiques et les signaux composites analogiques avec le magnétoscope 1. L’enregistrement avec le système 625i n’est pas possible.
Méthodes de fonctionnement Lecture via le magnétoscope 1, magnétoscope 2 Il est possible de lire et d’envoyer les signaux à composantes analogiques, les signaux composites analogiques, et les signaux numériques à composantes série avec le magnétoscope 1 et le magnétoscope 2. le commutateur OPERATION MODE (page le magnétoscope avec la touche 1 Placer 8 Sélectionner 13) à la position SEPARATE. VTR1 ou VTR2, et appuyer sur la touche PLAY.
Préparatifs du ruban pour le montage Avant de procéder au montage, il faudra enregistrer le signal de salve du noir, le signal de base de temps et le signal de commande sur le ruban. La méthode des préparatifs du ruban varie selon qu’il s’agit d’un montage par assemblage ou d’un montage par insertion. Préparatifs du ruban pour le montage par assemblage Pour un montage par assemblage, il faudra prévoir une période de pré-enroulement avant le premier point d’entrée du montage par assemblage.
Préparatifs du ruban pour le montage Enregistrement des titres de montage (caractères et symboles) Il est possible de surimprimer des caractères et des symboles sur les signaux vidéo (signaux de salve du noir) et de les enregistrer pendant environ 7 secondes après le début du premier montage, mais ceci n’est possible qu’en mode 525i.
Préparatifs du ruban pour le montage Préparatifs du ruban pour le montage par insertion Pour un montage par insertion, il faudra enregistrer le signal de salve du noir, le signal de base de temps et le signal de commande sur toute la durée du montage, en plus de la période de pré-enroulement du ruban de montage par assemblage.
Opérations de montage par coupure Sélection du mode de montage Montage par insertion: Montage par assemblage: sur toutes les touches correspondant aux sur la touche ASMBL. 1 Appuyer 1 Appuyer signaux à monter parmi les touches V, A1, A2, A3, Dans ce mode, les signaux audio (toutes les voies) A4 et/ou TC. et le signal de base de temps s’enregistrent simultanément. que le témoin électroluminescent de la 2 Vérifier touche ASMBL est éclairé.
Opérations de montage par coupure Enregistrement des points de montage Il y a trois façons d’enregistrer les points de montage. 1. Utilisation de la commande repérage pour repérer l’écran de montage, et réglage du point de montage avec la touche MARK IN ou MARK OUT 3.
Opérations de montage par coupure Visionnement préalable Le visionnement préalable est une répétition du montage avant de procéder véritablement au montage. Lorsque le touche PREVIEW est pressée, l’événement indiqué par le voyant d’affichage de numéro d’événement est visionné préalablement. Les images et le son produits lors de la réalisation effective du montage sont reproduits à titre de simulation sur le moniteur du magnétoscope 2, ce qui permet de les vérifier préalablement.
Opérations de montage par coupure Exécution du montage Appuyer sur la touche AUTO EDIT.
Opérations de montage décalé Avec le montage par insertion, il est possible de régler le point d’entrée audio légèrement avant le point d’entrée vidéo. (Montage décalé audio) Pareillement, il est possible de régler le point d’entrée vidéo légèrement avant le point d’entrée audio.
Montage sans réglage du point d’entrée de montage (parcage et montage) Il est possible d’effectuer le montage sans régler les points d’entrée du magnétoscope 1 et du magnétoscope 2. sur la touche AUTO EDIT pour procéder 3 Appuyer au montage. fonctionner le magnétoscope 1 et le 1 Faire magnétoscope 2, et repérer les endroits qui Pour procéder au montage en sautant le visionnement préalable, appuyer sur la touche AUTO EDIT à l’étape 2 au lieu de la touche PREVIEW, puis effectuer le montage.
Montage d’image fixe/montage de ralenti le point d’entrée et le point de sortie du le magnétoscope 1 (appareil de 1 Régler 3 Sélectionner magnétoscope 1 (appareil de lecture) à la même lecture), et tourner la commande repérage pour position. Après avoir sélectionné le magnétoscope 1 avec la touche VTR1, appuyer simultanément sur la touche MARK IN ou MARK OUT pour régler le point d’entrée et le point de sortie à la même position. faire défiler le ruban à la vitesse désirée.
Enregistrement de voix hors champ Procéder comme suit pour ajouter un son (doublage audio, enregistrement de voix hors champ) tout en regardant les images de lecture. Le son qui doit être enregistré est tout d’abord enregistré dans la mémoire, puis il est enregistré sur le ruban en procédant comme indiqué ci-dessous, ce qui permet d’effectuer l’enregistrement à l’endroit 1 2 3 4 5 6 7 précis où le son doit être ajouté.
