080I Multi-purpose Digital Camera AK-HC910P Before attempting to connect, operate or adjust this product, please read these instructions completely.
For Your Safety FCC Note: This device complies with Part 15 of the FCC Rules. To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.
CONTENTS For Your Safety...................................2 Preface ...............................................4 Features..............................................4 Precautions.........................................5 Major Operating Controls and Their Functions .............................6, 7 How to Install ......................................8 _ How to set the lens .......................8 _ How to install on the camera housing, pan/tilt head, tripod, etc. ...................................
Thank you very much for purchasing the multi-purpose digital camera. Preface This camera employs new 2/3q 2.2 million-pixel FIT CCD [1920(H)k1080(V)], realizing a compact light-weight system including the optical system. Also, the newly developed CCD having an FIT configuration suited for higher picture quality and the development of low-noise, high-speed amplifiers have enabled the realization of high sensitivity, high S/N ratio, and wide dynamic range.
Precautions DON’TS DO’S • Refer any servicing to qualified service personnel. • Do not attempt to disassemble the camera or other units. In order to prevent electric shock, do not remove screws or covers. There are no user-serviceable parts inside. • Handle the camera with care. • Protect the precision made lens by placing the lens cap over when the camera is not in use. If the lens is not installed, protect the surface of the prism by placing the body cap into the lens mount hole.
Major Operating Controls and Their Functions _ Front Panel 3 4 1 2 1 Lens Mount 2/3q standard bayonet type (B4 mount) lens is installed. 2 Lens Fixing Ring Knob Lens is fixed by turning the knob counterclockwise. 3 Cable Clamp Used to clamp the lens cable. 4 Lens Connector [LENS] Used to connect the camera cables of the lens. Pin No. 9 8 1 2 10 7 12 6 3 11 5 4 Signal Pin No.
Major Operating Controls and Their Functions 6 Camera mounting hole (1/4-20UNC) 7 Camera mounting hole (3/8-16UNC) The screw holes can be used to secure the camera for installing it on camera housing, and when using a pan/tilt head or a tripod. _ Side Panel 8 9 BREAKER ZOOM/ FOCUS 1 : SDI OUT 2 ; 1/ F 8 Breaker [BREAKER] If the breaker is operated due to over-current or the like, check the cause and eliminate the trouble, then press the breaker button.
How to Install Be sure to ask the dealer for the installation, adjustment and connection of this equipment. _ How to set the lens • Standard 2/3q bayonet type (B4 mount) lens of any makers can be used*. 1 Turn the lens fixing ring knob counterclockwise to remove the lens mount cap. 2 Set the lens in place, and turn the lens fixing ring knob clockwise to precisely fix the lens. 3 Connect the lens cable to the lens connector.
How to Set Up the System (Connection) _ Connection of remote control box • Use multi-cable for the connection of HD controller AK-HRP900 and this unit. BREAKER Coaxial Cable HD-SDI (5C-FB) ZOOM/ FOCUS 1 SDI OUT 2 D-sub 15-pin HD Monitor 1/ F AK-HC910P Video Input Signal Multi-cable (5m) AK-HDMLTCA05 HD Monitor YPbPr O I AC Adaptor AW-PS505 NOTE Note that the monitor output is attenuated and deteriorated if the cable is too long.
