Operating instructions

80
VQT2J51
Messages
§
The message are alternately displayed.
On the Unit’s Display
H∑∑, F∑∑
(“∑” stands for a service number.)
≥ An error has occurred. The number following “H” or “F” depends on the status
of the unit. Check the items below and in the Troubleshooting Guide. If the
service number still does not disappear after the check, reset the unit (> 82, To
restore the unit if it freezes).
≥ If the service numbers fail to clear, note the service numbers and contact a
qualified service person.
DVD ∑
(“∑” stands for a number.)
≥ The remote control and the main unit are using different codes. Change the
code on the remote control. (> 82)
GUIDE ≥ GUIDE Plus+ data is being downloaded. (> 73)
HARD ERR
§
≥ If there is no change after turning the unit on and off, consult the dealer where
the unit was purchased.
NoCASSETTE
§
≥ You have not inserted a video cassette for the recording. (> 7)
NoERAS ≥ You cannot delete items on this disc.
≥ The disc may be damaged. Use a new disc.
NoREAD ≥ The disc is dirty or badly scratched. The unit cannot record, play, or edit. (> 7)
≥ The disc may be incompatible or of poor quality. (> 15, 16)
≥ You have used a lens cleaner and it has finished operation. Press [< OPEN/
CLOSE] on the main unit to eject the disc. (> 6)
NoWRIT ≥ You cannot write to this disc.
The disc may be damaged. Use a new disc.
FINAL ≥ When the screen asking if you want to finalise the disc appears, the message is
displayed. (> 29)
PLEASE WAIT
§
≥ Displayed when the unit is started. This is not a malfunction.
≥ The unit is carrying out its recovery process. You cannot operate the unit while
the message is displayed.
PROG FULL
§
≥ There are already 16 timer recording programmes. Delete unnecessary timer
recording programmes. (> 34)
PROTECT
§
≥ You have inserted a video cassette without the accidental erasure prevention
tab. Use a video cassette with an accidental erasure prevention tab. (> 7)
REMOVE ≥ The USB device is drawing too much power. Remove the USB device and turn
the unit off.
SW-DL ≥ The unit is performing a software update. (> 73)
SP 35:50, LP 151h
“SP”, “LP” and the numbers are examples.
≥ Available space on the disc.
The example “SP 35:50” is displayed when less than 100 hours are available
and the example “LP 151h” is displayed when over 100 hours are available.
“SP” and “LP” are recording modes, “35:50” means “35 hours 50 minutes” and
“151h” means “151 hours”.
UNSUPPORT
§
≥ You have inserted a disc the unit cannot play or record onto. (> 15, 16)
≥ You tried to operate with a non-compatible USB memory. (> 17)
UNFORMAT
§
≥ You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL
or DVD-RW (DVD-Video format) that has been recorded on other equipment.
Format the disc to use it.
However all the recorded contents on the disc are deleted. (> 29)
EXT-L ≥ This unit is in EXT LINK standby. EXT LINK has been turned on and will stop
operation on the unit until the recording has completed.
Press [EXT LINK] to stop recording or cancel linked timer. (> 31)
DMR-EZ49VEB_VQT2J51.book 80 ページ ２００９年１２月２１日 月曜日 午後５時４０分