DVD Recorder Model No. DMR-EZ485V DMR-EZ48V P15 Basic Operations Operating Instructions Dear customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. Before connecting, operating or adjusting this product, please read the instructions completely. Please keep this manual for future reference. Region number supported by this unit Region numbers are allocated to DVD players and DVD-Video according to where they are sold.
Precautions CAUTION! THE FOLLOWING APPLIES ONLY IN THE U.S.A. THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where 2) Keep these instructions. they exit from the apparatus. 3) Heed all warnings.
Table of Contents, Accessories Getting Started Precautions............................................................................... 2 IMPORTANT SAFETY INSTRUCTIONS .................................. 3 Unit Care ........................................................................................ 3 Accessories ................................................................................... 5 Remote Control Information ...........................................................
Reference Disc Information...................................................................... 74 Usable Discs for Recording and Playback ................................... 74 Play-only Discs ............................................................................ 75 Discs that Cannot be Played ........................................................ 75 Media Care .................................................................................. 75 MP3s, DivX and Still Pictures (JPEG) .............
Control Reference Guide Main Unit Remote Control signal sensor Cassette compartment Disc tray OPEN/CLOSE EJECT CH REC DRIVE SELECT POWER COPYING SD CARD IN 2 S VIDEO VIDEO L /MONO AUDIO R RESET The unit’s display Opening the front panel Pull down. REC COPYING DVD/VHS drive indicator ................................( Cassette eject button .....................................( 15) Disc tray open/close button ............................
DVD/VHS POWER POWER DRIVE SELECT VOL TV/VIDEO CH TRACKING/V-LOCK 1 2 3 4 5 6 7 8 9 DELETE 0 RESET CH INPUT SELECT FAVORITE SLOW/SEARCH SKIP/INDEX STOP REW PAUSE FF PLAY CM SKIP TIME SLIP/ JET REW TIO FUNC DIRECT NAVIGATO R SCHEDULE NS OK SUB MENU AUDIO A REC RETURN CREATE DISPLAY CHAPTER VCR/TV B REC MODE F Rec STATUS Getting Started Remote Control Turn the unit on or off ................................................ ( 12) Select drive (DVD, VHS, SD or USB) ............
Basic Connection The connection diagrams represent typical installations. These diagrams may not work with certain inhouse cable systems, master antenna installations, or situations where TV programming is delivered using methods that differ from industry accepted practices. If you require assistance with connections, please contact Panasonic at 1-800-211-7262 (for U.S.A.) or 1-800-561-5505 (for Canada).
Please check with your Cable Service Provider to verify whether the coaxial cable from the Cable Wall Jack must be connected to your Cable Box first, before connecting to other devices. Consult your cable service provider about the appropriate cable box to use. Additional coaxial cable and audio/video (AV) cable are required. Getting Started Connecting to a Television and a Cable Box Note: The terminals on the rear of your TV and cable box may not appear as shown below.
Basic Connection Connecting to a Television and a Satellite Receiver Consult your satellite service provider about the appropriate satellite receiver to use. Additional coaxial cable and audio/video (AV) cable are required. Note: The terminals on the rear of your TV and satellite receiver may not appear as shown below. Please read terminal labels carefully to ensure correct connections.
Getting Started You can enjoy high-quality picture and audio by changing the audio/video (AV) cable connection between this unit and your TV as shown on pages 8 to 10 and by doing the following. Connecting to a TV with an HDMI (High Definition Multimedia Interface) Cable When connected to an HDMI compatible unit, an uncompressed digital audio and video signal is transmitted, enabling you to enjoy high quality digital video and audio with just one cable.
Setting the Channels and Clock Preparation: Turn on the TV and select the appropriate video input to suit the connections to the unit. (Example: AV input, CH3 or CH4) These are the first settings you make upon buying the unit. You don’t need to make these settings again. DVD/VHS POWER POWER DRIVE SELECT TV/VIDEO CH VOL TRACKING/V-LOCK DVD/VHS POWER to turn the unit on. “HELLO” appears on the unit’s display.
The types of transmission: , to select “Antenna” or Automatic Clock and Channel Settings “Cable”, then OK Please select the wire connected to RF IN. Antenna Perform steps 1–6 on page 12. , to select the item you want to change. Cable Set Clock Manually Month OK 1 Day / 1 / Year Hour 2000 SAT 12 OK to start automatic channel/ clock setting. Confirm the time, then OK – DST (Daylight Saving Time) shows the summertime setting.
Setting the Channels and Clock Acquiring the setting information from the TV (VIERA) If this unit is connected to a Panasonic TV (VIERA) supporting HDAVI Control 3 via an HDMI cable, then the setting information on the TV is acquired by this unit when the unit is turned on for the first time. Please proceed to the following steps. The following screen is displayed in the language set on the VIERA television. –The language setting screen may be displayed depending on the usage environment.
Media Handling Inserting Discs Inserting USB memory Preparation Before inserting any USB memory to this unit, ensure that the data stored in it has been backed up. Opening the front panel Inserting the USB memory Check the orientation of the USB connector and insert it straight in. CH Basic Operations to open the tray. – Insert a disc. – Press [ OPEN/CLOSE] again to close the tray. Getting Started You can insert the USB memory directly into the USB port.