Multi-purpose Digital Camera Control System Configuration 1 Remote (zoom/focus control) cable BREAKER HD-SDI ZOOM/ FOCUS Coaxial Cable (5C-FB) 1 SDI OUT 2 1/ F Remote controllable lens D-sub 15-pin Multi-purpose Digital Camera AK-HC910P Multi-cable (5m) AK-HDMLTCA05 HD Monitor O I AC Adaptor AW-PS505 External sync signal (3 value sync) DC Power Cable D-sub 15-pin HD Controller AK-HRP900 10
Multi-purpose Digital Camera Pan/Tilt Head Compatible System Configuration 1 Remote controllable lens Coaxial Cable (5C-FB) HD-SDI BREAKER ZOOM/ FOCUS 1 SDI OUT 2 1/ F Remote (zoom/focus control) cable Multi-cable (5m) AK-HDMLTCA05 Multi-purpose Digital Camera AK-HC910P O I AC Adaptor AW-PS300 ND/EXT SDI IN LENSE I/F CAMERA I/F 1394 G/L I N CONTROL IN IP/RP Pb OUT DC Power Cable HD Monitor DC12V IN C S OP Pr /SDI OUT Y/VIDEO OUT Pan/Tilt Head AW-PH300A O I AC Adaptor AW-PS505 External
Multi-purpose Digital Camera Control System Configuration 2 (System for remotely monitoring picture control) Remote (zoom/focus control) cable Multi-cable (5m) AK-HDMLTCA05 BREAKER HD-SDI ZOOM/ FOCUS Coaxial Cable (5C-FB) 1 SDI OUT 2 1/ F Remote controllable lens Relay box AK-HTF900 Multi-purpose Digital Camera AK-HC910P Transfer DC Power Cable O I AC Adaptor AW-PS505 Multi-cable (5m) AK-HDMLTCA05 HD Monitor O I AC Adaptor AW-PS505 DC Power Cable HD Controller AK-HRP900 12
Multi-purpose Digital Camera Pan/Tilt Head Compatible System Configuration 2 (System for remotely monitoring picture control) Remote controllable lens Multi-cable (5m) AK-HDMLTCA05 BREAKER HD-SDI ZOOM/ FOCUS Coaxial Cable (5C-FB) 1 SDI OUT Relay box AK-HTF900 2 1/ F Multi-purpose Digital Camera AK-HC910P Remote (zoom/focus control) cable Transfer O I AC Adaptor AW-PS505 ND/EXT SDI IN Multi-cable (5m) AK-HDMLTCA05 LENSE I/F CAMERA I/F 1394 G/L I N CONTROL IN IP/RP Pb OUT HD Monitor DC12V
Operation Procedure 1 Turn on the power of each 5 Adjust the black balance. equipment. 2 Properly adjust the light for the • This adjustment is needed when the camera is used for the first time or after leaving unused for a long time. 3 Adjust the flange back of the lens, • The adjustment is necessary when the ambient temperature is greatly changed or at the change of season. object. the iris and the focus.
How to Adjust _ Flange back adjustment (for zoom lens) The adjustment is to adjust the focus in all the range from the maximum zoom to the widest angle of the zoom lens. 1 Shoot a dark object to open the iris. 2 Adjust the distance from the object to 6.6 ft. (2 m) at least, then loosen the flange back fixing knob of the lens. 3 Set the lens to the maximum zoom and adjust the focus by turning the focus ring. 4 Set the lens to the widest angle and adjust the focus by turning the flange back adjust ring.
How to Adjust _ White balance adjustment Adjust the white balance after shooting a white object by at least 50% of the screen. NOTE: If the white signal level is over 100% or less than 50%, the white balance may not be normally adjusted. _ Color temperature and while balance adjustment (reference) When carbon is burnt, it develops 10000K Blue sky various colors of light depending on the temperature.
How to Adjust _ Black balance adjustment • Adjust it with the lens closed. When the motor drive lens is controlled from the camera, adjusting the black balance causes the lens to be automatically closed. _ Gen lock adjustment When multiple cameras are used or the camera is combined with other equipment, it is necessary to adjust the phase for phase matching by external synchronization.
Setting of Menu Items _ Configuration of menu display screen USER MENU 1.MAINTENANCE 2.SETTING 3.CAM ID 4.FILE MENU Maintenance menu ° MAINTENANCE ° 1.BLACK SHADING 2.PED,GAMMA,FLARE 3.KNEE,WHITE CLIP 4.R/B GAIN 5.DTL 6.GAIN,AUTO IRIS 7.S.GAIN 1 8.S.GAIN 2 9.S.GAIN 3 10.MATRIX 11.COLOR CORRECTION1 12.COLOR CORRECTION2 USER MENU Using condition setting menu °° SETTING°° 1.MODE 2.SHUTTER 3.H.
