Complete Operating Instruction manual

33
Timer recording (continued)
Manual programming
[RAM] [DVD-R]
Remote control only
You can set your own programming conditions (up to 16
programmes).
Preparation
≥
Switch [DVD, TV] (15) to “DVD”.
≥
Ensure that this unit’s clock is set correctly.
≥
Insert a disc for recording (make sure there is enough room for
the programme you are going to record plus a little extra).
1
Press [PROG/CHECK] (13).
≥
The Timer Programme List screen appears.
A line that is ready for programming is highlighted.
2
Press [ENTER] (10).
≥
The Timer Programme Correction screen appears.
3
Use [1] (10) to move through the items and change
the items with [3, 4] (10).
≥
The current settings are shown each time you press [
1
]
(10).
≥
You may use the numeric buttons (4) to enter “Name”,
“Date”, “Start” and “Stop”.
≥
Name (Programme Position/TV Station Name)
≥
Date
Current date
>
the day before one month later
>
Daily (Sunday to Saturday)
>
Daily (Monday to Saturday)
>
Daily (Monday to Friday)
>
Weekly (Sundays)
>
...
>
Weekly (Saturdays)
≥
Start (start time)/Stop (finish time)
The time increases or decreases in 30-minute increments if
you hold the button.
≥
Mode (Recording mode)
XP
>
SP
>
LP
>
EP
>
FR (page 25)
≥
PDC (For the United Kingdom)
ON
>
OFF (
jjj
) (page 32)
4
Press [ENTER] (10) when you have finished making
changes.
≥
To continue programming:
Repeat steps 2, 3, and 4.
5
Press [PROG/CHECK] (13) or [RETURN] (23).
To put the unit on recording standby
Press [
Á
, TIMER] (12).
Ensure “
Á
” lights on the unit’s display.
To change the timer recording programme
1) While the Timer Programme List Screen is being shown, use
[
3
,
4
] (10) to select the programme you want to change, and
press [ENTER] (10) to show the Timer Programme Correction
screen.
≥
You may also select programme by inputting a 2-digit
number using the numeric buttons (4).
≥
Use [
2
,
1
] (10) to move to the page preceding or following
the one on display.
2) Move through the items with [
1
] (10) and change the settings
with [
3
,
4
] (10) and press [ENTER] (10).
Note
≥
The built-in clock employs 24-hour system.
≥
The remaining time is not shown if you insert discs other than
DVD-RAM or DVD-R.
≥
The remaining time displayed is calculated based on the current
recording mode.
≥
If the disc is protected (pages 37, 73), the unit switches to
standby but does not go on standby for recording. Check the disc
carefully.
≥
Recording is not possible unless you set “Disc Protection“ in
“DISC INFORMATION“ to “Off“ (page 37).
≥
You cannot record to a disc if the write protect tab on a cartridge
disc is set to protect. Release this before operation (page 73).
≥
Even if the unit is put in the timer recording standby mode or the
timer recording is being performed, you can play a programme.
≥
If the unit is not put in the timer recording standby mode at the
latest 10 minutes before the programmed timer recording starting
time, the [
Á
] flashes on the unit display. In this case, press the
[
Á
, TIMER] (12) button to put the unit in the timer recording
standby mode.
≥
When recording more than one programme in a row, for DVD-
RAM the first few seconds, and for DVD-R about the first 30
seconds of all programmes from the second one onwards will not
be recorded.
RETURN
SELECT
SP OK 1:221:19BBC 1 16/ 7 TUE01
Mode
Disc
space
StopStartNo. Name Date
1:58 SP
TIMER
RECORDING
Remain
1:19:00 16.7 TUE
ENTER
New Timer Programme
CANCEL
OFF
PDC
RETURN
No.
SELECT
1:58 SP
TIMER
RECORDING
Remain
1:55:00 16.7 TUE
ENTER
--
0 9
--:-- --
----------
Mode StopStart Name Date
--:-- --
SP
----
PDC
Please set Channel.
---
1:58 SP
TIMER
RECORDING
Remain
1:19:00 16.7 TUE
2:00
16/ 7 TUE
Mode StopStart Name Date
SP
BBC 1
1:00
PDC
OFF
B.book 33 ページ ２００２年８月５日 月曜日 午後１時１０分