Watching Television This DVD recorder has a tuner which allows it to directly receive and record analog and terrestrial digital channels. High Definition (HD) programming is “down-converted” and recorded in Standard Definition (SD). Preparation: Turn on the television and select the appropriate video input to suit the connections to this unit (Example: AV input, CH3 or CH4). to turn the unit on. – “HELLO” appears on the unit’s display.
Playback DVD/VHS Playing a Disc Refer to “Advanced Disc Playback” ( 30–31) for detailed information on playback of discs. [RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] [DVD-V] [-RW‹VR›] [CD] DVD/VHS POWER to turn the unit on. –“HELLO” appears on the unit’s display. DRIVE SELECT to select the DVD drive. –The DVD indicator lights up on the unit. POWER POWER DRIVE SELECT CH T TV/VIDEO TRACKING/V-LOCK 1 2 3 4 5 6 7 8 9 DELETE 0 RESET to open the tray (Button located on front of the unit).
Recording Television Programs Refer to “Important Notes for Recording” ( 23) and “Advanced Recording” ( 24–26) for detailed information on recording. [RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] [VHS] Digital broadcasts cannot be recorded to video tape. Preparation: Turn on the television and select the appropriate video input to suit the connections to this unit (Example: AV input, CH3 or CH4). [RAM] If the disc is protected, release protection ( 52). [VHS] Ensure accidental erasure tab is intact.
Scheduled Recording Refer to “Advanced Scheduled Recording” ( 27) for detailed information on scheduled recording. [RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] [VHS] Digital broadcasts cannot be recorded to video tape. DVD/VHS POWER POWER Preparation: Turn on the television and select the appropriate video input to suit the connections to this unit (Example: AV input, CH3 or CH4). [RAM] If the disc is protected, release protection ( 52). [VHS] Ensure accidental erasure tab is intact ( 15).
Copying Recordings Copying Recordings (VHS DVD) When copying begins, the VHS tape is played back starting at the tape’s current position, and recorded to the disc. [VHS] [RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] CH REC COPYING Preparation: Turn on the television and select the appropriate video input to suit the connections to this unit (Example: AV input, CH3 or CH4). [RAM] If the disc is protected, release protection ( 52). Insert a disc with enough space for recording.
Copying Recordings (DVD VHS) All recordings on the disc are automatically copied onto the tape. If you start copying when the resume function is activated, the DVD is copied from the beginning of the recording where you previously stopped. To copy a whole disc, press [ STOP] to deactivate it before copying ( 17). CH REC COPYING COPYING indicator Preparation: Turn on the television and select the appropriate video input to suit the connections to this unit (Example: AV input, CH3 or CH4).
Deleting Recordings Important: Once deleted, contents cannot be recovered. Preparation: Turn on the television and select the appropriate video input to suit the connections to this unit (Example: AV input, CH3 or CH4). Insert the disc containing the recording to be deleted. [RAM] If the disc is protected, release protection ( 52).
Important Notes for Recording [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] Select the Main or SAP audio before recording. You can change the audio during playback ( Changing Audio during Playback). [ 61, Multi-channel TV Sound (Analog)] The selected audio only is recorded. Main If you record from external Hello equipment ( 28) Select “Main” or “SAP” on the external equipment. Main SAP Hello Hola 31, 38 If you record from external equipment ( 28) Select both “Main” and “SAP” on the external equipment.
Advanced Recording DVD Recording Modes and Estimated Disc Recording Time DVD-RAM Single-sided (4.7 GB) Double-sided1 (9.4 GB) DVD-R,DVD-RW, +R, +RW (4.7 GB) DVD-R DL3, +R DL3 (8.
When the format confirmation screen is displayed Important: Formatting permanently deletes all disc contents (including computer data), regardless of protection status of disc. [RAM] [-RW‹V›] [+RW] The following screen may appear when inserting a new disc, etc. Selecting Audio Channels to record Refer to “Recording of multilingual broadcasts” for detailed information ( 23).
Advanced Recording Playing while you are recording Specifying the Recording Time [RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] [VHS] Digital broadcasts cannot be recorded to video tape. This function allows specifying the length of recording time up to 4 hours. You can play DVD or VHS while recording to the other drive. The recording will not be affected − DVD playback ( 17) − VHS playback ( 17) Notes During recording REC repeatedly until the desired time is reached.
Advanced Scheduled Recording To cancel a scheduled recording in progress DRIVE SELECT to select the drive. Notes If the program schedule is changed by the TV station, then this unit will not be able to detect the change. The password screen appears when setting parental ratings ( 56). Unless you enter the correct password, recording a program with parental ratings may fail. Tips STOP You can enter up to 16 programs a month in advance. Schedule List – Confirmation screen appears.
