Panasonic Broadcast AJ-HD1700 Menu Information
System menus Video output signal adjustments No./Item 00 WFM SEL 05 ENCODER SEL 06 V LEVEL CTRL Description of setting This enables one of a number of different signals to be output from the VIDEO OUT 2 output connector. 0000 CTL: The CTL signal is output. 0001 TC: The time code signal is output. 0002 VIDEO: The video output signal is output. 0003 RF_L: The PB L RF signal is output. 0004 RF_R: The PB R RF signal is output. 0005 ENV_L: The PB L ENV signal is output.
System menus No./Item 12 SYS H (HD)*UP No./Item Description of setting For adjusting the system phase of the HD SDI output. When the SHIFT button is pressed, the display transfers to the submenu screen; press the SHIFT button again to return the display from the submenu screen. 15 VO SYS H (SD)*DW Description of setting For adjusting the system phase of the VIDEO OUT.
System menus No./Item 18 SCH (SD)*DW Description of setting No./Item For adjusting the SCH phase. When the SHIFT button is pressed, the display transfers to the submenu screen; press the SHIFT button again to return the display from the submenu screen. Submenu screen 00 COARSE 01 FINE 20 AV PHASE 25 SYSTEM FREQ* For adjusting the SCH phase in 90o steps (The SC phase changes, and the H phase remains unchanged.
Setup menus No./Item 000 P-ROLL TIME Description of setting For setting the preroll time. Any time from 0 to 30 seconds can be set in 1second increments. 0000 0s : : 0005 5s : : 0030 30s • During automatic editing (PREVIEW or AUTO EDIT), no operations are performed if the preroll time is set to 0 seconds. • If the phases are to be synchronized between two decks for editing as per the setup menu item No.004 (SYNCHRONIZE) setting, set the preroll time to at least 2 seconds.
Setup menus (continued) No./Item 006 DISPLAY SEL 007 CHARA H-POS Description of setting • The following mode displays appear depending on the format used. DVCPRO HD-LP > DVCPRO_HD-LP > DVCPRO HD DVCPRO_HD > DVCPRO50 DVCPRO_50 > DVCPRO DVCPRO > DV DV > DVCAM DVCAM • When setting 2 (T&S&M) is selected, an error message appears if a warning or error has occurred. • REC TIME and REC DATE are displayed only during DV or DVCAM format playback.
Setup menus (continued) Formats in which the tape is played back No./Item 022 PB FORMAT 023 FORMAT SEL 030*3 HD FREQUENCY 031*4 OUT REF Description of setting For selecting the format in which the tape is to be played back. 0000 MANU: The format is determined by the setting selected for setup menu item No.023 (FORMAT SEL). 0001 AUTO: The tape is played back in the format in which it was recorded. For selecting the format when “MANUAL” has been selected as the setup menu item No.
Setup menus No./Item 100 SEARCH ENA 101 SHTL MAX Description of setting For selecting the direct search dial operation. 0000 DIAL: Direct search dial operations are performed. 0001 KEY: Operation does not transfer to the search mode unless the SHTL, JOG or VAR button is pressed. For selecting the maximum speed of shuttle operations. k9.8: k9.
Setup menus (continued) No./Item Description of setting 112 For selecting what playback images are to be output in the STANDBY OFF mode and EJECT mode. 0000 DIS: The video output is muted. 0001 STB OFF: Only when the STANDBY OFF mode is established is the image which was being played back at that moment frozen and output. 0002 SOF&EJ: When either the STANDBY OFF mode or the EJECT mode is established, the image which was being played back at that moment is frozen and output. FRZ MODE SEL No.
Setup menus (continued) No./Item 116 EJECT LAMP 118*1 SP MODE INH Description of setting For selecting whether the EJECT lamp is to remain lighted or go off after the cassette tape has been ejected. 0000 MODE1: The EJECT lamp remains lighted. 0001 MODE2: The EJECT lamp goes off. PAGE MODE 132 ROTA MODE 133 KEY BEEP 134 ALARM BEEP For selecting what cue point operation is to be performed when the multi cue function has been set to ON.
Setup menus No./Item 200 PARA RUN Description of setting For selecting whether to operate two or more VTRs in synchronization. 0000 DIS: The VTRs are not operated in synchronization. 0001 ENA: The VTRs are operated in synchronization. To operate the VTRs in synchronization, set all the VTRs to 1 (ENA). (Refer to pages 14 and 19.) 202 ID SEL For setting what ID information is to be returned to the controller. 0000 OTHER 0001 DVCPRO 0002 ORIG No.
Setup menus No./Item 300 IN/OUT DEL 301 NEGA FLASH 302 CONFI EDIT Description of setting For selecting the operation to be performed when an edit point has been set incorrectly (when the OUT point comes before the IN point). 0000 MANU: Editing is not performed unless the illegal edit point is cleared or set properly. 0001 AUTO: The edit point which had already been input is cleared automatically.
Setup menus (continued) No./Item 320*1 EDIT RPLCE1 321*1 EDIT RPLCE2 322*1 EDIT RPLCE3 Description of setting For setting the allocation of the channels for the analog audio presets of a controller when a controller without a function to control the edit presets of the digital audio signals is used to edit the digital audio signals of the VTR. The VTR’s CH1 edit presets are set to ON or OFF following the analog audio signals specified by the controller. 0000 N-DEF: Not set.
Setup menus No./Item 400 STILL TIMER 401 SRC PROTECT Description of setting For selecting the duration of the time taken after the VTR is left standing in the STOP or search STILL mode (JOG, VAR or SHTL) before the tape protection mode is established. (Units: s = seconds, min = minutes) 0000 0.5s 0001 5s 0002 10s 0003 20s 0004 30s 0005 40s When a DV or DVCAM tape is 0006 50s used, the time is set to 10 0007 1min seconds even when a setting of 0008 2min 2 (10s) or longer is selected.
Setup menus
Setup menus
Setup menus
Setup menus
Setup menus
Setup menus
Setup menus
Setup menus
Setup menus
Setup menus
Setup menus
Setup menus
Setup menus (continued) No./Item Description of setting No./Item 763 For selecting the scale display of the audio level meter. METER 0000 PEAK_0: SCALE [The audio level is displayed with 0 dB as the (This menu is maximum level. not displayed for 0001 REF_0: AJ-HD1700E.) The audio level is displayed with 0 dB as the reference level. 791 CUE PB VOL Description of setting For adjusting the playback level of the CUE audio signal.
Setup menus
Setup menus Follow the steps below to switch the system frequency (59/60 Hz, 50 Hz, 23/24 Hz, 25 Hz (HD) or 25 Hz(SD)). the procedure for the (page 60) to change the C system menu item No.25 (SYSTEM FREQ) setting.
Setup menus
Setup menus Setup menus No. Menu item System menu No.
Setup menus Setup menus No. Menu item System menu No.
Setup menus Setup menus No. Menu item System menu No.
Setup menus Setup menus No. Menu item System menu No.