Operating Instructions DVD Recorder Model No. DMR-ES20DEB Panasonic DVD RECORDER DMR-ES20D DVD RECORDING DVD-RAM / DVD-R / DVD-RW / +R OPEN/CLOSE REC /x1.3 This DVD Recorder is for viewing and recording free to view channels only, not pay TV or encrypted channels.
Table of Contents Page Page Important Safety Warnings / Caution Before You Start Included Accessories Product Introduction 3 4-5 4 5 Remote control Front Panel Rear Panel Display 21-pin Scart Socket Connecting with a 21-pin Scart cable Setup with Q Link Setup without Q Link Connecting with Audio/Video cable Connecting with S Video cable Connecting to Satellite Receiver Connecting with RF cable (Aerial cable) Auto-Setup with RF cable (Aerial cable) Removing Interference / Changing RF output channel Chec
Safety Precautions Important Safety Warnings ! The moulded three pin mains plug is supplied for your safety and convenience and must NOT be cut off. ! A 5 amp fuse is fitted in the mains plug. If the fuse has to be replaced, it must be of the same rating and approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. 1. Open the fuse cover with a screwdriver.
Before You Start Dear customer Thank you for your trust and your decision to purchase this top-quality device. Panasonic is one of the leading manufacturers of entertainment electronics devices. We are sure that you will be completely satisfied with this device. With the new Quick Start feature, the unit is ready for use within approx. 1 second. Thus, if a DVD-RAM was previously inserted, recording can begin immediately after the unit is switched on from Standby mode. Matsushita Electric Industrial Co.
Before You Start Inserting Batteries The batteries last for about a year, depending on how often you use the remote control unit. ! Do not mix old with new batteries, or batteries of different types. ! Only use batteries without any harmful substances (lead, cadmium, mercury). ! Do not use rechargeable type batteries. ! Remove the batteries if the remote control unit will remain unused for longer periods of time. ! Do not heat or short-circuit the batteries.
Remote control TV Standby/on switch Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power. Switching this unit into standby mode does not disconnect it from the mains. DIRECT TV REC Turn the television set on and off. CH 27 Direct TV record to DVD Select the AV input on the television set.
Remote control Point the remote control at the unit’s sensor. Avoid obstacles in the path of the transmission. The maximum range of the remote control is 7 m directly in front of the unit. Keep the transmission window and the unit sensor clean. The procedure can be impaired by direct sunlight or doors of glass cabinets. Child lock You can lock the buttons of the unit and the remote control. ! Press and hold RETURN and ENTER until X HOLD appears in the display. The unit is now locked.
Front Panel Panasonic Display Disc Tray DVD RECORDER DMR-ES20D DVD RECORDING DVD-RAM / DVD-R / DVD-RW / +R OPEN/CLOSE S VIDEO IN 1 EXT LINK CH 4 5 REC /x1.3 VIDEO IN L/MONO - AUDIO IN - R AV3 3 2 6 7 8 9 Standby/on switch Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power.
Display D ink D.MIX PLAY Information on the display TIMER-controlled recording. Blinking: There are less than 10 minutes until the start of a programmed TIMER recording. The device is not set to TIMER standby mode. ink External-Link display On: A TIMER-controlled recording is being performed by an external device. Current time, Disc recording and playback counter, various messages. Reading Disc. Recording PLAY Playback PL Number of Playlist T Track number G Group number PLAY D.
