Operating Instructions - Language - English

CQ-C9800N/C9700N
Radio
English
1716
Radio
A radio DSP is integrated into this unit. The IF filter allows the radio to adjust the bandwidth automatically to maintain optimum
reception.
CQ-C9800N/C9700N
Up to 6 stations can be preset in AM (MW/LW), FM1,
FM2, and FM3 respectively.
Preset stations can be simply called up by pressing [}]
(P·SET) or [{] (P·SET).
Note: Direct selection can be executed with [1] to [6]
buttons on remote control.
Auto Preset Memory (APM)
Six stations with the first highest to the 6th highest in
signal strength will be preset to each band.
1
Select a band.
2
Hold down [BAND]
(APM) for 2 sec.
or more.
The preset stations under best receiving conditions
are received for 5 sec. each after presetting the sta-
tions (SCAN). To stop scanning, press [}] or [{].
Notes:
¡ New stations overwrite existing saved stations.
¡
Only RDS stations will be saved at default setting (AF ON).
To select non RDS stations too, set AF OFF.(a page 19)
Manual station preset
1
Tune in to a station.
2
Hold down [}] or [{] for 2 sec. or
more.
3
Select a preset number by pressing [}]
or [{].
4
Preset the station by holding down [}]
or [{] for 2 sec. or more.
Frequency/preset number blinks once.
Notes:
¡ New stations overwrite existing saved stations.
¡ In step 2, a station can be registered by holding down
the numeric button [1]~[6] for 2 sec. or more.
¡ To stop presetting stations, press [DISP] (Display).
1
Press [SOURCE] to select the radio
mode.
2
Press [BAND] to select a band.
Notes:
¡
For tuning in on only stations whose receiving
conditions are good in the station search, set
LOCAL to ON. (
a page 17)
¡ For reducing noise when a receiving FM stereo
wave is weak, set FM MONO to ON. (
a page 17)
3
Select a station.
Frequency adjustment
[]] (TUNE): Lower
[[] (TUNE): Higher
Note: Hold down for 0.5 sec. or more and release
for station search.
Preset station selection
[{] (P·SET: Preset): Lower preset number
[}] (P·SET: Preset): Higher preset number
Note: Direct selection can be executed with [1] to
[6] buttons on remote control.
Band Frequency
Lights when LOCAL is
activated.
(a page 17)
Preset Number
Station Preset
(APM: Auto Preset Memory, P·SET: Preset)
Radio mode display
Note: In AM mode, only LOCAL can be selected.
1
Press [MENU] to display the menu dis-
play.
For using the remote
control, hold down
[MENU] for 2 sec. or
more.
2
Press [}] or [{] to select a mode to be
adjusted.
3
Press [BAND]
(SET) to adjust.
4
Press [MENU] to confirm the adjust-
ment.
For using the remote control, hold down [MENU]
for 2 sec. or more.
MONO (Monaural)
Noise reduction when the signal strength decreases
LOCAL
Setting when searching for a station
Mono/Local Setting (Radio Menu Display)
(MONO/LOCAL)
Lights while receiving an
FM stereo signal.
Lights when MONO is
activated.
(a page 17)
Receiving in stereo
(Default)
Receiving in mono and
reducing the noise level
( lights.)
Searching even for a
relatively low-intensity
radio wave station
(Default)
Searching only for a high-
intensity radio wave
station (
lights.)
Operation Flow
CQ-C9800N
BANDBAND
CQ-C9800N
BANDBAND
CQ-C9800N
BAND
CQ-C9800N
BANDBAND