Model No. Número de modelo Scan, watch and discover how to get the most out of your TV TC-P42XT50 TC-P50XT50 Escanee, observe y descubra como obtener el máximo de su TV http://rd.pnaqr.com/TC-P00XT50/2/1/ Owner’s Manual 42”/50” Class 720p Plasma HDTV (41.9/49.9 inches measured diagonally) Manual de usuario Televisión de alta definición de 720p y clase 42”/50” de Plasma (41,9/49,9 pulgadas medidas diagonalmente) For assistance (U.S.A./Puerto Rico), please call: 1-877-95-VIERA (958-4372) www.panasonic.
This product incorporates the following software or technology: (1) the software developed independently by or for Panasonic Corporation, (2) the software owned by third party and licensed to Panasonic Corporation, (3) the software based in part on the work of the Independent JPEG Group, (4) the software developed by the FreeType Project, (5) the software licensed under the GNU LESSER GENERAL PUBLIC LICENSE (LGPL) and/or, (6) open sourced software other than the software licensed under the LGPL.
VIERA Link™ is a trademark of Panasonic Corporation. HDMI, the HDMI logo and HighDefinition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. Contents Please read before using the unit SDXC Logo is a trademark of SD3C, LLC. “RealD 3D” is a trademark of RealD. DLNA®, the DLNA Logo and DLNA CERTIFIED™ are trademarks, service marks, or certification marks of the Digital Living Network Alliance.
Safety Precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. No user-serviceable parts inside. Refer servicing to qualified service personnel. WARNING: The lightning flash with arrowhead within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons.
● In the unlikely event that you receive a shock from this product, it is possible that your household outlet may be wired improperly. Have an electrician verify that the TV’s outlet is properly wired. If the symptom persists, have the TV serviced by a qualified authorized technician.
WARNING/CAUTION (3D Eyewear) ● Be careful not to close the hinge section of the 3D WARNING ■ Accidental Ingestion ● Keep 3D Eyewear parts in places out of the reach of children. There is a danger small children could swallow such parts by mistake. • If a child accidentally swallows such parts, seek immediate medical attention. ■ Place ● Do not use 3D Eyewear in hospital or other medical facilities. Radio waves from 3D Eyewear may cause interference of medical equipments.
FCC and IC STATEMENT This equipment has been tested and found to comply with the limits for an Other Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Accessories/Optional Accessories Accessories Check you have all the items shown. Accessories Remote Control Transmitter N2QAYB000704 Batteries for the Remote Control Transmitter (2) Power cord AA Battery Ferrite core for HDMI cable (2) Owner’s Manual Quick start guide Child safety Product Registration Card (U.S.A.) Optional Accessories 3D Eyewear (Rechargeable type) ● TY-ER3D4S ● TY-ER3D4M for USB cable (2) Pedestal How to assemble (p.
■Assembling the pedestal Insert the protrusion of the Neck into the Base firmly. Neck Attaching the pedestal to TV Turn the stand over and fix stand neck securely with assembly screws. (3 screws) • Do not hold the neck when turning over the stand. XYN4+F10FNK (Black) size (M4 x 10) (5) B x 3 pcs. Protrusion of the Neck (bottom) Hole for screw Front Back of Stand Attach the Bracket to the protrusion of Neck. Make sure that the bracket is anchored before fixing the screws.
Power cord connection To attach To remove Keep pushing both sides until they snap and pull. Insert it firmly until the tabs on both sides click into place. Attaching Ferrite Core Be sure to attach the provided ferrite core to the HDMI cable/USB cable (not supplied) to reduce interference or electrical noise. Attach the ferrite core as close as possible to connector on the TV side as shown. Close the ferrite core until it clicks.
Connections Connection Panels DIGITAL AUDIO OUT Back of the TV ETHERNET connector Getting started SD card slot B C A USB connector * See page 10 (Power cord connection) Back of the TV VHF/UHF Antenna Cable TV Power Cord (Connect after all the other connections have been made.