Enregistrement de voix hors champ (1) CH 1 CH 2 CH 3 CH 4 V2 PB UNI SDI REC VAR 3 MIX 5 Sélectionner “2”. 4 MIX 4 MIX 4 MIX 3 3 3 3 2 2 2 2 MIX 1 MIX 1 MIX 1 MIX 4 1 V2 INPUT 4 < 7 Sélectionner ANALOG.
Enregistrement de voix hors champ (2) Il est également possible d’enregistrer une voix hors champ en procédant comme indiqué ci-dessous. Les étapes 1 à 7 sont les mêmes que pour l’enregistrement de voix hors champ (1). 1 2 3 4 5 6 7 8 Sélectionner “INT_VO” à la rubrique n° 317 (AUD MEM MODE) du menu de réglage. “m” s’affiche à l’écran en surimpression du magnétoscope 2. (Voir page 85.
Enchaînement de voies audio Il est possible d’effectuer un enchaînement de voies audio avec la mémoire audio interne en raccordant un mélangeur audio externe. Le son ne pourra être enregistré que sur la voie 1 et la voie 2.
Enchaînement de voies audio Procédure 2 Faire fonctionner le mélangeur audio de façon que sur la touche A1 pour éteindre son 1 Appuyer 3 les signaux de sortie du magnétoscope 1 (qui sont voyant. Le témoin électroluminescent de la touche fournis à INPUT A du mélangeur audio) soient envoyés par le connecteur MIXER CH1 OUT, et les signaux de sortie de la voie 1 du magnétoscope 2 (entrés à INPUT B du mélangeur audio) soient envoyés par le connecteur MIXER CH2 OUT. A2 reste éclairé.
Enchaînement de voies audio Etape 1 (événement 1) Point de sortie Point d’entrée Voie 1 Voie 2 Mémoire interne Environ 20 secondes Etape 2 (événement 2) Point d’entrée de voie 2 Point de sortie Voie 1 Début d’insertion de voie 1 Enchaînement de voies avec le mélangeur audio Voie 2 Section enregistrée à l’étape 1 Signaux de la mémoire interne enregistrés ici Signaux du magnétoscope 1 (appareil de lecture) enregistrés ici Mémoire interne Environ 20 secondes Vers l’étape 3 (événement 3) Pour effec
Vérification des points de montage (IN, OUT, DUR, GO TO) DUR OUT IN GO TO CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 UNI V1/V2 MIX 4 3 3 2 2 MIX 1 L ANALOG ASMBL 4 V1 MIX 1ST EDIT DELETE LAST X 7 DUMP LAST ED TOTAL ~ 9 DIAG 4 LIST DUR 8 SET UP 1 OUT 5 CORCT 3 LOAD T SET A4 TC REC CH 2 CH 3 0 C EXIT V2 PB AUTO EDIT SDI REC GO TO OUT MULTI 4 PLAY STILL STOP STB OFF REVIEW VTR 1 REW FF VAR MIX PREVIEW MIX 4 3 4 3 2 2 M
Modification et effacement des données de montage Lorsqu’un point de montage a été mal réglé, procéder comme suit pour modifier ou effacer les données de montage.
Enregistrement et rappel des données de montage L’appareil renferme une mémoire EDL (liste des décisions de montage) qui permet d’enregistrer jusqu’à 200 événements. Il est possible d’enregistrer les données de montage dans la mémoire EDL et, lorsque cela est nécessaire, de rappeler les données de l’événement désiré qui ont été enregistrées. Il est également possible de modifier les données rappelées, de monter les événements un par un, et d’effectuer un montage multi-événements.
Montage multi-événements Lorsque plusieurs événements ont été enregistrés, il est possible de les monter en même temps. le premier des événements à monter. 1 Rappeler (Voir la section relative à l’enregistrement et au rappel des données de montage.) sur la touche MULTI ([SHIFT] + [AUTO 2 Appuyer EDIT]). Les données sont automatiquement montées depuis l’événement rappelé jusqu’au dernier événement.
LAST X/LAST ED/TOTAL LAST X ([SHIFT]+[IN]) LAST ED ([SHIFT]+[OUT]) TOTAL ([SHIFT]+[DUR]) CH 1 POWER OFF AUDIO MONITOR SELECT ON MIX CH 1 CH 2 CH 3 CH 4 MIX 4 3 UNI V1/V2 V1 2 MIX 1 L ASMBL 4 3 2 ANALOG MIX 1ST EDIT VAR IN DELETE LAST X 7 DUMP LAST ED TOTAL ~ 9 DIAG 4 LIST DUR 8 SET UP 1 OUT 5 CORCT 3 LOAD T SET A2 A3 A4 REC CH 2 CH 3 AUTO EDIT GO TO OUT MULTI STOP REVIEW VTR 1 STILL DISP C EXIT V2 PB SDI REC REW FF VAR MIX PREVIEW STB OFF MI
Réglage du signal de base de temps (T SET) Cette procédure est suivie du réglage de la valeur initiale du signal de base de temps pour l’enregistrement manuel ou pour un premier montage.
