R Heavy Duty CD player/weather Band Receiver with CD changer Control/XM Radio Ready CQ-5330U Operating Instructions CLK PWR ALM VOL PUSH SEL / SAT CQ-5330U DISP LOUD MODE MUTE DISC BAND BASS/TREB/BAL/FADER 1 APM CD SCAN 2 3 4 RPT RDM 5 6 TUNE SEEK SCAN ILL • Please read these instructions carefully before using this product and keep this manual for future reference.
Safety Information The following applies only in the U.S.A. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK OR PRODUCT DAMAGE, DO NOT EXPOSE THIS APPLIANCE TO RAIN, SPLASHING, DRIPPING OR MOISTURE. Part 15 of the FCC Rules FCC Warning: Any unauthorized changes or modifications to this equipment would void the user's authority to operate this device. CAUTION: PLEASE FOLLOW THE LAWS AND REGULATIONS OF YOUR STATE, PROVINCE OR COUNTRY FOR INSTALLATION OF THE UNIT.
Panasonic welcomes you to our ever growing family of electronic product owners. We know that this product will bring you many hours of enjoyment. Our reputation is built on precise electronic and mechanical engineering, manufactured with carefully selected components and assembled by people who take pride in their work. Once you discover the quality, reliability, and value we have built into this product, you too will be proud to be a member of our family.
Contents Safety Information(Part 15 of the FCC Rules). . . . . . . . . . . . . . . . . Page 2 Use this product safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 ❒ Power and Sound Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Power, volume, mute, loudness, display change, audio mode (Bass/Treble/Balance/Fader) ❒ Clock Setting . . . . . . . . . .
Power and Sound Controls Power Turn the key in the ignition until the accessory indicator lights. Power on: Press [PWR] (power). Power off: Press [PWR] (power) again. ACC ON Remote Control Signal Sensor Point the remote control unit (CA-RC 500U, option) at the unit's sensor. PWR VOL PUSH CLK ALM SEL / SAT CQ-5330U DISP LOUD MODE BAND BASS/TREB/BAL/FADER Volume Turn the knob clockwise to increase volume, and counterclockwise to decrease volume.
Power and Sound Controls (Continued) Audio Modes (Bass/Treble/Balance/Fader) Note: If no operation takes place for more than 5 seconds in audio mode (2 seconds in volume mode), the display returns to the regular mode. q Push [SEL] to select the audio mode. Volume Bass Treble Fader Balance push CLK PWR ALM VOL PUSH SEL / SAT CQ-5330U DISP LOUD MODE MUTE DISC BAND BASS/TREB/BAL/FADER 1 CD SCAN 2 3 4 APM Turn [VOL] (volume) clockwise or w counterclockwise to change each level.
Clock Setting Selecting the Clock Display The 12-hour system is used for the clock. Press [CLK] (clock) to switch clock and alarm time display both. clock display Initial Time Alarm time display “SET” is displayed when the clock is not adjusted. Note: if no operation takes place for more than 5 seconds in alarm time, the display returns to the clock display.
Alarm Time Setting The 12-hour system is used for the clock. Initial Alarm Time Press and hold [ALM] (Alarm) “AM 12:00” is displayed when the alarm is not adjusted. CLK PWR ALM VOL PUSH SEL / SAT CQ-5330U DISP LOUD MODE MUTE DISC BAND BASS/TREB/BAL/FADER 1 CD SCAN 2 3 4 APM Alarm Time Setting q Press and hold [ALM] (Alarm) and do not release to set alarm time. Display blinks and the alarm time setting mode is activated. (blink.) Hours w Press [{] to set the hour. (Hours set.
Radio q Radio Mode Press [MODE] to change to the radio mode. Radio CD Player a c CD Changer Control a ( When a CD changer is connected ) ( When CD disc loaded ) FM stereo indicator CLK PWR ALM VOL PUSH SEL / SAT CQ-5330U DISP LOUD MODE MUTE DISC BAND BASS/TREB/BAL/FADER 1 CD SCAN 2 3 4 RPT RDM 5 6 TUNE SEEK SCAN APM ILL w Band Press [BAND] to change the band. e Scan • Press [SCAN], each station will be scanned sequentially and the display will blink for 5 seconds.
Radio (Continued) Preset Station Setting Up to 6 stations can be saved in each of the FM1, FM2 and AM preset station memories. Note: Existing saved stations are overwritten with new stations after following this procedure. q Band Press [BAND] to select a desired band.