AV cable connection Best To use HDMI terminals AV Equipment HDMI AV OUT e.g. Blu-ray Disc player DVI OUT HDMI-DVI Conversion cable AV Equipment L Connect to Audio input terminal HDMI connection (p. 41) R AUDIO OUT ● VIERA Link connection, please refer to p. 26 e.g. Blu-ray Disc player To use COMPONENT terminals Y red green green PB COMPONENT Good blue green blue blue VIDEO OUT red red L white red AV Equipment PR white white AUDIO R OUT red e.g.
Identifying Controls TV controls/indicators Front of the TV Back of the TV Changes the input mode Chooses Menu and Submenu entries (Press and hold down for MENU function) Selects channels in sequence POWER button Power indicator (on: red, off: no light) Remote control sensor Within about 23 feet (7 meters) in front of the TV set • An image of the control panel is displayed on the screen while using it. Remote control Closed Caption On/Off (p.
First Time Setup The first time setup screen is displayed only when the TV is turned on for the first time, after the power cord is inserted into a wall outlet and the “Auto power on” is set to “No”.
Watching TV Turn power on (Remote) (TV) Note Please select correct input --> (p. 17) or Select a channel number When tuning to a digital channel, press the button to enter the minor number in a compound channel number. or down • CH buttons are also available on the side of the TV. [For Cable/Satellite box connection] - Use your connected box’s remote control.
Change aspect ratio and Zoom the picture ■ Press FORMAT to cycle through the aspect modes (p. 39) • 480i, 480p: FULL/JUST/4:3/ZOOM • 1080p, 1080i, 720p: FULL/H-FILL/JUST/4:3/ZOOM Use when the picture does not fill the whole screen (bars appears on either side of the image) or portions of the picture is trimmed. Note 1. Some content, such as film-based movies, are available in extra-wide format. Top and bottom bars are unavailable. 2.
Using VIERA TOOLS VIERA TOOLS is the easy way to access the TV’s special features. They are displayed as shortcut icons on the TV screen. Display VIERA TOOLS and select the item select next Set each item 3D VIERA Link Change the view 3D⇔2D (p. 19) VIERA Link menu (p. 29) Game mode Media player Media player (p. 20-24) Change to “Game” mode. Eco mode Using DLNA feature (p.
Viewing 3D images on TV Precautions for Viewing 3D Images Cautions During Viewing Do not use devices that emit strong electromagnetic waves (such as cellular phones or personal transceivers) near the 3D Eyewear. Doing so may cause the 3D Eyewear to malfunction. If the 3D Eyewear is used in a room in which fluorescent lights (50 Hz) are used, the light within the room may appear to flicker. In this case, either darken or switch off the fluorescent lights when using the 3D Eyewear.
Change the view 3D⇔2D ■ Simply switches 3D ⇔ 2D images (Auto mode) select 3D format select ● VIERA TOOLS -->p. 17 ”3D” icon also available. 3D 2D OK (example) ● Switches to Manual mode (see below) ■ Change 3D format (Manual mode) During above operation press red button and switch to Manual mode.
Using Media player You can view still and motion images and play music saved on a USB flash memory and an SD card.
Viewing Contents Insert Media (SD card or USB flash memory) • Auto play setting Setup > Advanced setup > Image viewer auto play Display Media player Select Drive and Media (Display connected drive) Media player Media player select Drive select select Media select OK OK OK OK Select Select RETURN RETURN Photos Videos Music SD memory card SD memory card Select the data (Photos/Videos/Music) How to view the data differs depending on data storage conditions.
Photos view [Photos thumbnail] Media p layer [Features] Photos Select OPTION Slideshow ● Slideshow setting ● Sort ● Drive select ● Media select All photos * In DMR mode, Slideshow is not available DMR: Digital Media Renderer ● Colored button operation (except red button ) is not available in DLNA mode.
Sort Display “Sort select” menu and select item Displayed each view select Media player Photos • Folders (ascending order of numeric/alphabetical) • Sort by month (ascending order of the month) • Sort by date Sort by Date Folders Sort by date 23/10/2009 25/10/2009 01/11/2009 05/11/2009 10/11/2009 24/11/2009 01/12/2009 03/12/2009 20/12/2009 22/12/2009 22/11/2009 23/11/2009 Sort by month OK Select SD memory card OK OPTION Slideshow RETURN Sort Info Drive select Media select (e.g.