Setting of Menu Items _ USER menu (Initial screen) The readout data at start of power supply is the data just before cutting off the power supply, and the operation is started with the data. USER MENU 1.MAINTENANCE 2.SETTING 3.CAM ID 4.FILE MENU 1. MAINTENANCE It sets various adjusting data. 2. SETTING It sets various modes. 3. CAM ID It sets the camera ID. 4. FILE MENU It executes file loading and saving, and makes the basic setting of data display.
Setting of Menu Items ! Maintenance menu • Move the cursor (arrow mark) to the item to be adjusted and press the MENU key, then it enters the adjustment menu thereunder. °MAINTENANCE° 1.BLACK SHADING 2.PED,GAMMA,FLARE 3.KNEE,WHITE CLIP 4.R/B GAIN 5.DTL 6.GAIN,AUTO IRIS 7.S.GAIN 1 8.S.GAIN 2 9.S.GAIN 3 10.MATRIX 11.COLOR CORRECTION1 12.COLOR CORRECTION2 • Move the cursor to MAINTENANCE and press the MENU key, then it returns to USER MENU.
Setting of Menu Items ! Maintenance menu 2 Pedestal, gamma, flare adjustment menu °° PED,GAMMA,FLARE°° M PED R PED B PED M GAMMA R GAMMA B GAMMA R FLARE G FLARE B FLARE GAMMA FLARE :+027 :+000 :+000 :0.45 :+00 :+00 :010 :000 :017 :ON :ON M PED: Master pedestal can be adjusted only by turning the control panel VR. The R, G, B pedestal can be totally adjusted. R, B PED: R, B pedestal adjustment. Besides the master pedestal adjustment, R, B pedestal can be independently adjusted.
Setting of Menu Items ! Maintenance menu °° KNEE,WHITE CLIP M KNEE POINT R KNEE POINT B KNEE POINT M KNEE SLOPE R KNEE SLOPE B KNEE SLOPE A.KNEE POINT A.KNEE LVL WHITE CLIP LVL KNEE WHITE CLIP 3 Knee&white clip adjustment menu °° M KNEE POINT: Master knee point adjustment. G, B, R knee point can be totally adjusted. :95.00% :+00.00% :+00.00% :95.00% :+000 :+000 :95.00% :108 :109% :MANU :ON R, B KNEE POINT: R, B knee point adjustment.
Setting of Menu Items ! Maintenance menu °° R/B GAIN 4 Gain adjustment menu °° R GAIN B GAIN The gain of R, B GAIN is adjusted. The difference from the state of being white-balanced can be adjusted. :+000 :+000 • The numeral value displayed after normal ending of AWB is “0” for both of R, B. 5 Detail adjustment menu °° DTL °° DTL TOTAL DTL LVL H DTL LVL CRISP LVL DEPENDENT PEEK FREQUENCY KNEE APERTURE KNEE APA.
Setting of Menu Items ! Maintenance menu 5 Detail adjustment menu (continued from previous page) °° DTL °° DTL TOTAL DTL LVL H DTL LVL CRISP LVL DEPENDENT PEEK FREQUENCY KNEE APERTURE KNEE APA.LVL SLIM DTL DTL(+) DTL(-) DTL CLIP DTL SOURCE °° GAIN,AUTO IRIS :ON :+00 :11 :02 :2 :10 :ON :10 :OFF :+00 :+00 :0 :(B+G)/2 DTL (+): Setting of DTL at the edge in positive direction. DTL (–): Setting of DTL at the edge in negative direction. DTL CLIP: Setting of clip level of DTL edge.
Setting of Menu Items ! Maintenance menu °° S GAIN 1°° GAIN ° TOTAL ANLG GAIN PIX MIX H DTL LVL CRISP LEVEL DEPENDENT PEAK FREQUENCY M GAMMA MASTER PED OFFSET R PED OFFSET B PED OFFSET 7 Super gain, Detail, Pedestal-offset level setting menu TOTAL GAIN: Total gain in analog, pixel addition, and memory addition is displayed. ANLG GAIN: Gain setting in analog. PIX MIX: Gain setting in horizontal pixel addition. Capable of setting 0/6 dB. H DTL LVL: DTL level setting of super gain.
