User manual

ManualsBrandsPANASONIC ManualsSensorsPressure sensor 1 pc(s) -1 bar up to 10 bar M12 (4-pin) (L x W x H) 42.5 x 30 x 30 mm

INSTRUCTION MANUAL

High-performance Digital Display Pressure Sensor for IO-Link

DP-100L Series

ME-DP100L No.0061-90V

Thank you very much for purchasing Panasonic products. Read this Instruction Man-

ual carefully and thoroughly for the correct and optimum use of this product. Kindly

keep this manual in a convenient place for quick reference.

WARNING

● Never use this product as a sensing device for personnel protection.

● In case of using sensing devices for personnel protection, use products which

meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel protec-

tion applicable in each region or country.

● This product is designed for use with non-corrosive gas. It cannot be used for liq-

uid or corrosive gas.

● A product intended for use in Japan conforms to the Japanese Measurement Act.

Do not use a product intended for use overseas in Japan.

1 PART DESCRIPTION

Output operation

indicator 1

(Notes: 1)

Output operation

indicator 2

Lights up when com-

parative output is ON

Mode selection key

Unit display

Main display

Sub display

Setting value

DOWN key

Setting value UP key

Connection

connector

Pressure port

M5 female screw

Notes: 1)

During IO-Link

non communication

During IO-Link com-

munication

Function

Lights up when com-

parative output is ON

(Notes 2)

Flashes

Notes: 2) Synchronized with output operation indicator 2

2 PIPING

● To connect a commercial coupler to the pressure port, manually hold the main

unit of the product and install the coupler by tightening it to a tightening torque

of 1N∙m or less. The commercial coupler or pressure port section will be dam-

aged if the tightening torque is excessive.

Wrap sealing tape around the coupler when connecting to prevent leaks.

3 MOUNTING

● The sensor mounting bracket

MS-DP1-1

is available as an option. When mounting the sen-

sor onto the sensor mounting bracket, etc., the tightening torque should be 0.5N·m or less.

M3 (length 6mm) screws

with washers

(Accessory with

MS-DP1-1

)

Sensor mounting bracket

MS-DP1-1

(Optional)

● The panel mounting bracket

MS-DP1-2

(optional) and

MS-DP1-4

(optional), as well

as the front cover

MS-DP1-3

(optional) and

DPX-04

(optional) are also available.

● The type of the front cover is dierent depending on the applied mounting bracket.

Use

MS-DP1-3

for

MS-DP1-2

, and

DPX-04

for

MS-DP1-4

● For mounting of the panel mounting bracket, refer to the Instruction Manual en-

closed with

MS-DP1-2

MS-DP1-4

4 WIRING

Connection method

● Insert the cable with connector (included in

this product) into the connection connector

section of this product as shown in the gure

to the right.

Disconnection method

● Pressing the release lever of the cable with

connector, pull out the connector.

Cable with connector

provided (on the main-unit

connection connector

side)

Release lever

Contact: SPHD-001T-P0.5

Housing: PAP-04V-S

[JST Mfg. Co., Ltd.]

Note: Do not pull by holding the cable without pressing the release lever, as this can cause cable break or connector

break.

1 2 3 4

Connector pin No.

Wiring color/

M12 connector

Terminal

No.

Terminal name

1 Brown / 1 +V

2 Black / 4 IO-Link communication (C/Q)

3 White / 2 Control output (DO)

4 Blue / 3 0V

5 CONNECTION

●

When connected to IO-Link master

This product IO-Link master

(Brown / 1) +V +V

(Black / 4) C/Q C/Q

(White / 2) DO DI

(Blue / 3) 0V 0V

●

When used as general-purpose sensor

(Brown / 1) +V

(Black / 4) C/Q Note

(White / 2) DO

(Blue / 3) 0V

Load

24V DC

±10%

• Recommended

extension cable

Extension cable with connectors

on both ends

XS5W series

[OMRON Corporation]

Terminal No. Terminal name

1 +V

2 Control output (DO)

3 0V

4 IO-Link communication (C/Q) Note

Note: When the product is used as a general-purpose sensor, the IO-Link communication (C/Q) is generated in the

same way as control output (DO)

How to mount M12 connector

If the xed ring loosens, the connector will come o, causing this product to generate

a communication error.