Recording from an External Device Recording from a VCR, etc. Recording to DVD Connect cables while the power to both the unit and the external device is off. Front of the unit [RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] Perform steps 1−5 left. Start play on an external device. REC S VIDEO VIDEO IN 2 You can get a sharper, clearer picture by connecting with an S Video cable instead of the yellow video cable. L /MONO AUDIO R Yellow White Red to start recording the program from an external device.
Recording from a DV Camcorder Connect the cable while the power to both the unit and the external device is off. Front of the unit REC MODE to select the recording mode for the disc ( 24). to select “Rec.”, then OK 4-pin DV Cable [RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] Preparation: Turn on the unit. Insert a disc with enough remaining blank space. [RAM] If the disc is protected, release protection ( 52). Turn ON the DV equipment and pause play where you want to begin recording.
Advanced Disc Playback Zoom in on video Tips To select the recording with the numbered buttons e.g., “5”: [0] [5] “15”: [1] [5] During playback SUB MENU To view other pages Press [, , , ] to select “Previous” or “Next”, then press [OK]. – You can also press [, ] to view other pages. To exit the DIRECT NAVIGATOR screen Press [DIRECT NAVIGATOR]. DIRECT NAVIGATOR screen icons To zoom in: Protected. , to select “Zoom In”, then Not recorded due to recording protection (Digital broadcasts, etc.
Quick View (Play 1.3) [RAM] Allows you to increase the play speed slightly without distorting the audio. CM Skip [RAM] [-R] [-R\DL] [-RW‹V›] [+R] [+R]DL] [+RW] [-RW‹VR›] Skips 1-minute forward with each press. During playback During playback PLAY CM SKIP (Press and hold.) – Press again to return to normal speed.
Playing Playlists [RAM] [-RW‹VR›] You cannot create or edit playlists on this unit. However, you can play a playlist that has been created or edited on other equipment. DRIVE SELECT to select the DVD drive.
Playing MP3s [-R] [-R\DL] [CD] [USB] MP3 recorded on DVD-R, DVD-R DL, CD-R/RW or USB memory can be played on this unit. [USB] The screen shown below may be displayed when you insert a USB memory ( 15). USB Media Device Operations USB Media Device inserted. Select an action or press RETURN to Exit. Go to DivX Menu Play MP3 Go to Album View Copy pictures OK Tips To select file type 1. Press [RETURN]. 2. Press [FUNCTIONS]. 3. Press [,] to select “Menu”, then press [OK]. 4.
Playing Still Pictures (JPEG) [RAM] [-R] [-R\DL] [CD] [SD] [USB] Still pictures (JPEG) recorded on DVD-RAM, DVD-R, DVD-R DL, CD-R/RW, SD Memory Cards or USB memory can be played on this unit. [SD] [USB] The screen shown below may be displayed when you insert an SD card or USB memory ( 15). e.g., [USB] USB Media Device Operations , , , to select a picture, to view. then OK Notes USB Media Device inserted. Select an action or press RETURN to Exit.
Zoom Slideshow with soundtrack It is possible to play MP3 music recorded on a USB memory during a Slideshow. While playing a picture SUB MENU Preparation: Insert a USB containing MP3 files.
Playing DivX [-R] [-R]DL] [CD] [USB] You can play CD-R/CD-RW, DVD-R, DVD-R DL discs and USB memories which contain DivX video contents that have been recorded on a computer. [USB] When you insert a USB memory, the menu screen appears. ( 33, left column) Press [, ] to select “Go to DivX Menu”, then press [OK]. You can proceed to step 3 ( below). [-R] [-R\DL] ]CD]When you insert a disc containing MP3 files, DivX video contents and still pictures (JPEG), the files selection screen appears.
Advanced Video Cassette Playback Zoom in on video During playback Tips For quicker operation Hold [, ] to start cue/review and release the button to restart normal playback. SUB MENU Jet Search Allows high speed search of video in forward or reverse direction. , to select “Zoom In”, then OK During playback FF REW Tips To return the picture to its original size Press [, ] to select “Zoom out” in step 2, then press [OK].
Advanced Video Cassette Playback S-VHS Quasi Playback (SQPB) This unit can play tapes recorded in S-VHS. Some picture noise may occur depending on the type of tape used. It is not possible to fully obtain the high resolution S-VHS is capable of. This unit cannot record in S-VHS. Repeat Playback Adjusting the playback picture Manual Tracking The unit usually makes tracking adjustments automatically, but you may need to do it manually if noise appears on a tape recorded on other equipment.
Status Messages The following messages and displays appear to let you know what operations are being performed and the status of the unit. STATUS – Press [STATUS] to cycle through available displays. e.g., DVD-RAM Play 4 - 1 KPO-SD English VHS Rec. to display on-screen indicators. v Remain 1:45 SP v T12 0:12:34 SP CH 4- KPO-SD DVD-RAM Play 4 - 1 KPO-SD English VHS Rec. 0:00.
Linked Operations with the TV (VIERA Link TM “HDAVI Control TM”) You can enjoy linked operations with the TV and receiver by using “HDAVI Control”. What is VIERA Link “HDAVI Control”? VIERA LinkTM is a new name for EZ SyncTM. VIERA Link “HDAVI Control” is a convenient function that offers linked operations of this unit, and a Panasonic TV (VIERA) or receiver under “HDAVI Control”. You can use this function by connecting the equipment with an HDMI cable.