Connecting with a 21-pin Scart cable 1 Aerial RF cable / Aerial cable AV1 21-pin Scart socket RF IN Aerial input DVD Recorder S VIDEO OUT VIDEO RF OUT RF IN L L AV1 (TV) Y PB PR AUDIO AC IN OPTICAL R R AV2 (EXT) AV4 IN S VIDEO AV4 IN OUT COMPONENT VIDEO OUT (PROGRESSIVE/ DIGITAL AUDIO OUT INTERLACE) (PCM/BITSTREAM) AC IN~ RF OUT Aerial output 2 RF cable / 4 AC mains lead 3 21-pin Scart cable Necessary for TV with Q-Link Aerial cable TV Aerial input AV1 AC mains lead 4 Follow t
Setup with Q Link Download from TV using Auto-Setup Ch 35 4 Digital Suche Auto-Setup Sender, bitte in progress, warten. please wait. RETURN: RETURN: to abort abbrechen Download from TV RETURN Pos 4 Download in progress, please wait. RETURN: to abort Owner ID You can complete the Owner ID now or skip this step and do it later. To do it later, press the RETURN button. Your DVD Recorder is now ready to use. ! To set the Owner ID now, use and press the Numeric buttons or to enter a fourdigit PIN number.
Connecting with Audio/Video cable 1 Aerial Follow the steps below. RF cable / Aerial cable Disconnect the AC mains from all units. RF IN Aerial input DVD Recorder RF IN RF OUT L 1 Connect the aerial to the RF IN (Aerial input) of the DVD Recorder.
Connecting to a Satellite Receiver Parabolic antenna Aerial Sat cable 21-pin Scart socket Satellite receiv 2 er AC mains socket RF cable / Aerial cable 2 3 To AC mains socket TV RF IN Aerial input Aerial input 21-pin Scart cable (AV1) DVD Recorder AC mains socket RF cable / Aerial cable S VIDEO OUT VIDEO RF OUT RF IN L L AV1 (TV) Y PB PR AUDIO OPTICAL R R 2 AV2 (DECODER/EXT) AV4 IN OUT S VIDEO AV4 IN AC IN 1 COMPONENT VIDEO OUT (PROGRESSIVE/ DIGITAL AUDIO OUT INTERLACE) (P
Connecting with RF cable (Aerial cable) 1 Aerial Follow the steps below. RF cable / Aerial cable AC IN RF IN Aerial input Disconnect the power of all units. DVD Recorder S VIDEO OUT VIDEO RF IN RF OUT L 1 Connect aerial to the RF IN (Aerial input) connector of the DVD Recorder. 2 Connect the DVD Recorder´s RF OUT (Aerial output) to the TV set’s Aerial in connector. 3 Connect DVD Recorder and TV set to the AC mains socket.
Removing Interference / Changing RF output channel In some cases, interference (lines or patterning) or a very poor picture may appear on the TV when the DVD Recorder is connected. If this happens, follow the steps below to change the RF output channel to remove the interference. FUNCTIO NS TV screen The picture with interference RF OUTPUT CHANNEL ! Press the FUNCTIONS button for more than 5 seconds. The RF output channel number is displayed on the DVD display.
COMPONENT VIDEO OUT COMPONENT VIDEO OUT socket These sockets can be used for interlace or progressive output and deliver a clearer picture than the S VIDEO OUT socket. Connections via these sockets output colour difference signals (PB/PR) and brightness signal (Y) separately. The properties of the COMPONENT VIDEO input socket are dependent on the television set or screen. Always connect sockets of the same colour. Connect the Audio cable to the corresponding audio input sockets of the television.
External devices Connecting an analogue amplifier or an analogue system component In order to enjoy stereo or Dolby Pro Logic, connect the appropriate amplifier or an analogue audio component. ! ! Connect the analogue output (L/R) e.g. to a Dolby Pro Logic amplifier. As described, connect the Audio cable according to the colours and markings of the connection sockets (white/L, red/R).
TV Guide Tue 12/05/05 10:45 First use of the TV Guide: Programme information will be gradually stored on the TV Guide list after completion of Auto Setup or each time mains power to the unit is switched on. This process may take some time due to the nature of broadcast. Note: all programme information will be lost when mains power to the unit is switched off. FUNCTIO NS ENTER The electronic TV Guide provides a quick overview of the television and radio programmes of your digital stations.
