User manual

ManualsBrandsPANASONIC ManualsSensorsPressure sensor -1 bar up to 1 bar Cable, open end

MEUML-DP100 V1.1

Thank you for purchasing products from Panasonic Electric Works SUNX

Co., Ltd. Please read this Instruction Manual carefully and thoroughly for

the correct and optimum use of this product. Kindly keep this manual in a

convenient place for quick reference.

 This product has been developed / produced for industrial use only.

 Use within the rated pressure range.

 Do not apply pressure exceeding the pressure resistance value. The

diaphragm will be damaged resulting in faulty operation.

 Make sure that the power supply is off while wiring.

 Incorrect wiring will damage the sensor.

 Verify that the supply voltage including the ripple is within the rating.

 If power is supplied from a commercial switching regulator, ensure that

the frame ground (F.G.) terminal of the power supply is connected to an

actual ground.

 In case noise generating equipment (switching regulator, inverter motor,

etc.) is used in the vicinity of this sensor, connect the frame ground (F.G.)

terminal of the equipment to an actual ground.

 Do not use during the initial transient time (0.5s) after the power supply is

switched on.

 Do not run the wires together with high-voltage lines or power lines or put

them in the same raceway. This can cause malfunction due to induction.

 The specification may not be satisfied in a strong magnetic field.

 Avoid dust, dirt, and steam.

 Take care that the sensor does not come in direct contact with water, oil,

grease, or organic solvents such as thinners, etc.

 Do not insert wires, etc., into the pressure port. The diaphragm will be

damaged resulting in faulty operation.

 Do not operate the keys with pointed or sharp objects.

 Do not apply stress directly to the sensor cable joint by forcibly bending

or pulling.

Use a 12mm end wrench (14mm for DP-100-E type) when tightening a

commercial coupler to the pressure port. The tightening torque should be

9.8N·m or less (M5 female connector: 1N·m or less). The commercial

coupler or pressure port section will be damaged if the tightening torque is

excessive.

Wrap sealing tape around the coupler when connecting to prevent leaks.

INSTRUCTION MANUAL

WARNING

• Never use this product as a sensing device for personnel protection.

• In case of using sensing devices for personnel protection, use

products which meet laws and standards, such as OSHA, ANSI or

IEC etc., for personnel protection applicable in each region or

country.

• DP-100 series is designed for use with non-corrosive gas. It cannot

be used for liquid or corrosive gas.

• Japanese Measurement Laws prohibit the use of this product in

Japan.

1 CAUTIONS

2 PART NAMES

No. Part Description

1 Output 1 opera-

tion indicator

Lights up when comparative output 1 is

2 Output 2 / analog

voltage operation

indicator

• Standard type: lights up when

comparative output 2 is ON

• Multifunction type: lights up when

analog voltage output is ON

3 Pressure unit dis-

play

Depending on the model, “MPa” or “kPa”

appears here. If you set another pressure

unit, attach the appropriate label, e.g. psi,

bar, etc.

4 Main display Large 4-character LCD display.

5 Sub-display Small 4-character LCD display.

6 Mode selection

key

For details, see page 3, section 8,

SELECTING MODES.

7 Up key Increases value being set.

8 Down key Decreases value being set.

9 4-pin male con-

nector

See “Pin assignment, 4-pin male connec-

tor” on page 2.

0 Pressure port • DP-100 type: R1/8 + M5 female screw

• DP-100-E type: G1/8 + M5 female

screw

• DP-100-M type: M5 female screw

• DP-100-N type: NPT1/8 + M5 female

screw

3 PIPING

㧝

DP-100

876

12mm end wrench

Pressure Sensor

For use outside Japan

High-performance Digital Display

DP-100 Series

Summary of content (9 pages)

