Operating Instructions - Language - English

ManualsBrandsPanasonic ManualsAV ProductsCQC1100U

POWER

CLOCK

CQ-C1200U

DISP

MUTE

789101112SCAN

APM

SRC

REP

TUNE

TRACK

•

POWER

CLOCK

CQ-C1200U

DISP

MUTE

789101112SCAN

APM

BAND

SRC

REP

TUNE

TRACK

•

CQ-C1200U/C1120U/C1110U/C1100U

Hours

Press and hold [DISP] (clock) for more than 2

seconds.

e Press [k TUNE] or [l TUNE].

Minutes

Press [DISP] (clock).

t Press [k TUNE] or [l TUNE].

y Press [DISP] (clock).

Note: Press and hold [k TUNE] or [l TUNE] to

change numbers rapidly.

Audio Mode

(Bass/Treble/Balance/Fader/Sub Woofer)

Regular mode

Volume

Bass Treble

BalanceSub Woofer

Fader

Note: If no operation takes place for more than 5 sec-

onds in audio mode (2 seconds in volume mode), the

display returns to the regular mode.

Bass:

Adjustable range: –12 to +12 (by 2 dB step)

Treble:

Adjustable range: –12 to +12 (by 2 dB step)

Balance:

R (right speaker) or L (left speaker)

Fader:

F (front speaker) or R (rear speaker)

Push [SEL] to select the audio mode.

Clock Setting

The 12-hour system is used for the clock.

(Hours blink.)

(Hours set.)

(Minutes blink.)

(Minutes set.)

(End.)

Initial Time

q Press [DISP] (clock).

"AdJ" is displayed when the clock is not

adjusted.

Time Reset

Press and hold [DISP] (clock) for more than

2 seconds to activate the time setting mode to

reset the time. Then, repeat steps e to y.

[DISP] (clock)

[k TUNE], [l TUNE] (Hours, minutes)

Adjustable range: 1 to 15 (by 1 step) Balance center

Adjustable range: 1 to 15 (by 1 step) Fader center

(Only for CQ-C1200U)

Sub Woofer:

Adjustable range (level): MUTE (0) to 7

(Only for CQ-C1200U)

Push

Turn [VOLUME] clockwise or counterclockwise

to change each level.

default: 0 dB

(default)

default: 4

ISP

MUTE

SRC

Power and Sound Controls

Mute

Press [MUTE] to mute the sound completely.

lights

Press [MUTE] again to cancel.

Volume

Turn the knob clockwise to increase volume,

and counterclockwise to decrease volume.

Volume level (0 to 40)

(default: 18)

SQ (Sound Quality)

SQ is a function that can call up various sound types at

the touch of button in accordance with your listening

music type.

Press [SQ] to select a sound type as follows:

(default)

SQ -- (default) flat frequency response:

does not emphasize.

SQ - 1 (ROCK) speedy and heavy sound:

exaggerates bass and treble.

SQ - 2 (POP) wide-ranged and deep sound:

slightly emphasizes bass and treble.

SQ - 3 (VOCAL) clear sound:

emphasizes middle tone and

slightly emphasizes treble.

Power

Turn the key in the ignition until

the accessory indicator lights.

Power on: Press [SRC] (POWER).

Power off: Press [SRC](POWER)

again and hold.

ACC

MUTE

Display Change

Press [DISP] (display) to switch to the clock display.

Note: "AdJ" is displayed when the clock is not adjusted.

(

➡ page 13)

When the power is off:

No display Clock display

Remote control sensor (➡ page 18)*

(only for CQ-C1200U/C1120U/C1110U)

Down

SQ indicator

Notes:

• If no operation takes place for more than 2 seconds in the SQ mode, the display returns to the regular mode.

•

Settings of SQ, bass/treble are influenced one another. If the influence mentioned above causes distortion to audio signal,

readjust bass/treble or volume (➡ page 13).