TV Guide TV Guide: Landscape Category All Services Wed 13th BBC 1 2 BBC 2 3 ITV 1 4 Chan... 5 Five 6 ITV 2 7 S4C Prog.Type Movies All Types Movies 21:00 21:30 News Easten... D.I.Y. SOS Red Cap Entertainment Holiday Programme Hot Wars Sports Emmer... Coronation Street The Bill Children's Scrapheap Chall... Pepsi Chart Show Education Terminator 2 News Sex and the City Lifestyle News Pop Idol Me out of here ! Drama Scrapheap Chal...
Handling Discs Handling Discs If the surface of a disc that does not have or was removed from a cartridge is damaged, scratches, dirt, dust or fingerprints can compromise the recording, editing or playback. Such damage can also occur when the disc is inserted back into the cartridge. Only play round discs. Do not touch the recording surface of the disc. Cleaning the DVD-RAM Clean the disc with a special DVD-RAM cleaner (optional) and read the cleaner instructions throughly before use.
Disc formats RAM The disc can only be played back on DVD-RAM-compatible players. RAM You can use the playback and the DIRECT NAVIGATOR while the unit is in timerstandby mode. -R -RW(V) +R After the recording is complete, it takes approx. 30 seconds for the unit to finish the recording information. The first 30 seconds of a recording may be missing if you perform several TIMER-controlled recordings in a row.
Playback Switch the unit on. PLAY/x1.3 Playback Press OPEN/CLOSE to open the disc tray. Place the disc in the disc tray. Press PLAY . The disc tray is closed and playback begins. The reading of the disc may take some time! ! ! ! RAM -R -RW(V) +R -RW(VR) DVD-A DVD-V VCD CD PAUSE ! ! Playback begins with the last recorded title. Playback begins at the beginning of the disc. PAUSE during playback Press PAUSE Press PAUSE STOP during the playback. again to resume playback.
ECT DIR ATOR VIG NA Playback DIRECT NAVIGATOR TITLE VIEW Selecting programmes/titles for playback RAM -R -RW(V) +R -RW(VR) DVD RAM You can display the menu during playback, recording and in stop mode using the DIRECT NAVIGATOR button. 07 BBC1 12/ 9 THU ! ! Previous ENTER RETURN S SUB MENU Page 02/02 Select Next Previous Next ! Press DIRECT NAVIGATOR. Use to select the desired title and confirm with ENTER. Press RETURN to exit the menu. You can select other pages using SKIP Previous or Next.
Playback CREATE CHAPTER Splitting a recording into chapters ! RAM Press CREATE CHAPTER during playback. During playback press SKIP or SKIP to skip the chapter. MANUAL SKIP MANUAL SKIP ! Press MANUAL SKIP during playback. The playback jumps ahead approximately 30 seconds. TIME SLIP TIME SLIP ! ! ! ! RAM -R -RW(V) +R -RW(VR) Press TIME SLIP. Use to select the time that the playback should jump forward or back.
MP3 playback MENU G T TOTAL 1 1 1/ 12 No. 0 -- 9 Prev. Next SELECT ENTER RETURN No. 1 : Set Me Free Total 1 21 3 4 5 6 7 8 9 10 CD (MP3) Group Track 01- Father 01- Have your Way 01- Holy Spirit 01- Latter Rain 01- Love Of Heaven 01- Niemals 01- Only Truth 01- The Song Of The Lord 01- Never 01- We Seek His Face This unit can play MP3 files that were recorded with a computer on a CD-R/RW. Files are captured as tracks and folders as groups. “TOTAL” includes all tracks in all groups of the disc.
JPEG playback FUNCTIONS CD (MP3/JPEG) JPEG - MP3 Disc CD(MP3/JPEG) JPEG Playback mode Playback enu Recording EPG 23 The following information on the file type appears at the beginning: Playback mode is set to MP3. Select "JPEG" from MENU in FUNCTIONS if you play pictures ( JPEG ). MENU TV Guide TIMER RECORDING VIDEO Plus+ MENU ! Select file type.
