Operating Instructions Access and Operation by Web Browser Intelligent Controller Model No. CZ-256ESMC1U Before operating the unit, read these operating instructions thoroughly and keep them for future reference.
CONTENTS CONTENTS 1. COMPUTER ENVIRONMENT REQUIREMENTS .........................................................................1 2. LOG-IN........................................................................................................................................... 1 3. SCREEN DISPLAY AND OPERATION.........................................................................................2 3-1. [Each Tenant] Screen ..................................................................................
ACCESS AND OPERATION BY WEB BROWSER ACCESS AND OPERATION BY WEB BROWSER Accessing the Intelligent Controller from your computer allows you to monitor/operate air-conditioning equipment using a Web browser. 1. COMPUTER ENVIRONMENT REQUIREMENTS In order to use the web browser of your computer to connect to the Intelligent Controller and monitor/operate air-conditioning equipment, the following environment requirements must be met. Supported browser : Internet Explorer 6.
SCREEN DISPLAY AND OPERATION 3. SCREEN DISPLAY AND OPERATION 3-1. [Each Tenant] Screen After you log in to the Intelligent Controller, or when you use the menu to select [1. Status/Control : 1. Each tenant], a screen such as shown below appears. (Screen details may differ depending on the user logged in.) New button Updates the screen to the latest information. Menu (The menu may differ depending on the user logged in. The following menu appears when logged in as an administrator.
SCREEN DISPLAY AND OPERATION Tenant list Shows the indoor unit and tenant structure currently accessed by the Intelligent Controller in a list. Select indoor units by clicking different parts of the list. Clicking on the part highlighted in the screen example above will select the individual indoor unit, while clicking on the tenant name (Tenant001, Tenant002, etc. in the example) will select all indoor units for that tenant.
SCREEN DISPLAY AND OPERATION B Control section Shows controls for possible operation steps such as start/stop switching, operation mode selection, temperature selection, fan speed setting, fan direction setting etc. If the logged in user has only general user privileges, buttons for restricted operation steps will be grayed out (inactive). The REMOTE CONTROL and CHECK buttons will not be displayed. C Send button Sends the changes made to the Intelligent Controller. D Cancel button Cancels the changes made.
SCREEN DISPLAY AND OPERATION 3-2. [Each Tenant Details] Screen When you use the menu to select [1. Status/Control : 2. Each tenant details], a screen such as shown below appears. (Screen details may differ depending on the user logged in.) Operation principles for this screen are similar to those of the “3-1. [Each tenant] screen”. 3-3. [All Units] Screen When you use the menu to select [1. Status/Control : 5. All units], a screen such as shown below appears.
SCREEN DISPLAY AND OPERATION 3-4. Distribution Ratio/Usage: Data Download Screen When you use the menu to select [3. Distrib. ratio/Usage : 3. Download] while logged in as an administrator, a screen such as shown below appears. You can download files by selecting them and clicking the “Download” button. A cut-off data file appears for each piece of cut-off data that appears on the Intelligent Controller unit.
SCREEN DISPLAY AND OPERATION 3-5. Alarm Log Screen When you use the menu to select [4. Maintenance/Test Run : 2. Alarm log] while logged in as an administrator or special user, a screen such as shown below appears. When an indoor unit is selected in the tree section, the previous 14 occurrences are displayed. (Same as the display on the Intelligent Controller.) “I/D alarm log”, “O/D comm. error log”, and “Adaptor alarm log” can be selected from the drop-down list.
SCREEN DISPLAY AND OPERATION [O/D comm. error log] logs the history of errors in communication between the outdoor unit and the Intelligent Controller or the communication adaptor. [Adaptor alarm log] logs the history of warnings as determined by the Intelligent Controller or the communication adaptor. (Duplicate adaptor addresses, communication error between the Intelligent Controller and adaptor, etc.