Easy control only with VIERA Remote Control If you connect this unit via HDMI cable to a TV with “HDAVI Control 2 or “HDAVI Control 3” function, you can operate both units more conveniently. You can operate this unit using the following buttons on the TV remote control. [, , , ], [OK], [RETURN], [SUB MENU]. Use the remote control for this unit to operate any other buttons (numbered buttons, etc.) that are not listed above. Refer to TV operating instruction for operating the TV.
Entering Text FUNCTIONS Window By using the FUNCTIONS window you may access the main functions quickly and easily. When viewing the Name screen. Recording Name _ With the unit stopped FUNCTIONS DVD-RAM Cartridge Protection Off Disc Protection Off Playback Program FUNCTIONS DVD-RAM Cartridge Protection Off Disc Protection Off delete Playback Playlists Copy Program Flexible Recording delete DV Camcorder Rec.
Recordings−Editing Tips Tips Recording/Chapter Normally, programs are recorded as a single item consisting of one chapter. Recording Chapter Start End To exit the menu screen Press [DIRECT NAVIGATOR]. To view other pages Press [, , , ] to select “Previous” or “Next”, then press [OK]. –You can also press [, ] to view other pages. Multiple editing Select with [, , , ], then press [PAUSE]. (Repeat.) –A checkmark appears. Press [PAUSE] again to cancel.
Recordings−Editing Setup Protection/Cancel Protection Tips Perform steps 1−4 of “Accessing the Recording View” ( 43). [RAM] Use to prevent accidental erasure of recordings. , to select “Setup Protection” or “Cancel Protection”, then OK DIRECT NAVIGATOR DVD-RAM The lock symbol appears when the recording is protected. Divide Recording Perform steps 1−4 of “Accessing the Recording View” ( 43).
Chapters−Creating, Editing Accessing the Chapter View Chapter Operations [RAM] Allows individual viewing and editing of chapters. DRIVE SELECT Create Chapter Perform steps 1−7b of “Accessing the Chapter View” ( left). to select the DVD drive. , to select “Create Chapter” then OK DIRECT NAVIGATOR Create Chapter DVD-RAM [RAM] When the Album View screen is displayed, press A to switch to the Recordings screen. 08 A Video Play B Picture Create Exit 0:43.21 OK at the point you want to divide.
Still Pictures−Editing Accessing the Album/Picture View [RAM] [SD] [USB] DRIVE SELECT Tips To view other pages Press [, , , ] to select “Previous” or “Next”, then press [OK]. –You can also press [, ] to view other pages. to select the drive (DVD, SD or USB). [RAM] When the Recordings screen is displayed, press B to switch to the Album View screen.
Album Name Only when you select “Create Album” , to select “Yes” or “No”, then Perform steps 1−4 of “Accessing the Album/Picture View” ( 46). OK If “Yes” is selected: You can give a name for the album ( 42). If “No” is selected: The recording date of the first picture in the album becomes the album name. , to select “Album Name”, then OK – You can give a name for the album ( 42). Notes Album names entered using this unit may not display on other equipment.
Copying Still Pictures Importing Still Pictures from an SD card or USB memory [SD] [USB] [RAM] This unit saves information about imported still pictures. Therefore, if still pictures are imported from the same SD card or USB memory, then only new still pictures will be imported. Copying Still Pictures via the Album View Screen When you insert an SD card or USB memory, the menu may be displayed. Press [RETURN] to exit the screen. e.g., [SD] SD Card Operations SD Card inserted.
Deleting Still Pictures Tips When copying finishes The confirmation screen appears. Press [OK] to finish copying. Delete Navigator [RAM] [SD] [USB] Important: Once deleted, contents cannot be recovered. DRIVE SELECT to select the drive (DVD, SD or USB). To view other pages Press [, , , ] to select “Previous” or “Next”, then press [OK]. – You can also press [, ] to view other pages. Multiple editing Select with [, , , ], then press [PAUSE]. (Repeat.) – A checkmark appears.
Setting DVD On-Screen Menus Accessing the DVD On-Screen Menus [DVD] When playing discs, disc settings can be displayed and changed. Menu options will differ based on disc type and contents. DRIVE SELECT to select the DVD drive. DISPLAY B Subtitle [RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] [-RW‹VR›] (Only disc that contain subtitle on/off information) Turn the subtitle on/off. Subtitle on/off information cannot be recorded using this unit.
Other Menu [RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] [DVD-V] [-RW‹VR›] and DivX Picture [RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] [DVD-V] [-RW‹VR›] Set picture mode Normal: Default setting Cinema: Mellows down movies, enhances detail in dark scenes. DNR (Digital Noise Reduction) [RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] [DVD-V] [-RW‹VR›] and DivX “On” reduces noise and picture degradation.