Setting of Menu Items ! Maintenance menu 8 Matrix menu Selection of table A, B or OFF. Adjustment of gain of each color. < MATRIX > MATRIX MATRIX MATRIX MATRIX MATRIX MATRIX MATRIX TABLE R-G R-B G-R G-B B-R B-G :A :+00 :+00 :+00 :+00 :+00 :+00 9 Color correction 1 menu < COLOR CORRECTION1 > SAT PHASE R +00 +00 Mg +00 +00 B +00 +00 Cy +00 +00 G +00 +00 Y1 +00 +00 Adjustment of gain (saturation) and phase of each color.
Setting of Menu Items @ Setting menu - Menu for various settings. °° SETTING°° 1.MODE 2.SHUTTER 3.H.PHASE 1 Camera mode setting menu °° MODE°° BLACK STRETCH D5600K CABLE COMPE SUP GAIN CAM ID CAM ID POSI MATRIX TABLE COLOR CORRECTION STATUS BLACK STRETCH: Setting of the function of expanding low-brightness analog video level. It is set by ON/OFF.
Setting of Menu Items @ Setting menu 1 Camera mode setting menu (continued from previous page) °° MODE°° BLACK STRETCH D5600K CABLE COMPE SUP GAIN CAM ID CAM ID POSI MATRIX TABLE COLOR CORRECTION STATUS :OFF :OFF :0m :OFF :BAR :0 :OFF :OFF :ON CAM ID POSI: It sets the display position of camera ID. 0: top left, 1: top right, 2: down left, 3: down right. MATRIX TABLE: It sets A, B or OFF of Matrix table. COLOR CORRECTION: Setting of matrix ON/OFF.
Setting of Menu Items # Camera ID setting menu °°CAM ID °° ID:AKHC900 $ File managing and renewing menu - File operation menu H FILE MENU ° ° FILE SAVE FILE? SAVE : blinking display. :USER1 :USER1 : 1 The file selected by FILE is loaded. It can be selected from [PRESET/USER1 / USER2 /CURRENT]. When desired to return to the previous data after loading other file, select “CURRENT”.
Setting of Menu Items $ File managing and renewing menu - File operation menu (continued from previous page) H FILE MENU ° FILE SAVE FILE? SAVE :USER1 :USER1 : 2 When saving the current data, two files (USER1 /USER2) can be saved. Select the file by “SAVE FILE?” Select “USER1” and move the cursor to SAVE and press the MENU key, then the item menu is displayed. 3 SAVE IN USER1. OK? “YES” and “NO” are displayed. Move the cursor from “NO” to “YES” and check that “YES” blinks.
Outside Dimension Diagram 7/16q (10) LENS ( ): mm BREAKER 4-15/16q (125) ZOOM/ FOCUS 1 SDI OUT 2 1/2q (12) 1/ F 6-5/16q (160) 4-3/8q (110) 5/8q (15) 13/16q (20) 31
Specifications & Accessories _ Specifications Supply voltage: DC 12V (supplied from D-SUB 15 pins) Power consumption: 22 W 1 indicates safety information. Image pickup device: System: Resolving optical system: Optical filter: 2/3q 2.2 million-pixel FIT CCDk3 GBR image pickup system F1.4 prism CC: clear, 4300K, 6300K, cross ND: 100%, 25%, 6.3%, 3.2% Lens mount: Bayonet type Output spec.: SMPTE 292M Sensitivity: F10, 2000Ix, 3200K, white reflection rate 89.
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY UNIT COMPANY OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Executive Office: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000 EASTERN ZONE: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621 Southeast Region: 1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835 Central Region: 1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200 WESTERN ZONE: 3330 Cahuenga Blvd W.