Operating Instructions - Language - English
Advanced operations
RQT5869
24
B
LS
RS
L
R
SW
i
h
g
C
SETUP
SELECT
ENTER RETURN
m s
m s
d B
0
d Bd B
L
Exit
Test
LS
R
SW
C
RS
d B
0
0
0
0
0
LS
LS
[B] [A] [C]
[A]
[A]
(L)[A] (L)[C] [B] (R)[C] (R)[A]
[C] [A]
A
STOP
PAUSE
PLAY
OPEN/CLOSE
SKIP
TOP MENU
MENU
DISPLAY
PLAY MODE SUBTITLE
AUDIO ANGLE
ENTER
RETURN
A-B REPEAT
CANCEL
6:9 5
∫; 1
SLOW / SEARCH
V.S.S.
<
REPEAT MODE
Í
SETUP
123
456
789
0
S
10
d
ef
3, 4, 2, 1
ENTER
C
FRONT (L) --)CENTER --)FRONT(R)
: ;
SURROUND (L)(------------ SURROUND(R)
Changing initial settings
[DVD]
Speaker setting
[DVD-RV41]
Select either “2-channel” or “Multi-channel” to suit the speakers you
have connected. You can change the following settings when you
select “Multi-channel”.
»
A
Speaker presence and size
1. Press [3,4,2, 1] to select the item and press [ENTER].
2. Press [3,4] to select the setting and press [ENTER].
Icon examples: Surround speaker (L)
Large: when the speaker supports low-frequency (under 100 Hz)
reproduction.
Small: Select when the speaker does not support low-frequency
reproduction.
The size setting for the front speakers is automatically determined by
the setting for the subwoofer.
»
B
Delay time
(Dolby Digital, center and surround speakers only)
For optimum listening with 5.1-channel sound, all the speakers, ex-
cept for the subwoofer, should be the same distance from the seating
position. If you have to place the center or surround speakers closer
to the seating position, adjust the delay time to make up for the differ-
ence.
If distance g (from the center speaker) and i (from the surround
speakers) are the same as or greater than h (from the front speak-
ers), leave the delay time as “0”, the factory preset.
If either distance g or i is less than h, find the difference in the
relevant table and change to the recommended setting.
³Center speaker
³Surround speakers
Changing the delay time
1. Press [3,4,2, 1] to select the delay time box and press
[ENTER].
2. Press [3,4] to adjust the delay time and press [ENTER].
»
C
Channel balance
1. Press [3, 4, 2, 1] to select “Test” and press [ENTER].
A test signal is output from one speaker at a time, starting with the
front left speaker and proceeding clockwise. (j)
2. While listening to the test signal, press [3, 4] to adjust the
volume of the center and surround speakers so they are the
same apparent volume as the front speakers.
(The front speakers cannot be adjusted here.)
3. Press [ENTER].
(The test signals are stopped.)
Note
No signal is output for the subwoofer. To adjust its volume, play
something, then return to this screen to adjust to suit your taste.
When you are finished
Press [3, 4, 2, 1] to select “Exit” and press [ENTER].
Surround
Center
b Exit
Front (L)
Subwoofer
Front (R)
Difference
Approx. 200 cm
Approx. 400 cm
Approx. 600 cm
Setting
5.3 ms
10.6 ms
15.9 ms
Difference
Approx. 50 cm
Approx. 100 cm
Approx. 150 cm
Approx. 200 cm
Setting
1.3 ms
2.6 ms
3.9 ms
5.3 ms
a Numbered
buttons
No Large Small
c Test
signal
j