DVD and Card Management Accessing the Management Menus Preparation: [RAM] [SD] Release protection (disc, cartridge, card right). Insert a disc or card. Naming Discs [RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] Perform preparation steps 1−4 of “Accessing the Management Menus” ( left). , select “Disc Name”, then OK DRIVE SELECT to select the drive (DVD or –You can give a name for the disc ( 42). SD). Tips With the unit stopped The disc name is displayed in the DVD MANAGEMENT window.
Deleting All Recordings Formatting Discs or Cards Important: Once deleted, contents cannot be recovered. [RAM] Perform preparation steps 1−4 of “Accessing the Management Menus” ( 52). , to select “Delete All Recordings” then OK to select “Yes” then to select “Start” then Important: Once formatted, contents cannot be recovered. [RAM[ [-RW‹V›] [+RW] [-RW‹VR›] [SD] Perform preparation steps 1−4 of “Accessing the Management Menus” ( 52).
DVD and Card Management Selecting Whether to Show the Top Menu First [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] Before finalizing a disc, select whether to show the Top Menu after finalizing. Perform preparation steps 1−4 of “Accessing the Management Menus” ( 52). , to select “Playback will start with:”, then OK , to select desired item, then Notes Do not disconnect the AC power supply cord while finalizing. This can render the disc unusable.
Setup Menus “Accessing the Setup Menu” You will have to perform the following 3 steps for all other operations on page 55−66. Set Channels Manually The captions you select or modify are used as channel names and displayed on the Direct Navigator screen. Perform steps 1−3 of “Accessing the Setup Menu” ( With the unit stopped left). , to select “Channel”, then , to select “Other Functions”, then OK , to select “Set Channels Manually”, then OK , to select channel.
Setup Menus Selecting the caption After selecting a channel ( 55, step 6, “Set Channels Manually”). , to select the “Caption” column. , to select “All” or “Favorite”, then OK [All] To select a channel from all of the channels set. [Favorite] To select a channel from favorite channels. Parental Rating , to select the caption. – After selecting the “Channel” column with [, ], repeat steps 6–8 to set other channels.
11 Select how long the unit remains on when it is not being used. Perform steps 1−3 of “Accessing the Setup Menu” ( 55). Enter a 4-digit password with the numbered buttons, then OK – A screen appears confirming that you have set a password. Press [OK]. If you select “Off” for “Set”: A screen appears confirming that you haven’t set a rating. Press [OK]. To change the password After selecting “Parental Rating” ( 56, step 5).
Setup Menus Set Clock Automatically After selecting “Clock Settings” ( OK 57, step 5). , to select “Set Clock Automatically”, then OK to confirm new date and time and to initiate the clock. Set the time change dates for DST Set the beginning and end dates for DST. ( to start auto setting. OK The following screen appears when the setting is complete. Set Clock Automatically Clock Setting completed successfully. 13).
Audio Language Restore Default Settings This returns Setup menus to default settings, except for the clock, channel settings, ratings level, closed caption, and onscreen language. Perform steps 1−3 of “Accessing the Setup Menu” ( 55). After selecting “Settings for Playback” ( left, step 5).
Setup Menus Settings for Recording Recording Time in EP Mode Select the maximum number of hours for recording in EP mode. Perform steps 1−3 of “Accessing the Setup Menu” ( 55). , to select “Video”, then , to select “Black Level Control”, then OK , to select “Disc”, then Input Level , to select “Settings for Recording”, then OK Adjusts the black level of the input signal. After selecting “Black Level Control” ( above, step 5).
PCM Down Conversion Multi-channel TV Sound (Analog) [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] Select whether to record the main or secondary audio program (SAP) when recording to these discs. (You cannot select the audio type on the unit when recording audio from an external device. Select it on the external device.) Perform steps 1−3 of “Accessing the Setup Menu” ( 55). Select how to output audio with a sampling frequency of 96 kHz or 88.2 kHz. Signals are converted to 48 kHz or 44.
Setup Menus DTS Status Messages Choose whether to output by “Bitstream”, which processes DTS signals on other connected equipment, or to convert the signals to “PCM” (2ch) on the unit before output. Choose whether to show status messages automatically or not. Perform steps 1−3 of “Accessing the Setup Menu” ( 55). , to select “Display”, then After selecting “Digital Audio Output” ( 61, step 5).
Digital (Closed Caption) settings Front Display Changes the brightness of the unit’s display. After selecting “On” ( Perform steps 1−3 of “Accessing the Setup Menu” ( left, step 7). 55). , to select “Display”, then , to select “Front Display”, then OK , to select “Bright”, “Dim” or “Automatic”, then OK [Automatic] The display turns dark during playback. When the unit is turned off, the unit’s display disappears. While using this mode the standby power consumption can be reduced.
Setup Menus TV Aspect 4:3 TV settings for DVD-RAM This setting allows you to select the type of television connected. Perform steps 1−3 of “Accessing the Setup Menu” ( 55). You can select how to display the image on the TV when you watch 16:9 images (DVD-RAM) on a 4:3 standard aspect TV. Perform steps 1−3 of “Accessing the Setup Menu” ( 55).
