User manual

ManualsBrandsPANASONIC ManualsSensorsPressure sensor -1 bar up to 1 bar Cable, open end

INSTRUCTION MANUAL

DP-100 Series

High-performance Digital Display

Pressure Sensor

WARNING

Thank you very much for using SUNX products. Please read this

Instruction Manual carefully and thoroughly for the correct and optimum

use of this product. Kindly keep this manual in a convenient place for quick

reference.

Never use this product as a sensing device for personnel protection.

In case of using sensing devices for personnel protection, use products

which meet laws and standards, such as OSHA, ANSI or IEC etc., for

personnel protection applicable in each region or country.

Japanese Measurement Laws prohibit the use of this product in Japan.

NAMES OF EACH PART

Connection

connector

DP-100

type: R

㧛

+ M5 female screw

DP-100-E

type: G

㧛

+ M5 female screw

DP-100-N

type:

NPT

㧛

+ M5 female screw

Pressure port

㧝

DP-100

Main display

Sub-display

Setting value

DOWN key

Setting value UP key

٨ When connecting a commercial coupler to the pressure port, attach a

12mm spanner (14mm for DP-100-E type) to the pressure port's hexa-

gon section to fix the port, and then tighten with a tightening torque of

9.8N䊶m or less. The commercial coupler or pressure port section will be

damaged if the tightening torque is excessive.

Wrap sealing tape around the coupler when connecting to prevent leaks.

PIPING

Standard type:

Lights up when compa-

rative

output 2 is ON

High-function type:

Lights up when analog

voltage output is set

Output 2 / analog

voltage output oper-

ation indicator

Lights up when compa-

rative output 1 is ON

Output 1 operation

indicator

Mode selection key

MJE-DP100 No.6091-00

12mm spanner

MOUNTING

٨ The sensor mounting bracket (MS-DP1-1) is available as an option.

When mounting the sensor onto the sensor mounting bracket, etc., the

tightening torque should be 1.2N䊶m or less.

Sensor mounting bracket

MS-DP1-1 (Optional)

M3 (length 6mm) screws

with washers

(Accessory with MS-DP1-1)

٨ The panel mounting bracket MS-DP1-2 (optional) and front cover

MS-DP1-3 (optional) are also available as options.

Front cover

MS-DP1-3 (Optional)

(Unit: mm)

Panel cut-out size

Panel mounting bracket

MS-DP1-2 (Optional)

M3 (length 12mm) pan head

screw

(Accessory with MS-DP1-2)

For use outside Japan

Connection method

Disconnection method

Note: Do not pull by holding the cable without pressing the release lever, as this can

cause cable break.

Insert the cable with connector CN-14A-Cغ

into this product's connection connector

section as shown in the right figure.

٨ Pressing the release lever of the cable

with connector, pull out thecable.

WIRING

Cable with connector

CN-14A-Cغ

Release lever

Ԙԙ Ԛԛ

㧝

Connector pin No.

Terminal name

+VԘ

Comparative output 1ԙ

Standard type: Comparative output 2

High-function type: Analog voltage output or external input

0Vԛ

Contact: SPHD-001T-P0.5

Housing: PAP-04V-S

[JST Mfg. Co., Ltd.]

Standard type

Users' circuitInternal circuit

12 to 24V DC

±10%

(Black)

Comparative output 1

Main circuit

(White) Comparative output 2

(Blue) 0V

100mA max.

Load

Main circuit

High-function type

Users' circuitInternal circuit

12 to 24V DC

±10%

(White)

Analog voltage output

or external input

(Black) Comparative output 1

(Blue) 0V

100mA max.

1kΩ

Load

PNP output type

Standard type

Main circuit

Users' circuitInternal circuit

12 to 24V DC

±10%

(Black) Comparative output 1

(White) Comparative output 2

(Blue) 0V

100mA max.

Load

NPN output type

When using the analog voltage output, take care to the input impedance of

the connected device.

Furthermore, note that if the cable is extended, the cable resistance will

cause the voltage to drop.

I/O CIRCUIT DIAGRAMS

High-function type

Main circuit

(Black) Comparative output 1

Users' circuitInternal circuit

12 to 24V DC

±10%

(Blue) 0V

(White)

Analog voltage output

or external input

1kΩ

100mA max.

Load

(Brown)㧗V

Color code of cable with connector

(Brown)㧗V

Color code of cable with connector

(Brown)㧗V

Color code of cable with connector

(Brown)㧗V

Color code of cable with connector

Summary of content (5 pages)

PAGE 1
4 WIRING Connection method INSTRUCTION MANUAL Pressure Sensor High-performance Digital Display DP-100 Series For use outside Japan MJE-DP100 No.6091-00 Thank you very much for using SUNX products. Please read this Instruction Manual carefully and thoroughly for the correct and optimum use of this product. Kindly keep this manual in a convenient place for quick reference.
PAGE 2
6 OUTPUT MODE AND OUTPUT OPERATION 8 RUN MODE ٨ The EASY mode, hysteresis mode or window comparator mode can be selected as the output mode for comparative output 1 and comparative output 2. Refer to 'Comparative output 1/2 output mode setting' in ' 9 MENU SETTING MODE' for details. Setting the threshold value EASY mode Pressure ٨ Refer to 'Comparative output 1/2 output mode setting' and 'Analog voltage output / external input selection' in ' 9 MENU SETTING MODE' for setting conditions.
PAGE 3
࡮High-function type 9 MENU SETTING MODE Comparative output 1 output mode: ' ' (EASY mode) Analog voltage output / external input selection: ' ' (Analog voltage output) ٨ When the mode selection key is held down for two seconds in the RUN mode, the menu setting mode will open. ٨ The mode will change to the RUN mode when the mode selection key is held down during this setting process. ٨ The leftmost setting items are the default settings (factory settings).
PAGE 4
List of code settings ٨ When the mode selection key is held down for four seconds in the RUN mode, the PRO mode will open. ٨ The mode will change to the RUN mode when the mode selection key is held down during this setting process. In this case, the changed item is entered. ٨ The leftmost settings are the default settings (factory setting). MODE Second digit Code 10 PRO MODE Hold down for four seconds When ' ' is set. When ' MODE ' is set.
PAGE 5
12 AUTO-REFERENCE FUNCTION (ONLY HIGH-FUNCTION TYPE) 14 MAIN SPECIFICATIONS ٨ The auto-reference function corrects the setting value using the detected pressure value during Auto-reference input ON auto-reference input as Ԙ' = Ԙ 㧗 P-A the reference pressure. Output Pressure ԙ' = ԙ 㧗 P-A ٨ Using the setting value P-A fluctuation OFF as a reference, the setting value is automatically correct- Atmospheric pressure P-A Ԙ' ԙ' ed to 'setting value + P-A'.