Cordless Drill & Driver Operating Instructions Model No: EY6450 IMPORTANT This manual contains safety information. Read manual completely before first using this product and save this manual for future use.
. GENERAL SAFETY RULES - FOR ALL BATTERY OPERATED TOOLS WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area 1) Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
14) Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with the switch is dangerous and must be repaired. 15) Disconnect battery pack from tool or place the switch in the locked or off position before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. 16) Store idle tools out of reach of children and other untrained persons.
8) During charging, the charger may become slightly warm. This is normal. Do not charge the battery for a long period. Symbol Meaning V Volts Direct Current n0 no load speed …/min revolutions or reciprocation per minutes safety and operating instructions for battery charger EY0110. 2) Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery pack. Forward Rotation Reverse Rotation 3) Rotation only WARNING: .
RECOMMENDED MINIMUM AWG SIZE OF EXTENSION CORDS FOR BATTERY CHARGERS AC Input Rating. Amperes AWG Size of Cord Equal to or But less Length of Cord, Feet greater than than 25 50 100 150 0 2 18 18 18 16 8) Do not operate charger with damaged cord or plug — replace them immediately. 9) Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman.
.FUNCTIONAL DESCRIPTION (A) (B) (E) (K) (I) (C) (J) (D) (F) (H) (G) (A) Keyless drill chuck (EY9799) (G) Battery pack(EY9251) (B) Clutch handle (H) Battery pack release button (C) Forward / Reverse lever (I) Battery charger (EY0110) (D) Variable speed control trigger (J) Support handle (E) Speed selector switch (K) Vent holes (F) Bit holder -6-
.ASSEMBLY Attaching or removing bit NOTE: When attaching or removing a bit, disconnect battery pack from tool or place the switch in the center position (switch lock). This tool is equipped with a keyless drill chuck. 1. Attachment Insert the bit and turn the lock collar clockwise (looking from the front) to tighten firmly until it stops clicking. Attaching or removing battery pack 1. To connect the battery pack: Insert the battery pack. It snaps into place to indicate proper connection. 2.
CAUTION: Do not operate Forward/Reverse lever until the chuck comes to a complete stop. Shifting during rotation of the chuck may damage the tool. tion. (Using at high speed while a strong force is applied may cause a motor breakdown.) Do not operate the speed selector switch (LOW-HIGH) while pulling on the speed control trigger. This can cause the rechargeable battery to wear quickly or damage the internal mechanism of the motor. *S e e a p p e n d i x f o r “ R E C O M MENDED SPEED SELECTION”.
For Appropriate use of Battery pack Battery charger (EY0110) 1. Plug the charger into the AC outlet. NOTE: Sparks may be produced when the plug is inserted into the AC power supply, but this is not a problem in terms of safety. 2. Insert the battery pack firmly into the charger. Battry pack Ni-MH Battery pack (EY9251) Charge the Ni-MH battery fully before storage in order to ensure a longer service life. The ambient temperature range is between 0°C (32°F) and 40°C (104°F).
NOTE: When charging a cool battery pack (below 5°C (41°F)) in a warm place, leave the battery pack at the place and wait for more than one hour to warm up the battery to the level of the ambient temperature. Otherwise battery pack may not be fully charged. Cool down the charger when charging more than two battery packs consecutively. Do not insert your fingers into contact hole, when holding charger or any other occasions. CAUTION: Do not use power source from an engine generator.
. SPECIFICATIONS MAIN UNIT Model Motor No load speed Chuck capacity Cluch stage LOW HIGH Stage1-15 Overall length Weight (with battery pack) EY6450 DC Motor 18 V 70 ~ 430 /min (rpm) 240 ~ 1500 /min (rpm) ø 0.5 ~ ø 13 mm (0 ~ 1/2") Approx. 2 Nm, (20 k f-cm, 18 in-lbs)~ 12 Nm, (122 k f-cm, 106 in-lbs) For powerful driving and drilling. 250 mm (9-13/16") 2.6 k , (5.7 lbs) BATTERY PACK Model Storage battery Battery voltage EY9251 Ni-MH Battery 18V DC (1.
30-DAY QUALITY SATISFACTION GUARANTEE: If you are dissatisfied with any Panasonic Cordless Power Tool for any reason, simply return it to the place of purchase with a dated proof of purchase, in the original packaging, with all accessories, parts and instructions, within 30 days of the date of purchase, for a full refund, or call Panasonic at 201-392-6655. Abuse or misapplication of any power tool voids the guarantee.