24p Output for DVD-Video Functions of HDMI Perform steps 1−3 of “Accessing the Setup Menu” ( 55). , to select “TV Screen”, then When this unit is connected to a TV supporting 1080/24p output via an HDMI cable, this unit displays each frame at 1/24 second intervals – the same interval originally shot with the film camera. After selecting “Functions of HDMI” ( left, step 5). , to select “24p Output for DVD-Video”, then OK , to select “Functions of HDMI”, then OK HDMI Priority above, step 5).
Setup Menus HDMI RGB Output Range Select Tape Length Effective when connected to a device that only supports RGB output. After selecting “Functions of HDMI” ( 65, step 5). Set the length of tape you are using so the unit can show the correct remaining time. Perform steps 1−3 of “Accessing the Setup Menu” ( , to select “HDMI RGB Output Range”, then OK 55).
Parental Rating List U.S. TV Rating (U.S. TV Programs Ratings) TV-NR TV-Y TV-Y7 TV-G TV-PG TV-14 TV-MA [Viewable] [Blocked] [Viewable] [Blocked] [FV Blocked] [Viewable] [Blocked] [Viewable] [Blocked] [--]: Viewable [X]: Blocked D, L, S, V (all selected) Any combination of D, L, S, V [--]: Viewable [X]: Blocked D, L, S, V (all selected) Any combination of D, L, S, V [--]: Viewable [X]: Blocked L, S, V (all selected) Any combination of L, S, V [FV]: Fantasy/Cartoon Violence Not Rated.
Other Settings Remote Control Codes for the TV Using the Unit’s Remote Control to Operate the TV and the Set Top Box (Cable Box, Satellite Receiver, etc.
Manufacturer Sva Sylvania Symphonic Syntax-Brillian Tatung Thomson Toshiba Ultra Viewsonic Westinghouse Yamaha Zenith Code 0587 / 0748 / 0768 / 0865 / 0870 / 0871 / 0872 0020 / 0028 / 0030 / 0054 / 0065 / 0096 / 0171 / 0381 0171 / 0180 1007 / 1144 / 1240 / 1255 / 1257 / 1258 / 1331 0003 / 0049 / 0055 / 0396 / 1101 / 1756 0209 / 0210 / 0047 0036 / 0060 / 0149 / 0154 / 0156 / 0650 / 0832 / 0845 / 1156 / 1164 / 1256 / 1265 / 1356 / 1656 / 1704 0391 0857 / 0864 / 0885 / 1755 0885 / 0889 / 0890 / 1282 / 1577 0
Connection Options for Improved Playback Quality You can enjoy a high-quality picture by using the following terminals for connection. Standard Quality Picture Highquality Picture VIDEO terminal S VIDEO terminal HDMI terminal COMPONENT VIDEO terminal DVD output and DVD/VHS output The unit has DVD/VHS common output terminals and DVD priority output terminals. DVD/VHS common output Both DVD and VHS signals can be output.
Using Component Video Cables for Better Video (Component Video Cables not included) The COMPONENT VIDEO OUT terminals on this unit can be used for either interlace or progressive output ( to provide a purer picture than the S VIDEO OUT terminal.
Connection Options for Improved Playback Quality You can enjoy better quality sound by changing the audio cable connection between this unit and your TV on page 8 to 10 as follows. Using an Audio Cable for Better Sound (Audio Cable not included) Use this connection to play sound through speakers connected to an amplifier or system component.
SD Card and USB Memory Information USB memories you can use with this unit Standard symbol Type USB memory [USB] File format Playing Copying Instructions MP3 You can play MP3 files recorded onto the USB memory using a computer. ( 33) Still pictures (JPEG) You can play and copy still pictures taken on a digital camera etc. ( 34, 48) –You can copy still pictures to/from DVD-RAM discs only. –You can copy albums only.
Disc Information Usable Discs for Recording and Playback Rewritable Finalization Needed1 Recording 16:9 aspect picture2 Recording broadcasts that allow one copy (CPRM) ( 23) — [RAM] — — (4:3 aspect) — [-R] before finalization [DVD-V] after finalization — — (4:3 aspect) — [-R]DL] before finalization [DVD-V] after finalization — (4:3 aspect) — [-RW‹V›] before finalization [DVD-V] after finalization +R — — (4:3 aspect) — [+R] before finalization [DVD-V] after fina
Play-only Discs Disc type Standard symbol Discs that Cannot be Played Uses DVD-Video [DVD-V] DVD-RW (DVD Video Recording format) High quality movie and music discs [-RW‹VR›] DVD-RW video recorded on another DVD recorder You can play programs that allow “One time only recording” if they have been recorded to a CPRM compatible disc. By formatting ( 53) the disc, you can record to it in DVD-Video format. It may be necessary to finalize the disc on the equipment used for recording.
MP3s, DivXs and Still Pictures (JPEG) MP3 File Information Playable media [-R] [-R]DL] [CD] [USB] File format MP3 Files must have the extension “.mp3” or “.MP3”. Number of Maximum number of folders (groups) folders (groups) recognizable: 99 folders (groups) (including the root folder) Number of files (tracks) Bit rates Sampling frequency ID3 tags Maximum number of files (tracks) recognizable: 999 files (tracks) (Total number for all the MP3, JPEG and other type of files.) 32 kbps to 320 kbps 16 kHz/22.