Recording RAM -R -RW(V) +R You can record up to 99 titles on one disc (+R: 49 titles). If you use an unformatted DVD-RAM, you must format it before the first recording. The recording is saved in free areas on the disc. If there is no more space left on the target drive, you must delete recordings or use a new disc. When recording dual-channel or multi-audio TV programmes on DVD-R, DVD-RW or +R, only one audio channel can be recorded. Please select the desired audio channel in advance.
Recording Recording modes and approximate recording times in hours DVD+R DVD-RAM DVD-RW Single-sided Double-sided DVD-R (4.7GB) (9.4GB) (4.7GB) Picture quality XP SP XP (High quality) 1 2 1 LP SP (Normal) 2 4 2 EP (6 Hours)* LP (Long play) 4 8 4 EP (6 Hours) 6 12 6 EP (8 Hours) 8 16 8 EP (8 Hours) When recording on DVD-RAM in EP mode (8 Hours), playback may not be possible on DVD-RAM-compatible DVD players. In this case, select EP mode (6 Hours).
TIMER-controlled recordings Remain 1:58 SP 12:09:37 18/11 THU TIMER RECORDING STTL VPS Stop Stop Mode Mode PDC PDC NrNo.Name Name Datum Date Start Start 01 BBC1 18/11 THU 0:00 02 ITV 0:30 11:30 18/11 THU 10:00 New Timer Programme SP SP ON ON Disc space ! ! PROG/ CHECK ! ! ! ! Press ENTER to store new programme. ENTER RETURN Press PROG/CHECK. The TIMER RECORDING screen appears. Confirm the highlighted line with ENTER. Use to select the name of the TV station.
TIMER-controlled recordings TIMER RECORDING in the TV Guide TIMER RECORDING Remain 1:58 SP 12:09:37 12/ 5 THU Name Date Start You can select a programme that you want to record in the TV Guide list and transfer it directly to the TIMER RECORDING menu. Stop Mode STTL ! 23:00 SP OFF ! 5 Channel5 13/05 Wed 21:00 Channel5 Terminator 2 ! Programme Name Press ENTER to store the programme.
TIMER-controlled recordings RAM -R -RW(V) +R You can programme up to 16 programmes per month in advance. Insert a disc. VIDEO Plus+ is not supported for digital channels. Remain 1:58 SP 12:09:37 18/ 11 THU VIDEO Plus+ 8 5 3 4 2 VIDEO Plus+ Programming recordings with VIDEO Plus+ Enter PlusCode Number by using 0-9 keys. TIMER ENTER RECORDING RETURN Nr. Name Date 2 BBC2 18/11 THU 0 By entering a VIDEO Plus+ number, the TIMER-controlled recording is easy to set.
TIMER-controlled recordings SETUP Before TIMER recordings via external devices AV2 Settings AV2 Input Ext Link Tuning Disc Picture Sound Display Connection Others Video Ext Link 1 You control the recording function via an external device (e.g. receiver) using EXT LINK. Connect the external device with a 21-pin Scart cable to the AV2 socket. Adjust the Ext Link function for the connected device.
FUNCTIONS Selection Menu You can access the main functions via the FUNCTIONS selection menu. The illustrations show DVD-RAM menus. The menu entries can be different depending on the disc or medium. MP3&JPEG 25 - 26 ! FUNCTIO NS ! ! ! ! ! FUNCTIONS DVD-RAM Playback Press FUNCTIONS in stop mode. Use to select a menu and confirm with ENTER. Use to select an option and confirm with ENTER. To view the second screen page, use to select [To Others] and confirm with ENTER.