CLK PWR ALM VOL PUSH SEL / SAT CQ-5330U DISP LOUD MODE MUTE DISC BAND BASS/TREB/BAL/FADER 1 CD SCAN 2 3 4 RPT RDM 5 6 APM TUNE SEEK SCAN ILL Tuning in a Weather Band Station • Press [BAND] to select WB (Weather Band). (a page 9) • Press any of the buttons [1] to [6] to monitor the preset station. WB Weather Band Frequency (channel) Number Note: The weather band (CH1-6) has been preset. CH7 is selected by pressing [}] or [{].
CD Player Disc Insert and Playback Disc insert Playback will start automatically after the player recognized the loaded disc as an ordinary music CD. (When a CD-R or CD-RW which has CD-DA formatted data as the same as an ordinary music CD is loaded, this player recognizes it as an ordinary music CD.) u (eject) CQ-533 0U “LOAd” will be displayed until the disc is loaded. Label Side Notes: • Do not insert a disc when “DISC” indicator lights.
Cautions: • Only 5" (12 cm) CD, CD-DA data recorded CD-R and CD-RW discs are available for this unit. • This unit does not support CD text display. • This unit does not support MP3 and WMA disc playback. • Refer to page 23 about notes on CD-Rs/RWs. • This unit is not designed for any 3" (8 cm) disc. • If you insert an 3" (8 cm) disc and can not eject it, turn ACC of your car off once and turn it on again, then press [u] (eject). • Do not use irregular shaped discs.
CD Changer Control q CD Changer mode While a disc magazine is inserted in the CD changer, press [MODE] to select CD changer mode. Play starts from the first track. CLK PWR ALM VOL PUSH SEL / SAT CQ-5330U DISP LOUD MODE MUTE DISC BAND BASS/TREB/BAL/FADER 1 CD SCAN 2 3 APM w Disc Selection [1] ({ DISC): Previous disc. [2] (} DISC): Next disc. e Track Selection Press [TRACK 2] once to go to the next track. Press repeatedly to step forward through all the tracks.
Note: CD changer functions are applicable to units with optional CD changer unit. (sold separately) Scan Play (Tracks) • Press [4] (CD SCAN). The track number blinks and the first 10 seconds of each track on the discs play in sequence. • Press [4] (CD SCAN) again to cancel and continue with the current track. Scan Play (Discs) • Press and hold [4] (CD SCAN) for more than 2 seconds. The first track of all the discs in the magazine is played for 10 seconds each and Disc Number blinks.
XM Control Preparation: Connect the XM receiver (XM DIRECT MODEL:XM-RVR-D-001) to the Unit CQ-5330U. XM satellite radio is available on a chargable basis. q XM Mode r Channel Scan (When a XM receiver is connected.) Press [MODE] to change to the XM mode.
• When the display shows “CAT ON”, Press [2] (}): Up Press [1] ({): Down 1 2 1 (without operation during 5 seconds.) Category Name 2 Press [2] or [1]. (Receiving) (Received) Category Name (interdisplay for 2 seconds.) Push and hold the knob [SEL] for more than 2 seconds to resume the normal display. category on indicator Notes: CAT OFF: Every channel can be selected from every category. CAT ON: Only channels in the current category can be selected.
XM Control (Continued) Display Change Press and hold [MODE] (DISP) for more than 2 seconds. MODE Channel name (Press and hold) (Reading artist name) Artist name (Reading song title) song title (Reading categry) Category name Note: Display when there is no name/title or can not decode. XM ID Confirmation • Push and hold the knob [SEL] for more than 2 seconds and then push again during 2 seconds. (Push and hold) (Push) Note: If the ID number is 12345678 for example.
Troubleshooting Preliminary Steps Check and take steps as described in the tables below. If You Suspect Something Wrong Immediately switch the power off. Disconnect the power connector and check that there is neither smoke nor heat from the unit before asking for repairs. Never try to repair the unit by yourself because it is dangerous to do so. Cautions: • Do not use the unit if it malfunctions or if there is something wrong.
Troubleshooting (Continued) ❐ Radio Trouble Much noise in FM stereo and monaural broadcasts. Preset station is reset. Cause/Step Station is too far, or signals are too weak. a Select other stations of higher signal level. The radio antenna is not extended enough. a Extend fully the radio antenna. Battery cable is not correctly connected. a Connect the battery cable to the terminal that is always active. ❐ CD Trouble Cause/Step Disc is upside down.
❐ CD (Continued) Trouble Cause/Step Mounting angle is over 30˚. a Adjust mounting angle to less than 30˚. Sound skips due to vibration. Instable mounting. a Mount the unit securely with the mounting parts, referring to the section on installation. Disc is not ejected. • Disc is defective. • Mechanical trouble. a Press [u] (eject). If normal operation is not restored, call the store where you purchased the unit or the nearest Servicenter to ask for repairs. Time is counted but no sound comes out.