Videos view [Videos thumbnail] Media p layer [Features] Videos Trip1 Trip2 Trip3 Trip4 Trip5 Room Nature1 Nature2 Nature3 Nature4 Nature5 Nature6 2009_4 2009_7 * In DMR mode, Resume playback is not available ● Play ● Drive select ● Media select Titles/Folders view ● Colored button operation is not available in DLNA mode. 2009_9 Select SD memory card OK OPTION Info RETURN Play Drive select Media select [Videos playback screen] SD 01/04/2010 15:34 00:00.10 00:00.
VIERA LinkTM “HDAVI ControlTM” Simultaneously control all Panasonic “HDAVI Control” equipped components using one button on the TV remote. Enjoy additional HDMI Inter-Operability with compatible Panasonic products. This TV supports “HDAVI Control 5” function. Connections to equipment (Blu-ray Disc player, DVD recorder DIGA, HD Camcorder, Home theater system, Amplifier, etc.) with HDMI cables enables VIERA Link controls.
VIERA Link™ Connections (with VIERA Link function) ■ Terminal overview Back of the TV ■ Connecting Blu-ray Disc player/DVD Recorder (DIGA) HDMI cable Blu-ray Disc player/DVD recorder (DIGA) with VIERA Link function ■ Connecting Home theater system/AV amp HDMI 2 is recommended.
VIERA Link settings and Available features To use all VIERA Link functions: After everything is connected, in VIERA Link settings menu, set “VIERA Link” to “On”. Some features are disabled depending on the “HDAVI Control” version of the equipment. Please check the list (p. 25) Select “VIERA Link settings” Menu Picture Audio Setup 2/2 VIERA Link settings Keyboard type U.S.
Automatic Input Switching When using a Blu-ray Disc player, DVD player/recorder or Home theater system, the TV will automatically change to the appropriate input, when playback begins on one of those devices. • For a Home theater system the speakers automatically switch to the theater system. Power on link Yes: The TV is turned on automatically and switches to the appropriate HDMI input whenever VIERA Link compatible equipment is initially turned on and the Play mode is selected.
VIERA Link menu and Available features Some features are disabled depending on the “HDAVI Control” version of the equipment. Please check the list (p. 25) Display the VIERA Link menu select next select VIERA Link control in the VIERA Link menu may be grayed out if no • Items compatible equipment is connected (must be HDAVI Control 2 or later) or if the equipment has not initiated a connection with the TV. In that case, switch the equipment’s power Off and On while the TV is On.
Using Network services Network Connections Contact your Broadband service provider NOTICE: If you don’t have Internet service by your local provider, please order a high-speed Internet service at no less than the following connection speed. If you already have such service, make sure that the connection speed exceeds the following. ● Required speed (effective): at least 1.5 Mbps for SD and 6 Mbps for HD picture quality, respectively. ● Dial-up Internet service cannot be used for Online Movies.
Network settings This is a setting for connecting to a broadband environment. Select “Network” Select the settings and set Menu select Network Connection test Picture adjust Network connection Wireless (WiFi) Wireless network settings Audio IP address/DNS settings Network Network link Online Movies settings Timer New software notice On Network status Setup Connection test Check that the Network settings are as shown below, and then start “Connection test”.
IP address/DNS settings ■ Manual setting Select “IP/DNS setting mode” and set to “Automatic” Select “IP/DNS setting mode” and set to “Manual” Select the item and press OK Check the specifications of the broadband router and enter each IP address. Or Enter each IP address as was specified by the provider (When IP/DNS automatic acquisition in DHCP can be used) Menu IP address/DNS settings Picture Audio Network IP setting mode Automatic IP address 192.168.0.5 Subnet mask 255.255.255.
Online Movies settings Select “Online Movies settings” Menu Picture Audio Network Connection test Network connection Wireless (WiFi) Wireless network settings IP address/DNS settings Network Timer Lock select Network link Select item and set to “Off” (Available services are displayed.) The items are not displayed on Online Movies screen.