Réglage du signal de base de temps Pour effectuer un premier montage (1ST EDIT) en réglant la valeur initiale du signal de base de temps (T SET) le curseur sur la rubrique n° 377 (1ST EDIT 1 Aligner TC) du menu de réglage. Pour enregistrer un signal de base de temps dont la valeur initiale a été réglée pendant un montage par assemblage ou un montage par insertion du signal de base de temps (magnétoscope 2 seulement) 2 Appuyer sur la touche T SET ([SHIFT] + [3]).
Réglage du signal de base de temps Pour effectuer un montage par assemblage ou un montage par insertion du signal de base de temps en préréglant les bits de l’utilisateur Aligner le curseur sur la rubrique n° 574 (UB 1 PRESET) du menu de réglage. 2 Appuyer sur la touche T SET ([SHIFT] + [3]). les touches numériques pour entrer la 3 Utiliser valeur des bits de l’utilisateur. 4 Appuyer sur la touche ENTER. “SW” à la rubrique n° 504 (REGEN 5 Sélectionner MODE) du menu de réglage.
CORCT/TRACK/DISP Fonction correction (CORCT) Fonction suivi (TRACK) Cette fonction permet de corriger les données de montage d’un événement existant (dont les données de montage sont déjà enregistrées dans la mémoire), mais pas d’un nouvel événement. Cette fonction permet de régler les points de montage du magnétoscope 1 (appareil de lecture) en réponse à une modification du point d’entrée du magnétoscope 2 (appareil d’enregistrement). sur la touche CORCT ([SHIFT] + [5]).
Effacement des données de montage de la mémoire EDL Effacement de la totalité des données de montage 1 Appuyer sur la touche EVENT. trois fois sur la touche 9 pour afficher 2 Appuyer “999” sur les voyants d’affichage du numéro d’événement. sur la touche ENTER tout en maintenant 3 Appuyer la touche SHIFT pressée. Toutes les données de montage de la mémoire EDL sont effacées.
Réglages du codeur Lorsque les raccordements système sont terminés, il faut régler les signaux vidéo (ENCODER OUT) avant d’envoyer tout autre signal pour pouvoir obtenir un montage précis et sans erreur. (Il faudra peut-être répéter ce réglage chaque fois qu’un câble de raccordement est remplacé ou que les raccordements sont modifiés.) Pour régler le codeur sur le portable: 1 Raccorder dessous.
Réglages du codeur les commandes SYSTEM PHASE. le commutateur REMOTE/LOCAL à la 2 Placer 4 Régler 1 Lire les barres de couleur standard sur le position (LOCAL) à laquelle le réglage doit être effectué. les réglages à l’aide d’un appareil source 3 Effectuer discret. Toute déviation du niveau de configuration, du niveau vidéo, du niveau des couleurs et de la teinte provoquera un décalage des couleurs sur l’appareil d’enregistrement. Les régler à l’aide d’un appareil source discret.
Envoi (DUMP) et chargement (LOAD) des données de montage à un appareil externe Il est possible d’envoyer les données de montage enregistrées dans la mémoire EDL à un appareil externe via le connecteur EDL du panneau arrière. L’envoi des données (à un ordinateur par exemple) et le chargement des données d’un ordinateur permettent d’utiliser et de gérer un grand choix de systèmes des différentes façons suivantes.
Envoi (DUMP) et chargement (LOAD) des données de montage à un appareil externe Envoi des données d’un appareil externe Réglage de l’appareil externe et méthodes de communication les paramètres de communication et le 1 Régler format des données à recevoir sur le menu INTERFACE. sur la touche LOAD ([SHIFT] + [2]). 2 Appuyer Le témoin électroluminescent de la touche VTR1 clignote pour indiquer que le mode réception des données est validé.
Envoi (DUMP) et chargement (LOAD) des données de montage à un appareil externe A propos du format EDL Il est possible de sélectionner le format AG-A850 ou le format CMX340 pour le format des données lorsque les données de montage sont envoyées à un ordinateur personnel ou un autre appareil externe. Sélectionner le format à la rubrique n° 271 (EDL FORMAT) du menu de réglage.
