Variable Speed Drill & Driver Model: EY6405/EY6409/EY6432 IMPORTANT This manual contains safety information. Read manual completely before first using this product, and save this manual for future use.
I. GENERAL SAFETY RULES FOR ALL BATTERY OPERATED TOOLS WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. • Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area 1) Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
A tool that cannot be controlled with the switch is dangerous and must be repaired. 15) Disconnect battery pack from tool or place the switch in the locked or off position before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. 16) Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.
III. FOR BATTERY CHARGER & BATTERY PACK 1) SAVE THESE INSTRUCTIONS -This manual contains important safety and operating instructions for battery charger EY0230. 2) Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery pack. 3) 4) 5) 6) 7) CAUTION -To reduce the risk of injury, charge only Battery Pack shown below.
19) The charger is designed to operate on standard household electrical power only. Do not attempt to use it on any other voltage! 20) Do not abuse cord. Never carry charger by cord or yank it to disconnect from outlet. Keep cord away from heat, oil and sharp edges. 21) Charge the battery pack in a well ventilated place, do not cover the charger and battery pack with a cloth, etc., while charging. 22) Use of an attachment not recommended may result in a risk of fire, electric shock, or injury to persons.
IV. FUNCTIONAL DESCRIPTION (B) (E) (I) (A) (C) (D) (F) (H) (G) * EY6405 is referred for illustration.
V. ASSEMBLY Attaching or removing bit Attaching or removing battery pack Note: When attaching or removing a bit, be sure to set the Forward/Reverse lever to its center position (switch lock). This tool is equipped with a keyless drill chuck. 1. Attachment Insert the bit and turn the lock collar clockwise (looking from the front) to tighten. 1. To connect the battery pack: Insert the battery pack. It snaps into place to indicate proper connection. 2.
Clutch Torque Setting Adjust the torque to one of the 18 possible settings or “ ” position to the job. CAUTION: Test the setting before actual operation. Set the scale at this mark ( ). Ni-Cd Battery pack (EY9106/EY9136) • Nickel cadmium battery pack requires a “BREAK-IN PERIOD” to reach maximum operating capacity. The “BREAK-IN PERIOD” is accomplished during normal usage during the first 6-8 charge and discharge cycles of the battery pack.
5. When in any of the conditions that battery pack is too cool, or the battery pack has not been used for a long time, the charging lamp starts flashing slowly to indicate protective charging. Protective charging takes longer to fully charge the battery pack, than the standard charging time. (Max. charging time is approx. 90 minutes). • If a fully charged battery pack is inserted into the charger again, the charging lamp may light up and then flash slowly.
IX. ACCESSORIES Use only bits suitable for size of drill’s chuck. MAXIMUM RECOMMENDED CAPACITIES Model EY6405 EY6409 M5 M5 M6 ø 6.8 mm (17/64") ø 6.8 mm (17/64") ø 8 mm (5/16") Machine screw Screw driving Wood screw Self-drilling screw Drilling EY6432 ø 6 mm (15/64") ø 6 mm (15/64") ø 6 mm (15/64") For Wood ø 27 mm (1-1/16") ø 27 mm (1-1/16") ø 36 mm (1-25/64") For Metal ø 10 mm (3/8") ø 13 mm (1/2") ø 13 mm (1/2") X.
ATTENTION For Ni-Cd Battery Packs, EY9106, EY9136 A nickel cadmium battery that is recyclable powers the product you have purchased. At the end of its useful life, under various state and local laws, it is illegal to dispose of this battery into your municipal waste stream. Please call 1-800-8-BATTERY for information on how to recycle this battery. FOR Ni-MH Battery Packs, EY9200, EY9201, EY9230, EY9231 A nickel metal hydride battery that is recyclable powers the product you have purchased.
30-DAY QUALITY SATISFACTION GUARANTEE: If you are dissatisfied with any Panasonic Cordless Power Tool for any reason, simply return it to the place of purchase with a dated proof of purchase, in the original packaging, with all accessories, parts and instructions, within 30 days of the date of purchase, for a full refund, or call Panasonic at 201-392-6655. Abuse or misapplication of any power tool voids the guarantee.