Enjoy Online movies This function allows you to access VOD (Video-on-demand) services, easily with selecting the icon. ● You need broadband environment to use this service. Preparations ● Network connections (p. 30) ● Network settings (p. 31-33) Display the Online Movies screen Select the item and press OK select view (example) * Depending on the usage conditions, it may take a while to read all the data. • The services are subject to change without notice.
Using DLNA feature You can share the contents (Photo, Video, Music etc.) stored in DLNA Certified media server with your home network system. Preparations ● Network connections (p. 30) ● Network settings (p. 31-33) Display VIERA TOOLS and select the “DLNA” select next Select server select DLNA server A 5 g Using Network services Display available server.
Editing and Setting Channels The current channel settings can be changed according to your needs and reception conditions.
Manual program (Set manually) Use this procedure when changing the channel setup or changing the channel display. Also, use this to add or skip channels from the channel list manually. You can select a channel tuning mode (Digital only/Analog only) in “Channel surf mode” Edit ● Caption Edit CH caption Channel Select Apply Favorite Add ... Yes 3 ... ... Yes 4 ... ... Yes 5 ... ... select next Caption Select or edit the station identifier.
How to Use Menu Functions Various menus allow you to set the picture, sound, and other functions so that you can enjoy watching TV best suited for you. Display the menu Menu structure Menu Picture Audio Input labels HDMI 1 HDMI 2 Component/Video Network ● Shows the functions that can be adjusted. ● Some functions will be disabled depending on the type of input signal. Menu bar Press OK to move to the Menu items. Menu items Press OK to proceed to the next screen if available.
Technical Information Ratings List for parental control “V-chip” technology enables you to lock channels or shows according to standard ratings set by the entertainment industry. ■ U.S. MOVIE RATINGS (MPAA) NR G PG PG-13 R NC-17/X ■ CANADIAN ENGLISH RATINGS (C. E. L. R.) Not Rated. All children and General Audience. Parental Guidance suggested. Parental Guidance for children under 13. Restricted Viewing, parental guidance is suggested for children under 17. No one 17 or under allowed.
H size ● Aspect Ratio: 4:3 Size 1 Size 2 ● The width will be decreased on both sides to reduce noise. ● Aspect Ratio: FULL/JUST(H-FILL/ZOOM) Size 1 Size 2 ● The width will be increased on both sides to reduce noise.
Cautions when handling SD Cards operation of the unit. (Panasonic is not liable for any deterioration or damage of recorded data.) mm 2.1 32 mm ● Use an SD Card which meets SD standards. If not, it may cause the TV to malfunction. ● Do not remove the card while the unit is accessing data (this can damage card or unit). ● Do not touch the terminals on the back of the card. ● Do not subject the card to high pressure or impact.
DIGITAL AUDIO OUT terminal You can enjoy your Home theater by connecting a Dolby Digital (5.1 channel) decoder and “Multi Channel” amplifier to the DIGITAL AUDIO OUT terminals. Caution ● Depending on your DVD player and DVD-Audio software the copyright protection function may operate and disable optical output. ● When an ATSC channel is selected, the output from the DIGITAL AUDIO OUT jack will be Dolby Digital. When an NTSC channel is selected, the output will be PCM.
Care and Cleaning First, unplug the Power cord plug from the wall outlet. Display panel The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft, lintfree cloth. ● If the surface is particularly dirty, after cleaning up the dust, soak a soft, lint-free cloth in diluted mild liquid dish soap (1 part mild liquid dish soap diluted by 100 times the amount of water), and then wring the cloth to remove excess liquid.
Frequently Asked Questions (FAQ) If there is a problem with your TV, please refer to the table below to determine the symptoms, then carry out the suggested check. If this does not solve the problem, visit the Panasonic website for further assistance. (see cover) Questions Answers Picture How do I view the picture from devices such as a: Cable/Satellite box, game console, Blu-ray or DVD player? Press the INPUT button on the remote to select the correct input source.