FUNCTIONS Selection Menu Symbols 35 DIRECT NAVIGATOR TIMER RECORDING Disc space STTL W W 01 BBC1 19/11 THU 8:00 02 ITV 19/11 THU 8:20 03 CH4 20/11 THU 10:30 8:30 9:00 11:30 ON ON ON SP SP SP New Timer Programme OK ! OK 29 PLAYLISTS 38 This title is currently being recorded. Remain 1:58 SP 12:09:37 18/11 THU VPS Nr No.Name Name Datum Date Start Start Stop Stop Mode Mode PDC PDC TIMER RECORDING W The title overlaps other programmes.
FUNCTIONS Selection Menu FUNCTIO NS DIRECT NAVIGATOR In DIRECT NAVIGATOR, you can archive, edit or start recordings after selecting a title. Direct access: ! Press DIRECT NAVIGATOR on the remote control. The DIRECT NAVIGATOR is displayed. DIRECT NAVIGATOR TITLE VIEW DVD RAM 07 BBC1 12/ 9 THU Previous ENTER RETURN S Page 02/02 SUB MENU Next Previous Select Next Access via the FUNCTIONS menu: ! Press FUNCTIONS in stop mode. ! Confirm DIRECT NAVIGATOR with ENTER.
FUNCTIONS Selection Menu FUNCTIO NS DIRECT NAVIGATOR ! Press FUNCTIONS. Confirm DIRECT NAVIGATOR with ENTER. In the TITLE VIEW menu, use to select the desired title. Press SUB MENU. ! In the sub menu, use ! Erase Properties Edit ! Enter Name Set up Protection Cancel Protection Partial Erase Change Thumbnail Divide Title Chapter View ! Enter Name to select [Edit] and confirm with ENTER. 34 RAM -R -RW(V) +R The complete name is displayed in the sub menu [Properties].
FUNCTIONS Selection Menu FUNCTIO NS DIRECT NAVIGATOR Chapter View In the sub menu, use to select [Chapter View] and confirm with ENTER. ! In the CHAPTER VIEW menu, use to select the desired title. ! Press SUB MENU, use to select the desired option in the sub menu and confirm with ENTER.
FUNCTIONS Selection Menu FUNCTIO NS PLAYLISTS To Others You can create and then edit a playlist from your favourite chapters of your recording. RAM Insert a recorded disc. If write protection is activated, deactivate it. Creating a Playlist ! PLAYLISTS DVD-RAM Create 03 ITV Source Title 02 01 ! 1/10 FRI CARS 03 04 Page 01/01 ! ! Source Chapter Page 001/001 Chapters in PLAYLIST Page 001/001 Create Chapter PLAYLISTS DVD-RAM Create Source Chap.
FUNCTIONS Selection Menu FUNCTIO NS PLAYLISTS To Others Edit Playlists Press FUNCTIONS. Use to select [To Others] and confirm with ENTER. ! Confirm PLAYLISTS with ENTER. ! Use to select a playlist. ! Press SUB MENU ! Use to select [Edit] and confirm with ENTER. ! In the sub menu, select the desired option. ! ! Erase Properties Edit Chapter View Create Copy Enter Name Change Thumbnail Copy Copy PLAYLIST Copy Cancel Create ! Confirm [Create] with ENTER. Please read Creating a Playlist.
FUNCTIONS Selection Menu FUNCTIO NS PLAYLISTS To Others Edit Chapter PLAYLISTS 01 23/ 9 THU 0:30 ! 02 03 1/10 FRI 0:10 1/10 FRI 0:20 ! ! ! Erase Properties Edit Chapter View PLAYLISTS Press FUNCTIONS. Use to select [To Others] and confirm with ENTER. Confirm PLAYLISTS with ENTER. In PLAYLIST VIEW, use to select a playlist. Press SUB MENU. Use to select [Chapter View] and confirm with ENTER.
FUNCTIONS Selection Menu FUNCTIO NS SETUP To Others ! ! ! ! ! ! Press FUNCTIONS in stop mode. Use to selec t [To Others] and confirm with ENTER. Use to select SETUP and confirm with ENTER. Use Use Use to select the desired sub menu and use to switch to setting. to select the desired setting and confirm with ENTER. to select the desired option and confirm with ENTER. Follow the menu navigation. The unit saves your settings. ! ! Use to return to the sub menu and use RETURN to exit the menu.