PAGE 1
. 2 PART NAMES INSTRUCTION MANUAL 3 4 DP-100 Pressure Sensor DP-100 Series High-performance Digital Display 1 For use outside Japan 5 2 MEUML-DP100 V1.1 Thank you for purchasing products from Panasonic Electric Works SUNX Co., Ltd. Please read this Instruction Manual carefully and thoroughly for the correct and optimum use of this product. Kindly keep this manual in a convenient place for quick reference. 6 No. 1 CAUTIONS  This product has been developed / produced for industrial use only.
PAGE 2
NPN output type  Standard type 4 MOUNTING  The sensor mounting bracket (MS-DP1-1) is available as an option. Color code of cable with connector When mounting the sensor onto the sensor mounting bracket, etc., the tightening torque should be 0.5N·m or less. (Brown) +V Main circuit (Black) Load Comparative output 1 Load 100mA max. (White) Comparative output 2 + _ 12 to 24V DC ±10% + _ 12 to 24V DC ±10% + _ 12 to 24V DC ±10% + _ 12 to 24V DC ±10% 100mA max.
PAGE 3
Hysteresis mode Setting condition 2 Pressure The comparative output is turned ON or OFF (depending on the N.O./N.C. setting) when the upper or lower threshold is reached and remains ON or OFF until the other threshold is reached. EASY (EASY mode) Comparative output 2 set to: EASY (EASY mode) Hi H (Hysteresis) Automatic Lo 0 ON OFF Comparative output Notes: Comparative output 1 set to: MODE Automatic • H (Hysteresis): 1 digit or more, 2 digits or more when psi is selected as the pressure unit.
PAGE 4
Multifunction type To unlock, simultaneously press MODE + . Press Setting condition 1 MODE + Automatic EASY (EASY mode) Comparative output 1 set to: Analog voltage output / external input: Peak / bottom hold function The peak / bottom hold functions display the peak value and bottom value of the fluctuating pressure. The peak value is displayed on the main display and the bottom value is displayed on the sub-display.
PAGE 5
10 MENU SETTING MODE ࡮࡮࡮࡮࡮ Item Description Comparative output 1 mode setting Sets operation of comparative output 1. Comparative output 2 mode setting (Standard type only) Sets operation of comparative output 2. Analog voltage output / external input (Multifunction type only) Selects analog voltage output, auto-reference input, or remote zero-adjustment input. N.O. / N.C. selection Selects normally open (N.O.) or normally closed (N.C.).
PAGE 6
1 11 PRO MODE ・・・・ Item Description Sub-display selection Selects what is displayed in the sub-display. • OFF: nothing. • Unit: pressure unit selected. • No.**: desired number. • CuSt: desired numbers, letters (as possible), signs. (Max.) Display speed selection Sets the speed of how often the displayed pressure value on the main display is updated. Hysteresis fixed value selection Sets hysteresis for the EASY mode and window comparator mode (8 levels).
PAGE 7
Code table Procedure, cancel copy function 1 While the slave sensor is disconnected, turn on the power of the master sensor. Code 2nd digit 4th digit 3rd digit HighStandard Standard type type only function type C o m p a r a t i v e N.O. / N.C. C o m p a r a t i v e N.O. / N.C. Analog volt. output/ Threshold Main display Display color selection selection output 1 mode output 2 mode based on: color display external input Analog ComparaN.O.
PAGE 8
14 REMOTE ZERO-ADJUSTMENT FUNCTION, MULTIFUNCTION TYPE 16 MODELS, ORDERING INFORMATION DP10 The remote zero-adjustment function forcibly sets the pressure value to “zero” when the external signal is input. The setting value is not corrected when remote zero-adjustment is input. Make sure that the pressure and setting value during remote zero-adjustment do not exceed the pressure range that can be set.
PAGE 9
17 SPECIFICATIONS Standard type Multifunction type Item Low pressure type High pressure type Pressure type Low pressure type High pressure type Gauge pressure Rated pressure range -100 to + 100kPa -0.1 to +1.0MPa -100 to + 100kPa -0.1 to +1.0MPa Set pressure range -100 to + 100kPa -0.1 to +1.0MPa -100 to + 100kPa -0.1 to +1.0MPa Pressure resistance 500kPa 1.5MPa 500kPa 1.