Frequently Asked Questions Page Setup What equipment is necessary to play multi-channel surround sound? You cannot play back multi-channel sound on this unit without other equipment. You must connect this unit with an HDMI cable or an optical digital audio cable to an amplifier with a built-in Dolby Digital or DTS decoder. 72 Can the headphones and speakers be directly connected to the unit? You cannot directly connect to the unit. Connect through the amplifier, TV, etc.
Frequently Asked Questions Page Recording Can I record from a commercially purchased video cassette or DVD? Most commercially sold video cassettes and DVDs are copy protected; therefore, recording is usually not possible. − Can DVD-R, DVD-R DL, DVD-RW (DVD-Video format), +R, +R DL, and +RW recorded on the unit be played on other equipment? You can play these discs on compatible equipment such as DVD players after finalizing the disc on this unit. 54 [+RW] It is not necessary to finalize.
Error Messages On the Unit’s Display Page An error has occurred. The number following “H” or “F” depends on the status of the unit. Check the items below and in the Troubleshooting Guide. If the service number still does not disappear after the check, reset the unit ( 81, “To restore the unit if it freezes”). − If the service numbers fail to clear, note the service numbers and contact a qualified service person. − The remote control and the main unit are using different codes.
Error Messages Page On the TV 36 Authorization Error. This unit is not authorized to play this recording. You are trying to play the DivX VOD content that was purchased with a different registration code. You cannot play the content on this unit. (DivX) Cannot finish recording completely. The program was copy-protected. − The disc may be full. − There are already 99 recordings ([+R] [+R]DL] [+RW] 49 recordings). − Cannot play.
Troubleshooting Guide If the Antenna Connector doesn’t Match Use the following connection to suit the antenna lead to the unit’s RF IN terminal, and the 75 coaxial cable to the antenna terminals on your TV or other equipment. Refer to the other equipment’s operating instructions for more information.
Troubleshooting Guide Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the chart do not solve the problem, refer to “Customer Services Directory” on page 94 if you reside in the U.S.A., or refer to the “Product information” on page 93 if you reside in Canada. The following does not indicate a problem with the unit: Regular disc rotating sound. Poor reception due to atmospheric conditions.
Operation Page Cannot operate the TV or Set Top Box with the unit’s remote control. Change the manufacturer code on the remote control. 68 Select TV or Set Top Box mode on the remote control. 68 Cannot operate the DVD. Press [DRIVE SELECT] to select the DVD drive when operating DVDs or CDs. – Make sure the TV is on the correct channel or input mode. 17 Cannot operate the VHS. Press [DRIVE SELECT] to select the VHS drive when operating VHS cassettes.
Troubleshooting Guide General Issues VIERA Link VIERA Link doesn’t work General Issues Check the HDMI cable connection. Check that “HDMI” is displayed on the front display when the power for the main unit is set to “On”. − Make sure that “VIERA Link” is set to “On”. 66 Check the “HDAVI Control” settings on the connected device.
Playback Issues Picture TV reception worsens after connecting the unit. This can occur because the signals are being divided between the unit and other equipment. It can be solved by using a signal booster, available from electronics retailers. The images from the unit do not appear on the TV. Picture is distorted. Make sure recorder is connected to an appropriate AV input of the TV. Page − 8 to 11 Make sure the TV’s input setting (e.g., VIDEO 1) is correct.
Troubleshooting Guide Playback Issues No sound. Low volume. Distorted sound. Cannot hear the desired audio type. Sound Check the connections and the “Digital Audio Output” settings. Check the input mode on the amplifier if you have connected one. 61, 72 Check if TV is muted. − Check if amplifier is muted. − Press [AUDIO] to select the audio. Cannot switch audio. Page 31, 38 Sound is not output while fast-forwarding during chasing playback and simultaneous record and playback.
Operation Play fails to start even when [ PLAY] is pressed. Play starts but then stops immediately. Insert the disc correctly with the label facing up. Ensure disc is for the correct DVD-Video region number, and is not defective. The disc is dirty. You tried to play a blank disc or a disc that is unplayable on the unit. Audio and video momentarily pause.
Troubleshooting Guide Playback Issues VHS Page On-screen display indicators for video cassette playback do not appear. Select “Automatic” in “Status Messages” in the Setup menu. – Press [STATUS] to show the on-screen display indicators for video cassette playback. – The on-screen indicator for video cassette playback will not be displayed when this unit is connected to the TV with the DVD PRIORITY output terminals or HDMI AV OUT terminal. The gray background appears during playback.
Recording Issues DVD Recording/Scheduled Recording/Copying/External Input (continued) Page Recording does not stop even when [ STOP] is pressed. If you start recording immediately after turning on the unit while “Quick Start” is set to “On”, you cannot stop recording for a few seconds. 58 Scheduled recording does not work properly. The scheduled recording program is incorrect or different scheduled recording times overlap. Correct the program. 27 The clock is not correct. Set the clock.