• CQ-C1100U has no remote control function.*

Summary of content (11 pages)

PAGE 1
E N G L I S H Power and Sound Controls Note: If no operation takes place for more than 5 seconds in audio mode (2 seconds in volume mode), the display returns to the regular mode. Clock Setting Power Audio Mode (Bass/Treble/Balance/Fader/Sub Woofer) q Push [SEL] to select the audio mode. The 12-hour system is used for the clock. Display Change Turn the key in the ignition until the accessory indicator lights. Power on: Press [SRC] (POWER). Power off: Press [SRC](POWER) again and hold.
PAGE 2
E N G L I S H Caution: To ensure safety, never attempt to preset stations while you are driving. Preset Station Setting Display Change E N G L I S H Up to 6 stations each can be saved in the FM1, FM2, FM3 and AM preset station memories. Press [DISP] (display) to switch to the clock display. 4 Radio Mode Radio Press [SRC] (source) to change 3 to the radio mode.
PAGE 3
E N G L I S H E N G L I S H CD Player Disc Insert and Playback Disc insert 5 u (eject) Playback will start automatically after the player recognized the loaded disc as an ordinary music CD. (When a CD-R or CD-RW which has CD-DA formatted data as the same as an ordinary music CD is loaded, this player recognizes it as an ordinary music CD.) “LOAd” will be displayed until the disc is loaded. Label side Notes: • Do not insert a disc when “DISC” indicator lights.
PAGE 4
Only for CQ-C1200U/C1120U/C1110U E N G L I S H Remote Control Unit Anti-Theft System Battery Installation This unit is equipped with a removable face plate. Removing this face plate makes the radio totally inoperable. Remove the battery holder. Pull the battery holder by the position B while pushing position A in the direction indicated by the arrow. Install the battery on the battery holder. Place a battery in the holder with its “+” side facing up as shown in the figure.
PAGE 5
E N G L I S H E N G L I S H Troubleshooting Preliminary Steps Check and take steps as described in the tables below. 9 If You Suspect Something Wrong Immediately switch the power off. Disconnect the power connector and check that there is neither smoke nor heat from the unit before asking for repairs. Never try to repair the unit by yourself because it is dangerous to do so. Cautions: • Do not use the unit if it malfunctions or if there is something wrong.
PAGE 6
E N G L I S H E N G L I S H Troubleshooting (Continued) ❐ CD (Continued) 11 ❐ Remote Control Unit Trouble Sound skips due to vibration. Cause/Step Trouble Battery polarities are reversed. ➡Insert the battery correctly. Instable mounting. ➡Mount the unit securely with the mounting parts, referring to the section on installation. Wrong battery. ➡Check the battery. Disc is not ejected. Time is counted but no sound comes out. The first track of a mix mode disc was reproduced.
PAGE 7
E N G L I S H Maintenance 13 ❐ Cleaning this Unit ❐ Caution on Cleaning Use a dry, soft cloth to wipe. Never use solvents such as benzine, thinner as they may mar the surface of the unit. E N G L I S H Installation WARNING Care of the Unit Notes on discs Do not play any ordinary music CDs with labels other than this one. 14 ❐ This installation information is designed for experienced installers and is not intended for non-technical individuals.
PAGE 8
E N G L I S H Installation (Continued) 15 The first step in installation is to identify all the car wires you’ll use when hooking up your sound system. As you identify each wire, we suggest that you label it using masking tape and a permanent marker. This will help avoid confusion when making connections later. ❐ Identify All Leads Note: Do not connect the power connector to the stereo unit until you have made all connections.
PAGE 9
E N G L I S H E N G L I S H Installation (Continued) ❐ Preparation ❐ Installation Hardware Warning: If your car is equipped with air bag and/or anti-theft systems, specific procedures may be required for connection and disconnection of the battery to install this product. Before attempting installation of this electronic component, contact your car dealer or manufacturer to determine the required procedure and strictly follow their instructions.
PAGE 10
E N G L I S H E N G L I S H Electrical Connections Only for CQ-C1200U Cautions: • This product is designed to operate with a 12 V DC, negative ground battery system. • To prevent damage to the unit, be sure to follow the connection diagram below. • Strip about 5 mm of the lead ends for connection. • Do not insert the power connector into the unit until the wiring is completed. • Be sure to insulate any exposed wires from a possible short-circuit from the car chassis.
PAGE 11
E N G L I S H To Remove the Unit 1 Specifications Switch off the power of the unit. ❐ General Power supply: Current consumption: Maximum power output: 21 2 Remove the removable face plate. q Press [ ]. The removable face plate will be opened. w Push the face plate to either the right or left. e Pull it out towards you. Contact w q Press 3 Remove the Trim Plate u with a screwdriver.