Before use, be sure to check that the xed ring is not loose.

●

Firmly tighten the xed ring by rotating it.

Fixed ring

6 LIST OF FUNCTIONS

Function Setting on main unit

IO-Link communication setting

(Note)

Comparative output mode

setting

Select from EASY mode / Hysteresis mode /

Window comparator mode

Index61_2

Threshold value setting

EASY mode : Threshold value

Hysteresis mode /

Window comparator mode : Lo side

Index60_1

Hysteresis mode /

Window comparator mode : Hi side

Index60_2

Zero-adjust setting Execute / Cancel Index2

Key lock Set / release Index12

Peak / bottom hold

function

Setting Index82_4

Comparative output mode

setting

N.O. / N.C. Index61_1

Response time setting

Select from 10 steps Index66

Displayed color of the main

display selection

Select from 4 modes Index82_1

Pressure unit selection

Select from 2 modes

DP-101□ is xed

Index83

Display setting of Sub-

display selection

Select from 5 modes Index82_2

No. display setting

Index84_1

Custom display setting Index84_2

Display speed selection Select from 3 steps Index82_3

Hysteresis xed value

selection

Select from 8 steps Index61_3

Eco mode setting Select from 3 modes Index80

Setting check code

8 digit indication

Reset setting Execute Index2

Remote zero-adjust

setting

- Index2

Zero-adjust execution

notication

- Index85

Auto-reference setting - Index2

Operating time - Index163

Number of data save

operations

- Index164

Notication Flag Setting - Index168

Notication Event Code - Index169

Note: For the IO-Link communication setting, refer to the attached sheet, “Index List.”(IMJE-DPLINDEX)

7 OUTPUT MODE AND OUTPUT OPERATION

● The EASY mode, hysteresis mode or window comparator mode can be selected as

the output mode for comparative output.

Refer to “

MENU SETTING MODE

” for details.

EASY mode

● ON / OFF of the comparative output is controlled in this mode.

Pressure

OFF

Comparative

output

H (Hysteresis)

H: Hysteresis xed (Note)

Notes: Hysteresis can be xed in 8 steps.

Refer to

in “

PRO MODE

” for setting.

Hysteresis mode

● This mode controls ON / OFF by arbitrarily setting the hysteresis of the compara-

tive output.

Pressure

Comparative

output

H (Hysteresis)

OFF

H: 1digit or more

Note: “ ” or “ ” is displayed on the sub-display.

Summary of content (4 pages)

PAGE 1
INSTRUCTION MANUAL High-performance Digital Display Pressure Sensor for IO-Link DP-100L Series 5 CONNECTION ●● When used as general-purpose sensor (Brown / 1) +V (White / 2) DO ME-DP100L No.0061-90V (Black / 4) C/Q Note Load Load Thank you very much for purchasing Panasonic products. Read this Instruction Manual carefully and thoroughly for the correct and optimum use of this product. Kindly keep this manual in a convenient place for quick reference.
PAGE 2
9 MENU SETTING MODE ●● The mode will change to RUN mode when the mode selection key is held down during this setting process. In doing so, changed items before holding down the mode selection key have been set. Pressure Window comparator mode ●● In this mode, the ON or OFF state of the comparative output is controlled with a pressure in the set range.
PAGE 3
10 PRO MODE Code table ●● The mode will change to RUN mode when the mode selection key is held down during this setting process. However, changed items before holding down the mode selection key have been set. RUN mode ●● Main display (1st digit form left) Code 1st digit 2nd digit Comparative output output mode N.O. / N.C. selection EASY N.O. EASY mode : Threshold value, Hysteresis mode / Window comparator mode : Lo side Hysteresis N.C.
PAGE 4
12 SPECIFICATIONS ●● Model DP-10 1 2 3 - 4 - 5 - 6 1 : 1: Low-pressure type, 2: High-pressure type 2 : Z: For inside of Japan 3 : L3: IO-Link communication type (Baud rate: COM3) 4 : M: M5 female screw 5 : P: PNP output type 6 : None: Discrete wire type, C: M12 connector type Item Type Pressure type Rated pressure range Discrete wire type Low-pressure type -100 to +100kPa Set pressure range -101.0 to +101.