SCREEN DISPLAY AND OPERATION 3-6. Mail Send Log Screen When you use the menu to select [4. Maintenance/Test Run : 4. Sent mail log] while logged in as an administrator, a screen such as shown below appears. ⑧ No. The entry numbers for the sent mail log. With a maximum of 20 (No. 1 to 20) possible entries, the newest entries appear at the top of the list. When the number of entries exceeds 20, entries are deleted starting with the oldest.
SCREEN DISPLAY AND OPERATION 3-7. Program Timer Screen When you use the menu to select [6. Auxiliary settings : 3. Program timer] while logged in as an administrator, or use the “CHECK” button for timer operation in the remote control window, a screen such as shown below appears. (As non-administrator users can only confirm settings and not configure them, the “Cancel” and “Send” buttons only appear when logged in as an administrator.
SCREEN DISPLAY AND OPERATION You can only configure daily timer settings one number (D1, D2, etc.) at a time. If you attempt to switch to D2 settings in the middle of configuring D1 settings, for example, the message “Send for each daily timer.” appears. In such a case, apply or cancel the current settings by clicking the “Send” or “Cancel” button, respectively, before configuring the next daily timer number. For details on the settings, refer to the operation manual for the Intelligent Controller.
SCREEN DISPLAY AND OPERATION 3-8. Tenant Holiday/Timer Special Day Screen When you use the menu to select [6. Auxiliary settings : 4. Ten.Ho/TimerSp.Day] while logged in as an administrator, a screen such as shown below appears. Tree section “Cancel”/”Send” buttons “Copy” button You can only configure tenant holiday/timer special day settings one tenant at a time.
SCREEN DISPLAY AND OPERATION 3-9. Prohibit Remote Control Screen When you use the menu to select [6. Auxiliary settings : 5. Prohibit R/C] while logged in as an administrator, or click the “CHECK” button for prohibit remote control in the remote control window, a screen such as shown below appears. (As non-administrator users can only confirm settings and not configure them, the “Cancel” and “Send” buttons only appear when logged in as an administrator.
SCREEN DISPLAY AND OPERATION 3-10. WEB Settings Screen When you use the menu to select [6. Auxiliary settings” : 10. WEB settings] while logged in as an administrator, a screen such as shown below appears. “Cancel”/”Send” buttons To [3.10.1. Server details] screen For details on the settings, refer to the operation manual for the Intelligent Controller. Input values have the following restrictions.
SCREEN DISPLAY AND OPERATION If a value that is outside the input range or input limitations is set, the window below appears. If the network settings have been changed when the “Send” button is clicked, the window below appears. Always check there is no problem restarting the Intelligent Controller unit. When “YES” is clicked for submission, the screen changes as shown below, and the Intelligent Controller unit restarts.
SCREEN DISPLAY AND OPERATION When a mail test is sent, the window below appears when the mail settings have been changed. In this case, either click the “Send” button to enable the mail setting changes or click the “Cancel” button to disable the changes, and then send the mail test again. If the Intelligent Controller unit is processing (check configuration, cut-off, backup, etc.), this screen cannot be displayed or updated, mail test cannot be sent, and setting change “Send” cannot be performed.
SCREEN DISPLAY AND OPERATION Input values have the following restrictions. Setting Item Input Range Port number Numbers 0 to 999999 User ID Up Password characters and symbols to 50 Input Character Limitations alphanumeric 3-10-1-1. Receiving server settings When you click the “Receiving server settings” button from the [Server details] screen, a screen such as shown below appears. For details on the settings, refer to the operation manual for the Intelligent Controller.
SUPPLEMENTARY INFORMATION 4. SUPPLEMENTARY INFORMATION ■ When connecting the Intelligent Controller via Internet, consider implementing network security measures, such as a firewall. ■ Error Messages Error Cause Remedy The system configuration System configuration change! (when logged in with Administrator of the Intelligent Controller has changed. privileges) This is a warning message. Wait a moment and resume operation. Intelligent Controller is now processing, please wait. Please try later.
SUPPLEMENTARY INFORMATION 19
SUPPLEMENTARY INFORMATION 20
SUPPLEMENTARY INFORMATION 21
DC1011-11111 Printed in Japan
