Operating instructions

39
CQ-VX1300W
1
E
N
G
L
I
S
H
38
CQ-VX1300W
25
E
N
G
L
I
S
H
26
❏ Precautions
Be sure to remove the bracket for transportation
before use (installation).
CUse
Binding-Head Screws
(5 mm φ x 8 mm)
for installation.
Be careful not to lose any of these
screws.
Transportation Bracket x 2
CQ-VX1300W
Binding-Head Screw
(5 mm φ × 8 mm) x 4
¡We strongly recommend that you wear gloves for installation work to protect yourself from injuries.
¡When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your
hands and fingers.
CQ-VX1300W
❏ Typical Installation (For cars with double-DIN size)
1. Remove car radio or little object box from the car and the stopping brackets.
2. Use the appended screws w or e to install the brackets on this unit.
3. Install this unit into the car.
¡If a special kit (option) is necessary for a certain year’s, model or grade of
car, please consult your dealer.
¡For simple electrical connection to your car, you can buy a prepared power
connector from your dealer.
Transportation bracket removal
Notes:
¡The screw holes on the right side are
not tapped. Please only use screws provided to mount the unit.
¡To tighten the screws, press its head down straight forward.
❏ Installation for except for the above types
For general use kit (option) or motor’s special kit (option), please consult your dealer.
Note: Use pliers to bend the fingers
on the bracket vertically.
Bracket (L)
Bracket (R)
Appended Screws (w or e).
Select appropriate ones matching
the hole shape of the bracket.
Note: Binding-Head Screws (5 mmφ
x 8 mm) w are appended four
pieces, the other four pieces are fixed
on the transportation bracket.
w Binding-Head
Screw x 8
(5 mmφ x 8 mm)
e Flat-Head Screw
x 8
(5 mmφ x 8 mm)
Installation
❏ Check the supplied items
against the table
If there is a difference between them, please inform the
dealer where you purchased the unit.
❏ Installation dimensions and
angle
● The unit cannot be installed in some car types (due to
the shape and dimensions of a dashboard), and the unit
may interfere with a gearshift lever or other objects in
some car types. Ask the dealer for further information.
Consult the dealer if space for an audio system is not
designed for 2-DIN (180 (W) mm x 100 (H) mm).
● Install the unit at 30 degrees or less with respect to a
horizontal axis.
30°
Caution: Do not disconnect the battery terminals of a
car with trip or navigational computer since all user set-
tings stored in memory will be lost. Instead take extra
care with installing the unit to prevent shorts.
❏ Installation Flow
1
Disconnect the cable from the negative
@
battery terminal (see caution on the right).
First complete the electrical connections,
and then check them for correctness.
(a page 40-42)
●
Please carefully read the operating and installation
instructions of the respective equipment before con-
necting it to this unit.
●
Please connect the power lead (red) after all other
connections are made.
Install.
After installation reconnect the negative
@
battery terminal.
2
3
4
Note: Binding-Head Screws (5 mmφ x 8 mm) w are
appended four pieces, the other four pieces are fixed on the
transportation bracket.
We strongly recommended that you wear
gloves for installation work to protect your-
self from injuries.
WARNING
This installation information is designed for experienced installers
and is not intended for non-technical individuals. It does not contain
warnings or cautions of potential dangers involved in attempting to
install this product.
Any attempt to install this product in a motor car by anyone other
than qualified installer could cause damage to the electrical system
and could result in serious personal injury or death.
●Supplied Hardware
No. Item Q'ty
q
Power Connector 1
w
Binding-Head Screws (5 mm
φ ×
8 mm) 8
e
Flat-Head Screws (5 mm
φ ×
8 mm) 8