FUNCTIONS Selection Menu FUNCTIO NS SETUP To Others SETUP Tuning Edit Profiles Auto-Setup Restart Digital Add New DVB Service ! ! 45 BB Parlament 10 BBC FOUR 12 CBBC 13 CBEEBIES ! Profile Select ! Add Page + Page - v TO STORE, PRESS ENTER JUMP RETURN ENTER Creating profiles You can create four different profiles, in which you can sort and save your desired channels for the TV GUIDE.
FUNCTIONS Selection Menu FUNCTIO NS SETUP To Others Auto-Setup Restart Tuning Warning--all stored tuning data will be lost ! Do you want to proceed ? Yes SELECT ENTER Auto-Setup Restart ENTER Auto-Setup Restart Use to select [Yes] and confirm with ENTER. The station search begins. ! To cancel the process, use to select [No] and confirm with ENTER or press RETURN. ! To stop the station search early, press RETURN.
FUNCTIONS Selection Menu FUNCTIO NS SETUP To Others Manual Tuning SELECT ENTER RETURN Pos 901 902 903 904 905 906 907 908 909 910 Name BBC1 BBC2 ITV CH4 CH5 **** Delete Tuning Pos Name Ch Ch 22 911 23 912 24 913 25 914 26 915 8 Manual 16 Pos 95816 Pos Tuning 9517 Name 17 Name 18 Channel 19 NICAM 20 Title Page 901 BBC1 22 Off 301 CHANGE ENTER RETURN RETURN : leave ENTER : store Manual ENTER Changing the Name of the Television Station Use to select the name of the television station and confir
FUNCTIONS Selection Menu FUNCTIO NS SETUP Tuning Disc Picture Sound Display Connection Others SETUP To Others Comb Filter On Still Mode Automatic Seamless Play On Picture Settings ENTER Option ENTER [On] [Off] Comb Filter On: The picture becomes clear and contour-rich. This setting is always set to [On] if you have selected [TV System - NTSC]. Off: If the picture to be recorded is grainy. TAB SELECT [Automatic] [Field] [Frame] Still Mode RETURN Select the display of the still image.
FUNCTIONS Selection Menu FUNCTIO NS SETUP Tuning Disc Picture Sound Display Connection Others SETUP To Others DVB Preferred Subtitles On-Screen Messages Grey Background English Automatic On FL Display New Service Message Bright Automatic Display ENTER Select the language for DVB Subtitles. [Automatic] [Off] Automatic: The screen messages are displayed on the screen.
FUNCTIONS Selection Menu FUNCTIO NS SETUP To Others SETUP Remote Control Clock Owner ID Tuning Disc Picture Sound Display Connection Others Setting ENTER Option ENTER Remote Control Quick Start System Update Shipping Condition Default Settings TAB Others DVD 1 [DVD 1] [DVD 2] [DVD 3] Change the code of the remote control so that you can also use another Panasonic DVD unit at the same time. On 7 Clock Set the date and time.
FUNCTIONS Selection Menu FUNCTIO NS SETUP To Others Others EPG Download in Standby SETUP Tuning Disc Picture Sound Display Connection Others System Update EPG Download in Standby Software Update in Standby Software Update Search Now On On DVB Version: 0.31 ENTER Option ENTER [On] [Off] The unit is permanently looking for EPG data to fill up programme information in the TV Guide as long as it is tuned to a DVB channel, even in standby mode.
FUNCTIONS Selection Menu FUNCTIO NS DISC MANAGEMENT To Others ! DISC MANAGEMENT DVD-RAM Remain Title No. 1 Used 0:01 0:59(XP) Disc Name Off Disc Protection Erase all titles ! ! ! ! Press FUNCTIONS in stop mode. Use to select [To Others] and confirm with ENTER. Use to select DISC MANAGEMENT and confirm with ENTER. Use to select the desired menu and confirm with ENTER. Use FUNCTIONS to return to the FUNCTIONS menu. Format Disc SELECT ENTER RETURN Disc Name RAM -R -RW(V) +R ! Enter the name.
