Operating Instructions

67
RQT9118
Reference
General Issues Operation (Continued)
Page
“U88” is displayed and the disc
cannot be ejected.
The unit is carrying out the recovery process. The disc may be defective. Do
the following to eject the disc. Try another disc.
(1) Press [
8
] on the main unit to switch to standby mode.
If the unit doesn’t switch to standby mode, reset the unit (➔ 65, “To restore
the unit if it freezes”).
(2) While the unit is turned off, press and hold [
g
] and [CH
1
] on the main
unit at the same time for about 5 seconds. (Ejection may take extra time
depending on discs.)
• −
Cannot eject a disc. The unit is recording.
The unit may have a problem. Eject the disc as in (2) above.
Linked timer recordings with external equipment is in recording standby (“EXT-
L” on the unit’s display blinks when [
^
DVD] is pressed). Press [EXT LINK] to
cancel the recording standby.
If the Child Lock function is activated, above operation does not work. Cancel
the Child Lock function.
•
•
•
−
−
25, 57
Startup is slow. Startup takes time in the following situations:
A disc other than a DVD-RAM is inserted.
The clock is not set.
Immediately after a power failure or the AC mains lead is connected.
When the unit is connected with an HDMI cable.
When “Power Save” is set to “Off”, startup becomes faster than when “Power
Save” is “On”.
•
–
–
–
–
•
−
56
General Issues VIERA Link
Page
VIERA Link doesn’t work. Check the HDMI cable connection. Check that “HDMI” is displayed on the front
display when the power for the main unit is set to On.
Make sure that “VIERA Link” is set to “On”.
Check the “HDAVI Control” settings on the connected device.
Some functions may not work depending on the version of “HDAVI Control” of
the connected equipment. This unit supports “HDAVI Control 3” functions.
If the connection for the equipment connected with an HDMI cable was
changed, or if there was a power failure or the plug was removed from the
household mains socket, “HDAVI Control” may not work. In this case, perform
the following operations.
1. When the HDMI cable is connected to all equipment with the power on,
turn the TV (VIERA) on again.
2. Change the TV (VIERA) settings for the “HDAVI Control” function to off,
and then set to on again. (For more information, see the VIERA operating
instructions.)
3. Switch the VIERA input to HDMI connection with this unit, and after this
unit’s screen is displayed, check that “HDAVI Control” is working.
•
•
•
•
•
−
55
−
−
−
The control panel does not appear. The control panel is only displayed when connected to a TV with “HDAVI
Control 2” or “HDAVI Control 3” function.
•
39
General Issues DVB-T
Page
Digital broadcasts cannot be
received.
Check the connections.
Digital broadcast may not have started in your region yet.
The aerial may not be pointing in the direction of the TV station, or the
direction of the aerial may have changed due to strong winds or vibration. If
problem persists consult your local TV aerial installer.
Perform “Auto-Setup Restart” in the Setup menu.
•
•
•
•
8, 9, 58
−
−
51
TV reception worsens after
connecting the unit.
This can occur because the signals are being divided between the unit and
other equipment. It can be solved by using a signal booster, available from
electronics retailers.
• −
After DVB Auto-Setup only some
or no DVB channels are found.
Check to ensure your area is covered by DVB transmissions.
Check that the aerial and antenna cable are designed for DVB.
Use the supplied RF coaxial cable shown in STEP 2, Basic Connection.
If you live within 5-10 km of DVB transmission towers, a combined VHF/UHF
aerial should be adequate. Outside this area, separate VHF and UHF aerials
provide superior reception performance.
Perform “Auto-Setup Restart” in the Setup menu.
•
•
•
−
8, 9
51
DMR-EZ28-EB _RQT9118-B.indb 67DMR-EZ28-EB _RQT9118-B.indb 67 2008/04/04 10:32:352008/04/04 10:32:35