User Guide
Table Of Contents
- Operating Instructions
- Read this first! (For AW-HE20KP, AW-HE20WP)
- Getting Started
- Characteristics
- Accessories
- Operating Precautions
- Parts and Functions
- Wireless Remote Control (optional accessory)
- Network Settings
- Basic Shooting Operation
- 1. Make sure the subject brightness is in the appropriate level.
- 2. Make sure the unit and all devices are well connected and power on.
- 3. Press one of the [CAMERA 1] to [CAMERA 4] buttons on the wireless remote control to select the unit if using the wireless remote control. Even when using only one unit, it must still be selected from the wireless remote control or controller.
- 4. Select the scene (shooting) mode.
- 5. Start shooting.
- Power on and Power Off the Camera Unit
- Power on the Camera Unit
- Power off the Camera Unit
- 1. Press one of the [CAMERA 1] to [CAMERA 4] buttons on the wireless remote control to select the unit.
- 2. Press the [ON/STANDBY] button on the wireless remote control for 2 seconds.
- The unit enters STANDBY mode.
- 3. The unit’s status display lamp now lights up orange.
- 4. If a multiple number of units are used, repeat steps 1 and 2 as required.
- 5. Set all the power switches of the units and devices connected in the system to OFF.
- Priority Mode
- Selecting the Scene Mode
- Operating the Camera unit
- Control the Picture’s Direction (using the wireless remote control)
- Zoom In/Out Function (using the wireless remote control)
- Switching the Direction or Zoom Speed (using the wireless remote control)
- Control the Picture’s Direction (using the controller)
- Zoom In/Out Function (using the controller)
- Switching the Direction or Zoom Speed (using the controller)
- What to do when Encountering Problems in the Basic Shooting Operations
- Advanced Operations
- Menu Operation
- Operations Table
- When performing the operations using the wireless remote control
- 1. Press the [CAMERA 1], [CAMERA 2], [CAMERA 3] or [CAMERA 4] button to select the unit which is to be operated.
- 2. Press the [MENU] button for 2 seconds.
- 3. Press the [▲] or [▼] button to bring the cursor to the item to be selected.
- 4. Press the [] button.
- 5. Press the [▲] or [▼] button to bring the cursor to the item to be set.
- 6. Press the [] button.
- 7. Press the [▲] or [▼] button to change the setting.
- 8. Press the [] button.
- 9. After the setting has been completed, press the [MENU] button for 2 seconds.
- Menu Items
- Menu Table
- Web Screen Start-up
- Web Live Screen Operation
- Troubleshooting
- Specification
- Index
21
Parts and Functions
1 2 3
4
1. Lens
2. Tally status indicator
- Red light: The unit is receiving tally command.
- Red light flashing once (1Hz): The unit’s pan/tilt limit
is being configured.
- Red light flashing twice (1Hz): The unit’s pan/tilt limit
is being cancelled.
- Blue light: USB Video Class/Audio Class is in
operation.
3. Camera head
4. Power status indicator
- Orange light: Standby mode
- Green light: The unit is turned on
- Flashing green light (1Hz): The unit is receiving a
wireless remote control signal with a matching
remote control ID
- Flashing(1Hz) orange light: The unit is receiving a
wireless remote control signal with a different
remote control ID
- Flashing (5Hz) green light: After Initialization 1 and
Initialization 2 via DipSW
- High speed (5Hz) flashing orange light: When a
signal from the wireless remote
control is received while the wireless control is set to
“Disable” from the web screen menu.
- Flash (1Hz) red light: Firmware updating
- Red light: Firmware update failure or other
abnormality.
5. LAN indicator(LINK/ACT)
Lights up when data is transmitted/received via LAN.
6. LAN connector
Use a category 5e or above LAN cable with a
maximum length of 100 m (328 ft.)
[Note]:
Use of an STP (shielded twisted pair) cable is
recommended.