Envoi (DUMP) et chargement (LOAD) des données de montage à un appareil externe $ Format CMX340 O Certaines des données sont converties à ce format, de sorte qu’elles ne seront pas complètement restaurées lors d’un nouveau chargement. Numéro d’événement: Les numéros d’événement supprimés sont mis en paquets et envoyés. Pendant la réception, les numéros d’événement sont ignorés, et 200 événements maximum sont reçus en séquence à partir du premier événement.
Affichages en surimpression Il est possible de surimprimer des caractères et des symboles sur les signaux de sortie du moniteur à cristaux liquides de l’appareil ou au connecteur VIDEO MONITOR OUT. Cette fonction surimpression se valide et s’invalide en appuyant sur la touche DISP ([SHIFT] + [0]). Les informations à surimprimer et à afficher se sélectionnent à la rubrique n° 002 (DISPLAY SEL) du menu de réglage. Informations affichées à la ligne STATUS (mode de fonctionnement du magnétoscope) o m SHTL +32.
Messages d’erreur L’un des messages d’erreur suivants s’affiche quand une anomalie se produit dans l’appareil. Le magnétoscope passe en mode arrêt automatique, ou le contact se coupe de force. Si l’erreur est toujours affichée lorsque l’appareil est mis hors contact puis de nouveau sous contact, contacter son détaillant. Registre d Affichage en surimpression DEW “d” et les valeurs du compteur Mode du s’affichent magnétoscope alternativement. Description Il s’est formé de la condensation (buée).
Messages d’erreur Registre Affichage en surimpression Description Opération du magnétoscope E — 53 WINDUP ERROR S’affiche lorsque le temps de ruban total a été détecté alors que la quantité entraînée par la bobine réceptrice et la quantité avancée par la bobine débitrice sont anormales. Arrêt automatique E — 55 UNLOAD ERROR S’affiche lorsque le ruban n’est pas entraîné pendant le déchargement.
Nettoyage des têtes vidéo L’appareil possède une fonction de nettoyage automatique des têtes vidéo qui réduit automatiquement la saleté sur les têtes. Cependant, pour accroître encore davantage la fiabilité de l’appareil, il est recommandé de nettoyer les têtes vidéo chaque fois que cela s’avère nécessaire. Pour les détails sur la façon de nettoyer les têtes vidéo, consulter l’un de nos services aprèsvente ou son détaillant.
Données techniques [Données générales] [VIDEO] Tension d’alimentation: 12 V c.c. Courant d’entrée: 12 A $ Vidéo numérique (pareil pour le magnétoscope 1 et le magnétoscope 2) Fréquences d’échantillonnage: O DVCPRO 50 Y: 13,5 MHz 6,75 MHz PB/PR: O DVCPRO Y: 13,5 MHz PB/PR: 3,375 MHz Quantizing: 8 bits Système de compression vidéo: DCT + code à longueur variable Taux de compression: O DVCPRO 50: 1/3.
Données techniques [VIDEO] [AUDIO] $ Entrée à composantes analogique/sortie à composantes analogique (pareil pour le magnétoscope 1 et $ Audio numérique (pareil pour le magnétoscope 1 et le magnétoscope 2) Fréquence d’échantillonnage: 48 kHz Quantification: 16 bits Réponse en fréquence: 20 Hz à 20 kHz ±1 dB (niveau référence) Plage dynamique: Plus de 85 dB (1 kHz, accentuation invalidée, pondérée “A”) Distorsion: Moins de 0,1% (1 kHz, accentuation invalidée, niveau référence) Diaphonie: Moins de –80 db (
Données techniques [CONNECTEURS ENTREE/SORTIE] $ VIDEO $ AUDIO Entrée à composantes analogique: BNC a6 ([Y/PB/PR] a2) (magnétoscope 1, magnétoscope 2) Y: 1,0 V [c-c], 75 Ω, commuté avec l’entrée composite analogique PB/PR: 0,525/0,757 V [c-c] réglable, 75 Ω (barres de couleur 75%, configuration 0%) Entrée composite analogique: BNC a2 (magnétoscope 1, magnétoscope 2), 1,0 V [c-c], 75 Ω, commuté avec l’entrée Y à composantes analogique Entrée référence: BNC a2 (raccordé en dérivation), 75 Ω, commutation mar
Données techniques [Moniteur à cristaux liquides] Panneau à cristaux liquides: Matrice active TFT, grand écran, 7 pouces a2 (magnétoscope 1, magnétoscope 2), grand écran/écran normal réglable (bords vides en mode normal), 525i/625i réglable Réglage de luminosité: Commandes a2 (magnétoscope 1, magnétoscope 2) Réglage de qualité des images: Couleur, teinte (menus affichés à l’écran séparés pour la gauche et la droite) (Teinte: mode 525i seulement) Sélection de rétroéclairage: Clair, sombre, éteint (commutateu
Panasonic Canada Inc.