FUNCTIONS Selection Menu FUNCTIO NS DISC MANAGEMENT To Others DISC MANAGEMENT DVD-R ! Remain Title No. 1 Used 0:01 0:59(XP) ! Disc Name Top Menu Auto-Play Select Finalize ! ! Press FUNCTIONS. Use to select [To Others] and confirm with ENTER. Use to select DISC MANAGEMENT and confirm with ENTER. Use to select the desired menu and confirm with ENTER. Use FUNCTIONS to return to the FUNCTIONS menu.
DISPLAY menus DISPLAY menus contain information on the disc or the unit. With DVD-Video you can use the repeat function, change subtitles and perspectives, with DVD playback, you can change the picture and sound setting. Depending on the status of the unit (playback, stop), there are some entries that cannot be selected or changed. Subtitles, soundtrack and recording angle can only be selected if they were recorded on the disc. With some discs, these can only be changed via the disc menus.
STATUS displays (Banner) DVB only Banners contain compact programme information on the current and next programme. PAGE Displaying the Banner ! Change stations (CH ! Press ENTER or . CH or numeric buttons). Hiding the Banner ! Press RETURN or wait 5 seconds. 1 BBC ONE WALES Coronation Street 20:00 ~ 20:55 Bad Signal ! Press CH . The next or the previous channel are displayed. The banner information is updated and the tuner changes to the new channel.
STATUS displays STATUS Displaying the information ! ! ! Press STATUS. Press STATUS again. The display changes each time that the button is pressed. To exit the display, press STATUS. 1: Current medium 2: Current recording and playback state REC PAUSE Record Pause playback Pause recording Fast forward (5 speeds) Rewind (5 speeds) Slow motion Slow-motion rewind (5 speeds) Playback Quick View PLAYx1.3 (Playback x1.3) PLAY 4 DVD-RAM PLAY 1 2 10 DVB BBC1 3 5 6 Remain 10:07:21 1/12 T14 T14 0:05.
Before requesting service FUNCTION No function possible. The unit is switched on but cannot be used. The error code «H or «F » appears: », «U » The unit automatically switches to standby mode. PICTURE No picture. î There is a malfunction. The numbers following the letter «H» indicate the condition of the unit. ! Switch the unit to standby /I. If the unit does not switch to standby mode, press and hold /I for approx. 10 seconds or unplug it from the power supply for approx.
Before requesting service PLAYBACK Playback does not start. î The disc is dirty or badly scratched. î You inserted a disc that is not suitable for playback. î You inserted a blank disc. Black screen is played. î You may have recorded MHEG Data or encrypted programms. DVD-Video will not play. î Some DVD-Videos cannot be played if the security level has been changed. 44 No reaction when the button is pressed. î appears on the screen. The procedure is stopped by the unit or the disc.
Specifications Recording System DVD Video Recording format (DVD-RAM), DVD-Video format (DVD-R), DVD-Video format (DVD-RW) Recordable discs DVD-RAM : Ver. 2.0 Ver. 2.1/3×–SPEED DVD-RAM Revision 1.0 Ver. 2.2/5×–SPEED DVD-RAM Revision 2.0 DVD-R : for General Ver. 2.0 for General Ver. 2.0/4×–SPEED DVD-R Revision 1.0 for General Ver. 2.x/8×–SPEED DVD-R Revision 3.0 DVD-RW : Ver. 1.1 Ver. 1.1/2×–SPEED DVD-RW Revision 1.0 Ver. 1.2/4×–SPEED DVD-RW Revision 2.0 +R : Ver. 1.0 Ver. 1.1 Ver. 1.