Troubleshooting (Continued) Error Display Messages ❐ CD Trouble Cause/Step Disc is dirty, or is upside down. A disc that has data other than CD-DA type is loaded. ➡ Check the disc. Disc has scratches. ➡ Check the disc. No operation by some cause. ➡ If normal operation is not restored, call the store where you purchased the unit or the nearest Servicenter to ask for repairs. ❐ CD changer Disc is dirty, or is upside down. ➡ Select the next available compact disc. Check the disc. Disc has scratches.
Maintenance Care of the Unit ❐ Cleaning this Unit ❐ Caution on Cleaning Use a dry, soft cloth to wipe. Never use solvents such as benzine, thinner as they may mar the surface of the unit. Notes on Discs Do not play any ordinary music CDs with labels other than this one. How to hold the disc • Do not touch the underside of the disc. • Do not scratch the discs. • Do not bend disc. • When not in use, keep the disc in the case. Label side Do not use irregular shaped discs.
Speaker Connections Caution: Please follow the instructions given below. Failure to do so will cause damage to the unit and speakers. L + - R+ - (White) + - (White w/black stripe) (Gray) + - (Gray w/black stripe) • Use ungrounded speaker only. • The maximum speaker input should be 37 W or more. (If used with the optional power amplifier, the speaker input should be higher than the maximum amplifier output.) • The speaker impedance should be 4 - 8 Ω.
Installation Guide WARNING ❐ This installation information is designed for experienced installers and is not intended for non-technical individuals. It does not contain warnings or cautions of potential dangers involved in attempting to install this product. Any attempt to install this product in a vehicle by anyone other than a qualified installer could cause damage to the electrical system and could result in serious personal injury or death.
Installation (Continued) ❐ Preparation ❐ Installation Hardware Warning: If your vehicle is equipped with air bag and/or anti-theft systems, specific procedures may be required for connection and disconnection of the battery to install this product. Before attempting installation of this electronic component, contact your vehicle dealer or manufacturer to determine the required procedure and strictly follow their instructions.
Cautions: • We strongly recommend that you wear gloves for installation work to protect yourself from injuries. • When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your hands and fingers. First complete the electrical connections, and then check them for correctness.(a page 29) The included Mounting Collar q is designed specially for this unit. Do not use it to attach any other model.
Installation (Continued) To Remove the Unit from the vehicle's dashboard Insert each Removal Tool i and pull. i Removal Tool (U-shaped) Note: Do not lose Removal Tools. They will be needed to remove the unit from the vehicle's dashboard.
Electrical Connections Cautions: • This wiring information is for experienced technical individual, for safety reason, please your dealer wire this connection. • This product is designed to operate with a 12 V DC, negative ground battery system. • To prevent damage to the unit, be sure to follow the connection diagram below. • Do not insert the power connector into the unit until the wiring is completed. • Be sure to insulate any exposed wires from a possible short-circuit from the vehicle chassis.
Electrical Connections (Continued) ❐ Upgrading the system (connect a XM receiver and the wired remote.) Note: For wiring, carefully read the operation instructions for the devices connected.
❐ Upgrading the system (connect a CD changer and the wired remote.) Note: For wiring, carefully read the operation instructions for the devices connected. XM control connector (2P connector) CQ-5330U CD changer connector (10P conncetor) Wired Remote Connector (8P connector) APM/PRG SEEK VOL TUNE RC330U PWR DISP BAND MODE DISP UP SEL - SAT Wired Remote ( CA-RC330U, option ) CD Changer (CD-DP880, option) Extension Cable for connecting the unit and CD changer.
Specifications ❐ General Power Supply: Current consumption: Maximum Power Output: Tone adjustment range: Bass: Treble: Power Output: Suitable Speaker Impedance: Dimensions (W × H × D): Weight: 12 V DC (11 V-16 V) test Voltage 14.4 V, Negative ground Less than 2.5 A (CD mode, 0.5 W 4-speaker) 37 W × 4 channels at 400 Hz, Volume Control maximum ± 12 dB at 100 Hz ± 12 dB at 10 kHz 18 W per channel into 4 ohms, 40 to 30 000 Hz at 3 % THD 4-8 Ω 7" × 1-15/16" × 6-1/10" (178 × 50 × 160 mm) 3 lbs. 12 oz (1.
MEMO 33 CQ-5330U
MEMO 34 CQ-5330U
Panasonic Consumer Electronics Company, Division of Matsushita Electric Corporation of America One Panasonic Way, Secaucus, New Jersey 07094 YFM284C420ZA TAMACO0204-0 Printed in Taiwan