Questions Answers Sound Why is there no sound coming from the TV? Make sure the volume is up and MUTE is off. Confirm the TV speakers are set to ON by pressing MENU and selecting “Audio” --> “Advanced audio”. Check that the correct SAP (Secondary Audio Program) is selected by pressing the SAP button on the remote control. (p. 15) If the TV is connected to a Panasonic Home Theater via HDMI cable, then check VIERA Link controls. (p.
Questions 3D Other 46 Answers Why doesn’t my 3D video source looks 3D? 1. Begin playing the 3D video source. 2. Ensure that the Panasonic 3D Eyewear (glasses) are on (check the glasses battery) 3. Press “3D” button directly or press the VIERA TOOLS button on the TV’s remote control and select “3D” 4. In the “3D format select” menu, select “3D”. Notes: 1. 3D Blu-ray discs must be played with a 3D capable Blu-ray player. 2. Check with your Cable or Satellite provider if their supplied box is 3D capable.
Specifications TC-P42XT50 Display Panel Power Source Power Consumption (Rated power / Standby power) Panel System TC-P50XT50 AC 120 V, 60 Hz 219 W / 0.3 W 272 W / 0.3 W Plasma Display panel Screen size 42 ” class (41.9 inches measured diagonally) 50 ” class (49.9 inches measured diagonally) W × H × Diagonal 36.5 ” × 20.5 ” × 41.9 ” (928 mm × 522 mm × 1,065 mm) 43.5 ” × 24.4 ” × 49.
Index A B C D E F H I L M N O P R S T U Accessories ............................................................. 8 Ant/Cable ............................................................... 36 Antenna ..................................................................11 Auto Program ......................................................... 36 Battery ................................................................... 10 Cable .................................................................
Limited Warranty (for U.S.A.
Customer Services Directory (for U.S.A. and Puerto Rico) Customer Services Directory (United States and Puerto Rico) Obtain Product Information and Operating Assistance; locate your nearest Dealer or Service Center; purchase Parts and Accessories; or make Customer Service and Literature requests by visiting our Web Site at: http://www.panasonic.com/help or, contact us via the web at: http://www.panasonic.
Limited Warranty (for Canada) Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 PANASONIC PRODUCT – LIMITED WARRANTY Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship under normal use and for a period as stated below from the date of original purchase agrees to, at its option either (a) repair your product with new or refurbished parts, (b) replace it with a new or a refurbished equivalent value product, or (c) refund your purchase price.
TC-P42XT50 42" Plasma HDTV SPECIFICATIONS Dimensions (W x H x D) Mass Power Source Power Consumption 39.8" (1,009 mm) x 26.1" (663 mm) x 12.6" (320 mm) (Including pedestal) 39.8" (1,009 mm) x 24.3" (616 mm) x 3.3" (84 mm) (TV Set only) 44.1 lb. (20.0 kg) (Including pedestal) 37.5 lb. (17.0 kg) (TV Set only) AC 120 V, 60 Hz 219 W (Rated power) 0.3 W (Standby power) DIMENSIONS JACKS Top View Side Panel Front View Side ViewBack 3.3 (84) 24.3 (616) 39.
TC-P50XT50 50" Plasma HDTV SPECIFICATIONS Dimensions (W x H x D) Mass Power Source Power Consumption 46.7" (1,186 mm) x 30.1" (764 mm) x 13.2" (335 mm) (Including pedestal) 46.7" (1,186 mm) x 28.2" (717 mm) x 3.3" (84 mm) (TV Set only) 56.2 lb. (25.5 kg) (Including pedestal) 48.5 lb. (22.0 kg) (TV Set only) AC 120 V, 60 Hz 272 W (Rated power) 0.3 W (Standby power) DIMENSIONS JACKS Top View Side Panel Front View Side ViewBack 3.3 (84) 28.2 (717) 46.
USA Only: Disposal may be regulated in your community due to environmental considerations. For disposal or recycling information, please visit Panasonic website: http://www.panasonic.com/environmental or call 1-888-769-0149. Sólo Estados Unidos: La disposición puede estar regulada en su comunidad debido a consideraciones ambientales. Para información sobre la disposición o reciclaje, por favor visite la página web de Panasonic: http://www.panasonic.com/environmental o llame al 1-888-769-0149.