Troubleshooting Guide Recording Issues VHS Recording Page “ ” flashes when I try to start recording. A video cassette is not inserted. Insert a video cassette with an accidental erasure prevention tab. 15 Cannot record. The accidental erasure prevention tab has been removed. Cover the hole with adhesive tape. 15 Cannot record a TV program. Digital broadcasts cannot be recorded to video tape. − Editing Issues DVD & SD Page The disc is dirty. Wipe with a damp cloth and then wipe dry.
Glossary Bitstream HDMI (High-Definition Multimedia Interface) This is a signal compressed and converted into digital form. It is converted back to a multi-channel audio signal, e.g., 5.1-channel, by a decoder. Unlike conventional connections, it transmits uncompressed digital video and audio signals on a single cable. This unit supports highdefinition video output (720p, 1080i and 1080p) from HDMI AV OUT terminal. To enjoy high-definition video a high definition compatible television is required.
Specifications Power supply: Power consumption: Standby mode: (Shipping Condition) (User Setting: Quick Start: ON) AC 120 V, 60 Hz Approx. 40 W Approx. 3.5 W Approx. 17.6 W Recordable discs: DVD-RAM: 2X SPEED (Ver. 2.0) 2−3X SPEED (Ver. 2.1) 2−5X SPEED (Ver. 2.2) DVD-R (SL): 1X SPEED (Ver. 2.0) 1−4X SPEED (Ver. 2.0) 1−8X SPEED (Ver. 2.0) 1−16X SPEED (Ver. 2.1) DVD-R (DL): 2−4X SPEED (Ver. 3.0) 2−8X SPEED (Ver. 3.0) DVD-RW: 1X SPEED (Ver. 1.1) 1−2X SPEED (Ver. 1.1) 2−4X SPEED (Ver. 1.2) 2−6X SPEED (Ver. 1.
Product Service 1. Damage requiring service−The unit should be serviced by qualified service personnel if: (a) The AC power supply cord or AC adaptor has been damaged; or (b) Objects or liquids have gotten into the unit; or (c) The unit has been exposed to rain; or (d) The unit does not operate normally or exhibits a marked change in performance; or (e) The unit has been dropped or the cabinet damaged. 2. Servicing−Do not attempt to service the unit beyond that described in these operating instructions.
Limited Warranty (ONLY FOR U.S.A.) Panasonic Consumer Electronics Company, Division of Panasonic Corporation of North America One Panasonic Way Secaucus, New Jersey 07094 Panasonic Puerto Rico, Inc. Ave. 65 de Infantería, Km. 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985 Panasonic DVD Recorder Limited Warranty Limited Warranty Coverage If your product does not work properly because of a defect in materials or workmanship, Panasonic Consumer Electronics Company or Panasonic Puerto Rico, Inc.
Limited Warranty (ONLY FOR CANADA) Panasonic Canada Inc. PANASONIC PRODUCTLIMITED WARRANTY Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship and agrees to remedy any such defect for a period as stated below from the date of original purchase.
Referencia rápida en español (Spanish Quick Reference) Conexión básica Ajuste de los canales y el reloj Nota: Puede que los terminales en el panel trasero de su TV no sean similares a como se ilustran a continuación. Por favor consulte las etiquetas de los terminales con atención para asegurar conexiones correctas.
TRACKING/V-LOCK , para seleccionar el “Antena” o “Cable”, luego CH OK para seleccionar el canal deseado. También puede seleccionar canales con los botones numéricos. OK para iniciar el ajuste automático de canales/reloj. Confirmar la hora, luego OK –HL (horario de verano) muestra el ajuste para el horario de verano. –Huso h. (zona horaria) muestra la diferencia de hora con la hora del Meridiano de Greenwich (GMT). Ajuste automático del reloj Ajuste del reloj automático terminado.
Referencia rápida en español (Spanish Quick Reference) Grabación de programas de televisión [RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] [VHS] Las emisiones digitales no pueden ser grabadas en cintas de video. Preparación: [RAM] Si el disco está protegido, libere la protección. [VHS] Asegúrese de que la pestaña contra borradura accidental esté intacta. Use un disco o casete VHS con suficiente espacio en blanco disponible. DVD/VHS POWER DRIVE SELECT para encender el aparato.
Copiar Copiar (VHS DVD) Borrado de grabaciones con el navegador de borrado (BORRAR Navegador) Importante: Una vez borrados, los contenidos no podrán recuperarse. [VHS] [RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] Preparación: [RAM] Si el disco está protegido, libere la protección. Inserte un disco con suficiente espacio en blanco disponible. Seleccione el modo de grabación de DVD. Inserte la cinta VHS que contenga el programa a ser copiado.
Index Angle .................................................... 50 Audio attributes............................................ 50 language............................................ 59 receiving, recording ..................... 25, 61 Auto Bilingual Selection ..................... 38 Auto Mode ............................................ 24 Change Thumbnail .............................. 44 Channel adding, deleting ................................. 55 audio............................................
